A modular cable management device. Modular design allows volume expansion by stacking “cable-roll-ext-thewhatbrandsg.stl”.

Dimensions:
- Cable Roll Diameter - 56.4mm.
- Centre Hole Diameter - 44mm.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5 (for strength).
- No supports are needed but follow the suggested print orientation for ideal results.

Assembly
The snap-on "Cap (cable-roll-cap-thewhatbrandsg.stl)" piece may be snug initially but should loosen up after a few rotations around the roll.

Changelog:
- 1 Jul 2024: Added a “Cap Ext” for use with one "cable-roll-ext-thewhatbrandsg.stl".


_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Cable Organiser - Cable Roll

cable-roll-a-thewhatbrandsg.stl

cable-roll-ext-thewhatbrandsg.stl

cable-roll-cap-ext-thewhatbrandsg.stl

Extension for the popular **Flexi-Rex** by [@DrLex](https://www.printables.com/@DrLex). You can access the original Flexi-Rex for download [HERE](https://www.printables.com/model/46241-flexi-rex-with-stronger-links). I am using "Flexi-Rex-improved.stl" version in my make. There have been no alterations made to the Rex itself.


Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- No supports are needed.


Assembly
No adhesive is required. Friction fit. Print the Flexi-Rex separately using the link above.


_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

[REMIX] Flexi-Rex or Flexi-Dragon?

remix-flexidragon-flame-outer-thewhatbrandsg.stl

Over-engineered book/page holder for one-handed reading - comes in two versions: Bookmark and Portable.

Suggested print settings for the Bookmark version:
- Layer height 0.2mm.
- Infill 80%.
- Perimeters: 5.
- No supports are needed.
 

Suggested print settings for the Portable version:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5.
- No supports are needed.
 

Assembly
Gently flex the "Cap" at the gap before slotting it through the eye.


_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Page Holder - 2 Versions

bookmark-holder-cap-v2-thewhatbrandsg.stl

Modular cone design, you can achieve various sizes and functions by swapping different components - with more additional parts to be introduced later.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5 (for strength).
- No supports are needed but follow the suggested print orientation for ideal results.

Slight effort may be required when initially screwing the parts together. If you encounter tight threading, try threading the parts back and forth a couple of times before fully threading them in.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Modular Traffic / Construction Cone (Tabletop Miniatures)

base-1-v3-thewhatbrandsg.stl

orange-3-v3-thewhatbrandsg.stl

A slim, portable design that easily fits in any pocket, holding 3 SD cards plus an attachment for Micro SD cards.

Suggested print settings for the **Main Body**:
- Layer height 0.2mm.
- Infill 20%.
- Perimeters: 5 (for strength and aesthetic).
- No supports are needed.

Suggested print settings for **Micro SD attachment**:
- Layer height 0.2mm.
- Infill 15%.
- Brim Width: 2mm.
- Brim Separation Gap: 0.2mm.
- No supports are needed but follow the suggested print orientation for ideal results.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Minimalistic Card-sized SD Card Holder

sd-inner-thewhatbrandsg.stl

sd-microholder-bottom-thewhatbrandsg.stl

sd-microholder-top-thewhatbrandsg.stl

A Voronoi model remix of LXO's "[Lowest poly The Thinker](https://www.printables.com/model/1165-lowest-poly-the-thinker)".

Suggested print settings:
- Layer height 0.2mm.
- Infill 20%.
- Perimeters: 3.
- No supports are needed.
- Models in pictures are printed at 50% scale.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

[REMIX] The Thinker - Voronoi Edition

remix-thinker-v2-voronoi-thewhatbrandsg.stl

An "inviting" name/business card holder.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Supports are needed.
- Some post-support cleaning is required.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Name Card Holder - Take One

namecard-holder-thewhatbrandsg.stl

Our take on the classic ACME-branded anvil. Any Road Runner fans in the house? Beep Beep.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- No supports are needed but follow the suggested print orientation for ideal results.
 
Assembly
The components fit together using a friction-fit mechanism. Push the base in until you feel a "click". Slight effort is needed to secure the components; use adhesive if necessary.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

ACME Anvil (Tabletop Miniatures)

anvil-top-v2-thewhatbrandsg.stl

The Anywhere Door (Dokodemo Door in Japanese) is an iconic "gadget" from the Doraemon comic.

Dimensions:
- Height: 16.4cm
- Width: 8.73cm
- Depth: 1.465cm
 
Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5 (for strength).
- Print-in-Place.
- No supports are required.
 
Assembly
Slight effort is required when first loosening the hinge. The base isn't necessary when the door is kept in a closed position.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Doraemon Anywhere Door 任意门 (Tabletop Miniatures)

doraemon-anywheredoor-pip-thewhatbrandsg.stl

A slim and portable design that fits easily in any pocket, capable of holding 4 x Nintendo game cards.


Suggested print settings for the Main Body (inner):
- Layer height 0.2mm.
- Infill 20%.
- Perimeters: 5 (for strength and aesthetic).
- No supports are needed.
 

Suggested print settings for Cover (outer):
- Layer height 0.2mm.
- Infill 20%.
- Perimeters: 5 (for strength and aesthetic).
- No supports are needed.


_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._


This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Minimalistic Card-sized Nintendo Game Card Holder

switch-outer-thewhatbrandsg.stl

A sleek, compact and modular tray for small items designed for 2020 profiles. Modular design, utilise "2020-tray-centre-thewhatbrandsg" to extend the length of the tray.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5.
- No supports are needed.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

2020 Profile Slim Tray

2020-tray-centre-thewhatbrandsg.stl

Tin can container with the divider inserts. 🥫

Suggested print settings for Can:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 3.
- No supports are needed but follow the suggested print orientation for ideal results.
 
Suggested print settings for Divider Inserts:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5 (for strength and aesthetic).
- No supports are needed but follow the suggested print orientation for ideal results.
 
_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Tin Can

can-thewhatbrandsg.stl

Dimensions: 1.5 x 1.5 x 1.5cm.

**Suggested print settings:**
- Layer height 0.2mm.
- Infill 15%.
- No supports are needed.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Dice - Lines

dice-lines-2-etc.stl

base-1-extension-v3-thewhatbrandsg.stl

base-1-mini-v3-thewhatbrandsg.stl

base-1-small-v3-thewhatbrandsg.stl

orange-5-v3-thewhatbrandsg.stl

white-2-v3-thewhatbrandsg.stl

white-4-v3-thewhatbrandsg.stl

cone-connector-thewhatbrandsg.stl

cable-roll-b-thewhatbrandsg.stl

cable-roll-cap-thewhatbrandsg.stl

bookmark-holder-bot-v2-thewhatbrandsg.stl

bookmark-holder-top-v2-thewhatbrandsg.stl

bookmark-holder-top2-v2-thewhatbrandsg.stl

portable-holder-bot-v2-thewhatbrandsg.stl

portable-holder-cap-v2-thewhatbrandsg.stl

portable-holder-top-v2-thewhatbrandsg.stl

remix-flexidragon-eye-thewhatbrandsg.stl

remix-flexidragon-flame-inner-thewhatbrandsg.stl

I'm Ed, a maker and 3D printing enthusiast from Singapore. I enjoy creating gadgets, functional designs, and backpack hardware. Here to learn, seek inspiration, share and have an incredible time. =D

@TheWhatBrandSG

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

wined11

Achievements

Seedling

Fan Favorite

Explorer

Pinned models

Modular Traffic / Construction Cone (Tabletop Miniatures)

Cable Organiser - Cable Roll

Page Holder - 2 Versions

[REMIX] Flexi-Rex or Flexi-Dragon?

Cable Organiser - Cable Roll

[REMIX] Flexi-Rex or Flexi-Dragon?

Page Holder - 2 Versions

Modular Traffic / Construction Cone (Tabletop Miniatures)

Minimalistic Card-sized SD Card Holder

[REMIX] The Thinker - Voronoi Edition

Name Card Holder - Take One

ACME Anvil (Tabletop Miniatures)

Doraemon Anywhere Door 任意门 (Tabletop Miniatures)

Minimalistic Card-sized Nintendo Game Card Holder

2020 Profile Slim Tray

Tin Can

Dice - Lines