Modular cone design, you can achieve various sizes and functions by swapping different components - with more additional parts to be introduced later.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5 (for strength).
- No supports are needed but follow the suggested print orientation for ideal results.

Slight effort may be required when initially screwing the parts together. If you encounter tight threading, try threading the parts back and forth a couple of times before fully threading them in.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Modular Traffic / Construction Cone (Tabletop Miniatures)

base-1-extension-v3-thewhatbrandsg.stl

base-1-mini-v3-thewhatbrandsg.stl

base-1-small-v3-thewhatbrandsg.stl

base-1-v3-thewhatbrandsg.stl

orange-3-v3-thewhatbrandsg.stl

orange-5-v3-thewhatbrandsg.stl

white-2-v3-thewhatbrandsg.stl

white-4-v3-thewhatbrandsg.stl

cone-connector-thewhatbrandsg.stl

A modular cable management device. Modular design allows volume expansion by stacking “cable-roll-ext-thewhatbrandsg.stl”.

Dimensions:
- Cable Roll Diameter - 56.4mm.
- Centre Hole Diameter - 44mm.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5 (for strength).
- No supports are needed but follow the suggested print orientation for ideal results.

Assembly
The snap-on "Cap (cable-roll-cap-thewhatbrandsg.stl)" piece may be snug initially but should loosen up after a few rotations around the roll.

Changelog:
- 1 Jul 2024: Added a “Cap Ext” for use with one "cable-roll-ext-thewhatbrandsg.stl".


_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Cable Organiser - Cable Roll

cable-roll-a-thewhatbrandsg.stl

cable-roll-b-thewhatbrandsg.stl

cable-roll-cap-thewhatbrandsg.stl

cable-roll-ext-thewhatbrandsg.stl

cable-roll-cap-ext-thewhatbrandsg.stl

Over-engineered book/page holder for one-handed reading - comes in two versions: Bookmark and Portable.

Suggested print settings for the Bookmark version:
- Layer height 0.2mm.
- Infill 80%.
- Perimeters: 5.
- No supports are needed.
 

Suggested print settings for the Portable version:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5.
- No supports are needed.
 

Assembly
Gently flex the "Cap" at the gap before slotting it through the eye.


_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Page Holder - 2 Versions

bookmark-holder-bot-v2-thewhatbrandsg.stl

bookmark-holder-cap-v2-thewhatbrandsg.stl

bookmark-holder-top-v2-thewhatbrandsg.stl

bookmark-holder-top2-v2-thewhatbrandsg.stl

portable-holder-bot-v2-thewhatbrandsg.stl

portable-holder-cap-v2-thewhatbrandsg.stl

portable-holder-top-v2-thewhatbrandsg.stl

Extension for the popular **Flexi-Rex** by [@DrLex](https://www.printables.com/@DrLex). You can access the original Flexi-Rex for download [HERE](https://www.printables.com/model/46241-flexi-rex-with-stronger-links). I am using "Flexi-Rex-improved.stl" version in my make. There have been no alterations made to the Rex itself.


Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- No supports are needed.


Assembly
No adhesive is required. Friction fit. Print the Flexi-Rex separately using the link above.


_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

[REMIX] Flexi-Rex or Flexi-Dragon?

remix-flexidragon-eye-thewhatbrandsg.stl

remix-flexidragon-flame-inner-thewhatbrandsg.stl

remix-flexidragon-flame-outer-thewhatbrandsg.stl

I'm Ed, a maker and 3D printing enthusiast from Singapore. I enjoy creating gadgets, functional designs, and backpack hardware. Here to learn, seek inspiration, share and have an incredible time. =D

@TheWhatBrandSG

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

wined11

Achievements

Seedling

Fan Favorite

Explorer