A modular cable management device. Modular design allows volume expansion by stacking “cable-roll-ext-thewhatbrandsg.stl”.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5 (for strength).
- No supports are needed but follow the suggested print orientation for ideal results.

Assembly
The snap-on "Cap (cable-roll-cap-thewhatbrandsg.stl)" piece may be snug initially but should loosen up after a few rotations around the roll.

Changelog:
- 1 Jul 2024: Added a “Cap Ext” for use with one "cable-roll-ext-thewhatbrandsg.stl".

More designs on Printables: https://www.printables.com/@TheWhatBrandSG

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

Cable Organiser - Cable Roll

cable-roll-a-thewhatbrandsg.stl

cable-roll-ext-thewhatbrandsg.stl

cable-roll-cap-ext-thewhatbrandsg.stl

Modular cone design, you can achieve various sizes and functions by swapping different components - with more additional parts to be introduced later.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5 (for strength).
- No supports are needed but follow the suggested print orientation for ideal results.

Slight effort may be required when initially screwing the parts together. If you encounter tight threading, try threading the parts back and forth a couple of times before fully threading them in.

More designs on Printables: https://www.printables.com/@TheWhatBrandSG

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

Modular Traffic / Construction Cone (Tabletop Miniatures)

base-1-v3-thewhatbrandsg.stl

orange-3-v3-thewhatbrandsg.stl

A slim, portable design that easily fits in any pocket, holding 3 SD cards plus an attachment for Micro SD cards.

Suggested print settings for the **Main Body**:
- Layer height 0.2mm.
- Infill 20%.
- Perimeters: 5 (for strength and aesthetic).
- No supports are needed.

Suggested print settings for **Micro SD attachment**:
- Layer height 0.2mm.
- Infill 15%.
- Brim Width: 2mm.
- Brim Separation Gap: 0.2mm.
- No supports are needed but follow the suggested print orientation for ideal results.

More designs on Printables: https://www.printables.com/@TheWhatBrandSG

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

Minimalistic Card-sized SD Card Holder

sd-inner-thewhatbrandsg.stl

sd-microholder-bottom-thewhatbrandsg.stl

sd-microholder-top-thewhatbrandsg.stl

A Voronoi model remix of LXO's "[Lowest poly The Thinker](https://www.printables.com/model/1165-lowest-poly-the-thinker)".

Suggested print settings:
- Layer height 0.2mm.
- Infill 20%.
- Perimeters: 3.
- No supports are needed.
- Models in pictures are printed at 50% scale.

More designs on Printables: https://www.printables.com/@TheWhatBrandSG

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

[REMIX] The Thinker - Voronoi Edition

remix-thinker-v2-voronoi-thewhatbrandsg.stl

An "inviting" name/business card holder.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Supports are needed.
- Some post-support cleaning is required.

More designs on Printables: https://www.printables.com/@TheWhatBrandSG

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

Name Card Holder - Take One

namecard-holder-thewhatbrandsg.stl

Our take on the classic ACME-branded anvil. Any Road Runner fans in the house? Beep Beep.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- No supports are needed but follow the suggested print orientation for ideal results.
 
Assembly
The components fit together using a friction-fit mechanism. Push the base in until you feel a "click". Slight effort is needed to secure the components; use adhesive if necessary.

More designs on Printables: https://www.printables.com/@TheWhatBrandSG

NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise.

ACME Anvil (Tabletop Miniatures)

anvil-top-v2-thewhatbrandsg.stl

A sleek, compact and modular tray for small items designed for 2020 profiles. Modular design, utilise "2020-tray-centre-thewhatbrandsg" to extend the length of the tray.

Suggested print settings:
- Layer height 0.2mm.
- Infill 15%.
- Perimeters: 5.
- No supports are needed.


More designs on Printables: https://www.printables.com/@TheWhatBrandSG

NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise.

2020 Profile Slim Tray

2020-tray-centre-thewhatbrandsg.stl

remix-thinker-voronoi-thewhatbrandsg.stl

base-1-extension-v3-thewhatbrandsg.stl

base-1-mini-v3-thewhatbrandsg.stl

base-1-small-v3-thewhatbrandsg.stl

orange-5-v3-thewhatbrandsg.stl

white-2-v3-thewhatbrandsg.stl

white-4-v3-thewhatbrandsg.stl

cone-connector-thewhatbrandsg.stl

cable-roll-b-thewhatbrandsg.stl

cable-roll-cap-thewhatbrandsg.stl

anvil-base-v2-thewhatbrandsg.stl

anvil-tip-v2-thewhatbrandsg.stl

anvil-top-key-v2-thewhatbrandsg.stl

I'm Ed, a maker and 3D printing enthusiast from Singapore. I enjoy creating gadgets, functional designs, and backpack hardware. Here to learn, seek inspiration, share and have an incredible time. =D

More designs on [Printables](https://www.printables.com/@TheWhatBrandSG).

@TheWhatBrandSG

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

wined11

Pinned models

[REMIX] The Thinker - Voronoi Edition

Modular Traffic / Construction Cone (Tabletop Miniatures)

Cable Organiser - Cable Roll

ACME Anvil (Tabletop Miniatures)

Cable Organiser - Cable Roll

Modular Traffic / Construction Cone (Tabletop Miniatures)

Minimalistic Card-sized SD Card Holder

[REMIX] The Thinker - Voronoi Edition

Name Card Holder - Take One

ACME Anvil (Tabletop Miniatures)

2020 Profile Slim Tray