WELCOME TO HALLOWEEN DECORATION PART 1!

Since Halloween is suuper near I have prepared a series of models in order to have an amazing PINTING OCTOBER! 

To start this mini-series I present you my take on the super Famous Jack o'Lantern 

I have prepared 4 different models of faces for this one in order to have a bit or variety when decorating so it does not look repetitive. My personal fav is the one that has the eyes with different sizes by a lot, it simply looks amazing!

This print will use the little electric candles in order to create the light effect! As said, the set up is super easy and it is safe to use everywhere. I got mines from Temu but I am sure you can get them also in Amazon for super cheap!

You will also need 4 magnets 5x3mm per pumpkin in order to close them. This brings new opportunities because you can attach half of the pumpkin (with the candle inside) to ANYTHING MAGNETIC! Just let your creativity flowing, can't wait to see with people come up with!

MATERIAL LIST:
-Electric candle from Temu/Amazon
-4 5x3mm magnets per pumpkin

I used polymaker_3d filaments as always for that amazing final result! Sunrise orange and Army Dark Green just look amazing together don't you think?

Make sure to comment if you would like the same model but to use with real candles! I think it can be also a great addition for your home decor!

Do not hesitate to drop a follow because A LOT MORE MODELS ARE COMING SOON!!

Drop a like💜 really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

MAGNETIC JACK O' LANTERN

4.-Hollow_Pumpkin_Style_4_Fake_Candle(Magnet).3mf

Magnetic bees for kids designed as an activity. The idea is for the kid to match the color of the hive with the correct bee. They will love to play around with them, That I can ensure!

This activity is created for the kid to understand and match the colors without any explanation in a sense of exploring by themselves.

The idea of the magnets is for it to practice the pinching force that is needed to hold a pen/pencil when learning to write! There is a pincher added in the model but I have found that using a metallic one is way better for the little ones!

For this model you will need to use 20 magnets 10 x 4 mm (or smaller) that you can get from Amazon/Temu.

THIS ACTIVTY NEEDS TO BE SUPERVISED FOR SAFETY REASONS!

If you want to see this design in action Click the link ▶️: https://www.instagram.com/p/C-GAmn5N34f/?hl=en
Drop a like💜, comment 💬 it really helps us creators to get more done :D

**Buying this model does not grant access to sell it commercially, just for PERSONAL USE!**

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**Recommended settings for printing:**

NO SUPPORTS NEEDED FOR ANY PART!

MODEL IS  NOT SCALABLE since it is ready to add magnets (10 x 4 mm) at the bottom of the bees and petals. In total you will need 20 magnets!

Adhesion: Nothing is needed.

Layer height: 0,2 mm is more than enough

Infill: 5 - 10 %. Consider more if younger kids will play with it as the item can receive some damage. 

Post -Process: Bees, flowers and the hive come in parts and will need further assembly. This is super easy and straight forward to do with a bit of fast glue. You may also need to trim some little pieces to make everything fit but it is a super easy process to do!

MAGNETIC BEES FOR KIDS

3.-Hive_Complete_V2_(2cm_heith).stl

Come on let's be real. How many Benchys you have around? Yeah I figured. I am sure that they are just lying around...

Well this bundle of 3 different Benchy decoration that is about to change! Now you will be able to give the Benchys printed a better decorative look (specially your fist one in a new printer for example). This is an amazing print that will give a great touch on your 3d printable collection!

**In the files you will find:**
-The: Little wave decoration
-The Tsunami! decoration
-The: Oh S**t! KRAKEN! decoration
- EXTRA for THANGS DOWNLOADS: The tentacle on moving seas decoration. (this model is not featured as a picture and it is only to be found by the people that download the bundle. Little gift for you guys ;)

If you want to see this design in action Click the link ▶️:
https://www.instagram.com/p/C_s-E8yNsax/?hl=en

Drop a like💜, comment 💬 it really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**Recommended settings:**

MODEL IS NOT SCALABLE, LEAVE IT AS IT IS FOR FITMENT ISSUES!

Layer height:
-0.2 mm is perfect

-NO SUPPORTS ARE NEEDED FOR ANY OF THE MODELS

-No extra adhesion to the bed is needed

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

Benchy Boat Decoration Bundle

Benchy_Decoration_Style_3(Octopus).3mf

Are we dreaming?

Well.. now you have a way to check it with this awesome look alike inception totem. Similar style to the one used in the film!!

This one is designed to be a little Fidget to have on the desktop and make it spin endless times. It has an incorporated magnet (one at the base and another one at the totem) so it stays on the same spot while spinning. No one will know about the magnets, trust me ;)

It also works on any other surfaces if you do not want to use the base provided.

IMPORTANT: If you are not using a Bambulab Printer use the files with NO_PAUSES name. It seems that Cura slicer does not open the files with the pause setting.

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/ :)

**Recommended settings:**

-For this print it is recommended the use of magnets for weight and stability for the rotation of the totem. This print uses two 10x3 mm magnets for the base and the totem. The STLs have the pauses incorporated so you can add the magnet mid print and let the print continue to hide them!

-NO SUPPORTS NEEDED FOR ANY PART!

-MODEL IS SCALABLE but keep in mind the gaps for the magnets!!

-Adhesion: Nothing is needed.

-Layer height: 0,2 mm is more than enough

-Infill: 10 % is more than enough

INCEPTION MAGNETIC ROTOR

1.-Rotor_handle_no_pauses.stl

HEY HEY HEY LEAVE MY SWITCH IN PLACE!
This UFO (that is trying to steal my switch) is an amazing decoration made to enhance your gaming setup! This is an amazing way to prepare for Halloween and to keep after. The end product is amazing and I could not be happier for it!

The fitment is on point as well as the equilibrium with the machine installed. I designed it so the Switch is angled towards the left when looking it from the front. I can make it so that the UFO can go to the left if you have your switch at a place that needs it, just drop me a message on Instagram!

The print is divided in 3 parts. The UFO, the joiner and the Base. You will see that the Joiner can move in between the two parts in order to give enough space for the glue to not overflow when putting the 3 pieces together. Don't go crazy thinking your fitment is of!. It is super easy to print and even easier to assemble.

If you want to see this design in action Click the link ▶️: 
https://www.instagram.com/p/C_OF1D7NZW-/?hl=en
Drop a like💜, comment 💬 it really helps us creators to get more done :D

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

3D printing settings
MODEL IS NOT SCALABLE, LEAVE IT AS IT IS FOR FITMENT ISSUES!

Layer height:
-0.2 mm is perfect

-NO SUPPORTS ARE NEEDED

-No extra adhesion to the bed is needed

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

UFO SWITCH DOCK DECORATION

UFO.stl

Amazing High quality model of a V8 engine.

The engine shows only 2 of the 8 pistons in a V8 in order to see from the frontal part how the movement of the pistons are in a real engine.

The crankshaft moves with a lever attached to it at the back making the pistons go up and down.

Model has tight fit on all of the parts for a perfect finish, specially between the pistons and the block.

This can be used as a decoration item or to explain how an engine works!

(Model comes with a Wrench to tight all of the nuts)
(Use the pictures provided as instructions and contact me if more info is needed via DM without any issue!!)

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/ :)

3D printing settings
MODEL IS SCALABLE. It just depends on how big you want the final product to be. I printed mine at 50% and ended up being amazing.

Layer height: 0.2 mm or less for a higher quality

Supports: Some of the parts need supports because of the arches in STL 3.2 or overhangs in STL 3.1. Check your settings on supports and tweak it if needed.

Adhesion: No need of extra adhesion for any of the STLs.

Infill: 10% is more than enough.

PISTON ENGINE MODEL

3.1-Engine_Block_Printed_only_engine(1).stl


**ARTICULATED BUTTERFLY**

Here you will find 2 different STLs. One for the big butterfly (the wings are bigger) and a different one for the smaller version (wings are scaled down for a more cute look ;) ).

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**3D printing settings**
MODEL IS SCALABLE but check the slicing before printing to ensure the scale is enough to not fuse the articulations together (can end up happening if you scale down too much).

Layer height: here you have different options, all of them could be used:
-0.2 mm for a "not so detailed" final print. Use this only as final resource.
- 0.08 mm for a super detailed final print. This is the one I usually chose.
-You could also use the adaptative layer height on BambuStudio to combine the best of both worlds

NO SUPPORTS NEEDED!

Adhesion: I used a brim to prevent Warping but you should be safe without it.

Infill: 10% is more than enough.

ARTICULATED BUTTERFLY

Butterfly_Smaller_Wings.stl

Take aim, throw, and score!

Presenting the new portable mesh Dartboard! This is the needed piece in your desktop. Makes quite the decor touch as well as a good challenge. Perfect for a bit of entertaining during the long Home office hours. Who is up for it, will you be able to get the center?

What does the model include:

-This model comes with 2 options of Dartboard. A more minimalistic/clean one (with only the center painted as red) and another one more towards a more "realism" look.

-This model also includes the support that tilts the Dartboard that has storage for 2 darts.

-In the STL files you will also find the Dart. This has a special designed tip that is resistant to impacts (tested) since it is full plastic. The Dart has a "Rocket" style and can be placed Vertically also as decoration.

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/ :)

**3D printing settings**
Recommended settings:

-NO SUPPORTS NEEDED FOR ANY PART!

-MODEL IS SCALABLE

-Adhesion: Nothing is needed.

-Layer height: 0,2 mm is more than enough

-Infill: 10 %

IMPORTANT: To be printed at slower speeds than normal since the grid needs a lot of precision to be formed correctly. If you print at normal speeds the grid will not be a grid and the dart will not stay in.

PORTABLE DARTBOARD WITH DARTS

1.0.-Dartboard.stl

**DESERT ARTICULATED RATTLESNAKE (1.2 METERS)**

Check the mobility out HERE: https://www.instagram.com/p/C9xS7PKtwV7/?hl=en

Drop a follow if you want more content like this one ;)

This is a **SUUUPER** long and cute desert rattlesnake. As you can see, it can get up to 1.2 m (depending on your slice scale) on a 256x256 mm plate!

The model is amazing and super simple to print. It will be a little challenge for your clearance settings, see if you can print it (it is easy in the end don't worry ;) ).

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

3D printing settings
MODEL IS SCALABLE but check the slicing before printing to ensure the scale is enough to not fuse the articulations together (can end up happening if you scale down too much)!!

SPEED: I printed this at 50% speed on my printer to ensure the final result was amazing and it worked perfectly. Personally, I would not go too fast due to the high quantity of jumps the printer will have to perform. If you have small extrusion problems it will be visible so keep the speed down for this one!

Layer height: here you have different options, all of them could be used:
-0.2 mm for a "not so detailed" final print. Use this only as final resource.
- 0.08 mm for a super detailed final print. This is the one I usually chose.
-You could also use the adaptative layer height on BambuStudio to combine the best of both worlds

NO SUPPORTS ARE NEEDED!

Adhesion: I used a brim to prevent Warping but you should be safe without it.

Infill: between 5 - 10% is more than enough.

DESERT ARTICULATED RATTLESNAKE (1.2 METERS)

Desert_Snake_Articulated_Simplified_V2.3mf

An amazing print that will help you organize if you have more build plates than printers (like my case). It will case up to 6 build plates (256x256 mm). A must have if you possess ANY of the Bambulab printers!

This print can act as:

A Tripod: Specially useful if you have an A1 printer and space to flex on your build plates

A Side mount: If you have a P1S or any of the X1 series AND an AMS system. The AMS is necessary to side mount it since the weight of it will fix the plateholder (as counterweight).

This build does not use ANY GLUE (i did not use even one drop on mine) but could be a good addition if needed. Layer lines and how it is assembled will ensure that the final product does not snap!

USE THE PICTURES AS INSTRUCTIONS (it is super clear and easy) you can't miss it!

Any question regarding the model or how to assemble it can be sent to my Instagram DM: https://www.instagram.com/printplay.3d/

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

3D printing settings
-You will find STLs for all the pieces separately and the 5 together in case you want to to multicolor in a single color printer ;)

-MODEL IS NOT SCALABLE: Everything has been measured to a perfect fit!

-Layer height: here you have different options, all of them could be used:
   -0.2 mm for a "not so detailed" final print. Use this only as final resource.
   - 0.08 mm for a super detailed final print. This is the one I usually chose.
   -You could also use the adaptative layer height on BambuStudio to combine the best of both worlds

Supports ARE needed for one piece only. Normal and Automatic Bambulab supports works wonders then removing (when pliers are used) highly recommended

Adhesion: Nothing please, the use of brims will mess the perfect fit!

Infill: 15% is necessary on this one to ensure strength.

BUILD PLATE ORGANIZER FOR BAMBULAB

Bambulabs_SideMount_and_Tripod_Plateholder_5_Parts.3mf

Well the time to upgrade the coasters at your house but don't worry, I got you ;)

This amazing articulated coaster resembling tentacles from an octopus🐙. It will grab your mug so it does not go anywhere! ☕

Perfect to decorate part of your house or the part of your desktop designated to your mug while working/ designing

It is super easy to print. The Design comes in 2 different STLs (tentacles and the mug pad) in case you need to print in a different scale.

Drop a like💜, comment 💬 it really helps us creators to get more done :D

If you want to see this design in action Click the link ▶️: https://www.instagram.com/p/C98AWSaN-JK/?hl=en

Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

3D printing settings
MODEL IS SCALABLE for different mugs

Layer height:
-0.2 mm is perfect

-NO SUPPORTS 

No adhesion is needed

Infill: between 5 - 10% is more than enough.

ARTICULATED SELF ADJUSTING TENTACLE COASTER

Tentacle_Coaster_Tentacles.3mf

I wanted to do something that was both articulated and very flexible **AND magnetic**. Like this, the articulation could make it so the dragon would stick to **EVERYTHING, FLAT OR CURVED!**

This amazingly detailed dragon will do just that. It is **SUPER** flexible as you can see and will snap into anything metallic, **EVEN CURVED SURFACES** (following the curve line of the dragon). The details of the scales are truly amazing.

The dragon has a socket **for 51 5x3 mm magnets** in each body part. You can find pack of those in **Aliexpress or Temu (I used this ones)** with amazing prices over high quantities. You can get a lot of those because I will use this ones in the future for other articulated magnetic builds, you will love them ;).

Use a color changing filament for the finish I had. The print is **SUPER** easy and will print without any problems!

Drop a like💜, comment 💬 it really helps us creators to get more done :D

Do not hesitate to follow me on Instagram to be aware of the next upcoming Articulated Magnetic crafts! --> https://www.instagram.com/printplay.3d/


Buying this model does not grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram DMs: https://www.instagram.com/printplay.3d/

Articulated_Magnet_Dragon_V1.3mf

**LOW POLLY PANTHER INCENSE HOLDER**

I have been using incense sticks a lot lately but my holder was plain and boring... Too typical you know?

Well, presenting the Low Poly Panther incense holder to fix this 🐈‍⬛!
The model started as a customer request that wanted a low poly panther as decoration for the living room (full black style. While I was designing it i fell in love with the end product so decided to make some tweaks to make it be an incense holder.

Prints SUPER easy even when using supports (Bambulab supports are just🤤). The final product needs assembly but it is super easy and SUPER fast (you have a couple of gifs showing how). The idea is to NOT glue the two parts of the tail together so they will hold the incense stick, works perfectly!

The finish is simply amazing and I couldn't be happier with it, it was a great call to convert the decorative with the useful touch.

The filament I used on the different panthers:
-Polymaker Army Dark green
-Polymaker Starlight Jupiter
-Esun PLA silk magic (green/blue)

Drop a like💜, comment 💬 it really helps us creators to get more done :D
Do not hesitate to follow me on Instagram to be aware of the next upcoming Articulated Magnetic crafts! --> https://www.instagram.com/printplay.3d/

Buying this model DOES NOT grant access to sell it commercially, just for PERSONAL USE!

Any question regarding the model can be sent to my Instagram DMs: https://www.instagram.com/printplay.3d/

**3D printing settings:**
-MODEL IS SCALABLE BUT SCALE BOTH PARTS THE SAME!

Layer height:
-0.2 mm is more than sufficient but you could go for less (0.08) to have an amazing finish on the curved surfaces

-SUPPORTS ARE NEEDED. I used the normal supports from Bambulab (Automatic ones) and it turned out to be perfect. The removal is super easy and does not affect the size for the joiners.

-No extra adhesion is needed

-Infill: between 5 - 10% is more than enough. I printed mine with 5%

LOW POLLY PANTHER INCENSE HOLDER

1.-Body_and_Joiners.3mf

**OCTOPUS SWITCH DOCK**
It was time to upgrade my old Switch dock version. Nothing wrong with that but as the designs that I upload I like to be constantly moving with new things! This is why I ended up making this octopus Switch docker! **Perfect to decorate part of your gaming place!**

This octopus design 🐙 is amazing and SUPER realistic. The fitment is on point as well as the equilibrium with the machine installed. I designed it so the Switch can go inside both ways. This is because like this you can angle it both ways, better for decoration ;)

It is super easy to print but will take some time SO BE PATIENT, IT WILL BE WORTH IT.

The Design comes with 2 different STLs (2 for the price of one,) the grabbing one and the one that suspends the Nintendo in the air.

If you want to see this design in action Click the link ▶️: https://www.instagram.com/p/C-GAmn5N34f/?hl=en
Drop a like💜, comment 💬 it really helps us creators to get more done :D

**Buying this model does not grant access to sell it commercially, just for PERSONAL USE!**

Any question regarding the model can be sent to my Instagram: https://www.instagram.com/printplay.3d/

**3D printing settings**
MODEL IS NOT SCALABLE, LEAVE IT AS IT IS FOR FITMENT ISSUES!

Layer height:
-0.2 mm is perfect

-SUPPORTS ARE NEEDED FOR BOTH STYLES

-No extra adhesion to the bed is needed

-Infill: between 5 - 10% is more than enough. I printed both with 5%

OCTOPUS SWITCH DOCK DECORATION

Octopus_Sculpted_Switch_Docker_V2_Painted.3mf

<p dir="ltr"><span style="white-space: pre-wrap;">Halloween designs coming out soon ;)</span></p>

Get ready!

Unlock all of the Printplay3D models posted!

**Features:**
Discover a wide range of models suitable for beginners to advanced builders and printers. In this plan you will find multiple types of models, from switch dockers, articulated prints and many others!
Members will have 3 downloads per month on all the models I post, choose wisely!

**Benefits:**
Enjoy new models ensuring your creative pursuits stay fresh and exciting. 
Subscribe today and start building your creativity!

**Other information:**
- All my models are printed before upload to make sure the piece is as intended!
- Feel free to drop me a message on Instagram if something is needed (Instructions, custom parts, custom modifications etc..)
- **IMPORTANT: ALL of the models are for private use only**

Printplay Models!

1.-Rotor_Handle_with_pauses.3mf

2.-Rotor_Suport_with_pauses.3mf

2.-Rotor_Support_no_pauses.stl

Benchy_Decoration_Style_1(Wave).stl

Benchy_Decoration_Style_2(Tsunami).stl

Benchy_Decoration_Style_4(Octopus_V2).stl

1.-Wings_eyes_joiner_Bees_(10_units.3mf

2.-Body_Bee_with_color.3mf

3.-Centrer_flower.stl

4.-Joiner_flower.stl

5.-Petal_flower.stl

Hive_bot_Part1.stl

Pincher.stl

1.-Hollow_Pumpkin_Style_1_Fake_Candle(Magnet).3mf

2.-Hollow_Pumpkin_Style_2_Fake_Candle(Magnet).3mf

3.-Hollow_Pumpkin_Style_3_Fake_Candle(Magnet).3mf

5.-Hollow_Pumpkin_Style_4_Fake_Candle(Magnet).3mf

Hello! I am Printplay3D. I design and Print things, hope you like my models :)
Find me here: https://www.instagram.com/printplay.3d

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Printplay3d

Achievements

Seedling

Designer posts

Get ready!

Pinned models

INCEPTION MAGNETIC ROTOR

Benchy Boat Decoration Bundle

MAGNETIC BEES FOR KIDS

MAGNETIC JACK O' LANTERN

MAGNETIC JACK O' LANTERN

MAGNETIC BEES FOR KIDS

Benchy Boat Decoration Bundle

INCEPTION MAGNETIC ROTOR

UFO SWITCH DOCK DECORATION

PISTON ENGINE MODEL

ARTICULATED BUTTERFLY

PORTABLE DARTBOARD WITH DARTS

DESERT ARTICULATED RATTLESNAKE (1.2 METERS)

BUILD PLATE ORGANIZER FOR BAMBULAB

ARTICULATED SELF ADJUSTING TENTACLE COASTER

Articulated_Magnet_Dragon_V1.3mf

LOW POLLY PANTHER INCENSE HOLDER

OCTOPUS SWITCH DOCK DECORATION