ABOUT:

This holds a standard oil filter socket.

Shout out to https://gridfinity.perplexinglabs.com/ for the assist as always.

 

FEATURES:

Keep all your socket tools and accessories together.

It's for a standard oil filter.

Anyone looking for this exact adapter will be useful.

 

PRINTING SUGGESTIONS: 

I would use PLA, 

It shouldn't take more than 1hr to print.

I would do 10-15% infill. 

No brim is needed because of the large print surface. 

 

License CC BY-NC-SA Soldering Base by scupoli is licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license.


FINAL THOUGHTS:

Maybe someone will find this useful.

Cheers!

Visit my blog: https://www.scwd.us

Visit my YouTube Channel: https://www.youtube.com/c/scwooddesigns


Oil Socket.stl

ABOUT:

Looked all over and couldn't find a specific size for my wrenches.  So I made it.

Shout out to https://gridfinity.perplexinglabs.com/ for the assist as always.

I left the socket slots without sizes so it could be customized. 

 

FEATURES:

Keeps all the wrenches and driver together.

It's for a mini ¼" Husky set and a 3/8" Tactix wrench and ¼" driver set.

Anyone looking for this exact wrench it will be useful.

 

PRINTING SUGGESTIONS: 

I would use PLA, 

It shouldn't take more than 1hr to print.

I would do 10-15% infill. 

No brim is needed because of the large print surface. 

 

License CC BY-NC-SA Soldering Base by scupoli is licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license.


FINAL THOUGHTS:

Maybe someone will find this useful.

Cheers!

Visit my blog: https://www.scwd.us

Visit my YouTube Channel: https://www.youtube.com/c/scwooddesigns

Tactix_Husky_Rachet Holder.stl

**ABOUT:**
Didn't want to fuss with Gridfiniy and all the magnets.

**FEATURES:**
The large round 46mm insert is for a 8.oz Lucas White Lithium Grease
The medium 43mm insert are for a 4.oz liquid Super Lube. 
The smaller 34mm insert is for a 2.oz Starbond super glue.
The small 32mm inserts are for 1.oz needle bottles, and a 60.mL Bambu Lab Liquid Glue.
The long horizontal insert is for a standard 7g/0.24 oz glue stick.
There are also inserts for the StarBond Glue's nozzles, pin cap, and lid.
 
**HARDWARE NEEDED: **
(4)  13 mm rubber feet for anti-skid purposes. 

**PRINTING SUGGESTIONS: **
I would use PLA.
It shouldn't take more than 3 Hours.
I would do 10 Hex pattern infill.
Supports are optional for the feet holes on the bottom. 
No brim is needed because of the large print surface. 

**DISCLOSURES:**
No accessories included. 

**FINAL THOUGHTS:**
Maybe someone will find this useful.

Cheers!

Visit my blog: https://www.scwd.us

Visit my YouTube Channel: https://www.youtube.com/@SCWD_US

✖ | Sharing without ATTRIBUTION
✔ | Remix Culture allowed
✖ | Commercial Use
✖ | Free Cultural Works
✖ | Meets Open Definition

Chemical Holder.stl

ABOUT:

Made some anti-skip feet for my pancake compressor that lives on a wooden board under my metalworking bench. Most people keep it under a work bench of some kind. Hopefully it's wood.

This will work with any pancake style compressor's feet. Porter Cable, Craftsman, Ryobi, etc…

If you need another diameter for yours, I can help out. 

I only have one pancake compressor so I don't know what sizes are out there. 



FEATURES:

Keeps the compressor in one place without skipping. Will accommodate a bolt or screw depending on what size you need. (5mm or 10mm). The feet have an ID of 40mm. 



HARDWARE NEEDED: 

(3)  5mm or 10mm  ¾" or 1" long fasteners. 



PRINTING SUGGESTIONS: 

I would use PLA, TPU 95a, or ABS. Basically anything shock resistant.

It shouldn't take more than 1hr to print all three. 

I would do 10-15% infill. 

No brim is needed because of the large print surface. 

License
CC BY-NC-SA
Soldering Base
by scupoli is licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license.

FINAL THOUGHTS:

Maybe someone will find this useful.

Cheers!

Visit my blog: https://www.scwd.us

Visit my [YouTube Channel](https://www.youtube.com/@SCWD_US)

Pancake Anti-Skip Feet

compressor anti vibration feet 10mm.stl

**My Soldering Base UPDATE: 09/18/2024**
Added V2 with lips to the tip, heat shrink tube, and solder flux inserts.
Solder Flux insert ID is 32mm. (For a smaller flux liquid container)
New design is for added support and to prevent anything from falling out.

**My Soldering Base UPDATE: 09/14/2024**
*Added (6) 13mm Anti-Skid feet inserts.
* Added (4) 7mm HAKKO Tip Inserts
* Redesigned the holder adding more girth to the knobs. (Not Included)
* Added Wire Helper. (Not Included)
Enjoy

**ABOUT:**
Made a custom soldering base with a detachable piece of 23guage sheet metal (165mm x 114mm) held on by 10mm x 3mm magnets.
I put some electrical tape around the perimeter or the sheet metal to help with grip and mainly to not cut anyone that uses it.
I've tested this and it does not melt the base plate.
Time will tell.

**FEATURES:**
The large round 44mm hole fits 1 of 3 things. A tiner, flux paste, or electrical tape.
The (4) 7mm inserts are for HAKKO Soldering tips. 
The square hole will hold your tips or heat shrink tubes.
Fits a piece of 23guage sheet metal @ 165mm x 114mm.
(6) 13mm rubber anti-skid feet inserts
 
**HARDWARE NEEDED: **
(1)  3mm x 12 bolt, washer, and nut. The nut is held in place on the bottom. 
(4) neodymium/rare earth magnets @ 10mm x 3mm. 
(Optional) Electrical black tape around the perimeter of the sheet metal for grip and protection.

**PRINTING SUGGESTIONS: **
I would use PETG, ASA, or ABS for heat resistance.
It shouldn't take more than 40 mins or so to finish the print.
I would do 10-15% Hex pattern infill.
Supports are optional for the nut hole on the bottom. 
No brim is needed because of the large print surface. 

**DISCLOSURES:**
Shown with optional solder spool holder. 
No accessories included. 


**FINAL THOUGHTS:**
Maybe someone will find this useful.
Cheers!

Visit my blog: https://www.scwd.us
Visit my YouTube Channel: https://www.youtube.com/@SCWD_US

**License
CC BY-NC-SA
Soldering Base
by scupoli is licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license.**

Soldering Base

solder plate final.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

SCWD

Achievements

Seedling

Oil Socket.stl

Tactix_Husky_Rachet Holder.stl

Chemical Holder.stl

Pancake Anti-Skip Feet

Soldering Base