AT60ED Autofocus and Support parts

scope support bottom.stl

Tiefladewagen Kontainer Märklin 4618.stl

Easter Bunny Stencil

Bunny Stencil.stl

Easter Bunny egg

BunnieOpen.stl

SCX24 Battery holders

SCX24 stock battery holder.stl

Christmas Light Hooks.stl

This is a hook for hanging Christmas lights without drilling. I wanted something small and low-profile that would hold the cord of a strand of Christmas lights without letting it slip out if they got jostled. Works with a strip of thin 0.4 inch or 1cm wide double-sided tape.

yarn_bowl_wsupports.stl

Remix of yarn bowl with supports added in Mesh Mixer - lower -3mm on z axis to make flush with build plate

ZigZag Christmas Ornament

##Not to Be Sold
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

##About the Design
This is an elegant abstract sculpture masquerading as a Christmas ornament. It almost seems to change shape as you rotate it in different directions.

This ornament prints well with just a single perimeter. That makes it very light and lets the most light through is you use transparent/translucent filament. In fact, it positively glows. It also looks amazing printed with bichromatic or trichromatic filaments. 

The print shown in clear was printed with Matterhackers Transparent PLA. They were printed on an AnyCubic Mega S and sliced using Cura. I'll be adding pictures soon that show the ornament printed with Matterhackers Quantum Raspberry Gold and Translucent Blue printed on a Prusa MK3S+ sliced using PrusaSlicer.

##Resizing
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

##Print Time
About 5 hours

##Print Settings
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 mm.

*Infill*
Using PrusaSlicer, you won't need infill. Just set top and bottom to 1 layer and minimum shell thickness to 0.15 mm. That will keep the ornament light (about 13 grams) and will let the most light through if you use translucent/transparent PLA. 

If you use Cura, I would use support blockers set to 1-3 layers high to add infill just in those areas that are unsupported.

*Speed*
With PrusaSclier, I used the default speed settings for my printer and generic PLA. In cura, I used:
* Outer Wall: 35 mm/sec
* Inner Wall: 40 mm/sec
* Travel Speed: 60 mm/sec

*Build Plate Adhesion*
I used a brim. With the supports, you shouldn't need a raft.

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. If you get supports inside the ball, just add a support blocker.

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 60 Degrees (Cura) and 67 (PrusaSlicer)

Gridfinity: Ricoh DB-110 Battery Holder for GR3(x)

Ricoh DB-110 Battery Holder for Ricoh GR3 and GR3x for [Gridfinity](https://gridfinity.xyz) system.

bike.stl

Dog Food Scoop.stl

I needed a new scooper for my dog food. It holds about .5 cups or around 125ml

Parrot cage accesoreis

food and water hanger.stl

RFID Cat Feeder

Base.stl

Camera (model 2), nestable box (v1)

Easter Bunny with Basket

Easy to print Easter Bunny with a basket on its back large enough to hold a cadbury egg. Prints without supports on most printers

Bike Wall Mount

Pedalmount.stl

Pickle Christmas Tree

A pickle Christmas Tree ornament. 

No supports needed to print.

Safety Axolotl 

A 3d printed axolotl that will not be the same as walking on legos when your kid leaves it on the floor.  

Fluval 3.0 10mm rimless tank riser.stl

Was unable to find a light riser for the Fluval Plant 3.0 lights that would fit on a 10mm rimless aquarium, so I fabricobbled this up. It's rises the light roughly 10cm/ 4". Nothing special as far as the print goes, I printed it laying flat to reduce the amount of supports needed. Requires two risers per light. Hope this helps someone else!!

hobbies & leisure

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

AT60ED Autofocus and Support parts

Tiefladewagen Kontainer Märklin 4618.stl

Easter Bunny Stencil

Easter Bunny egg

View 14 new models

Christmas Light Hooks.stl

yarn_bowl_wsupports.stl

ZigZag Christmas Ornament

Gridfinity: Ricoh DB-110 Battery Holder for GR3(x)

bike.stl

Dog Food Scoop.stl

Parrot cage accesoreis

RFID Cat Feeder

View 468 new models

Easter Bunny with Basket

Bike Wall Mount

Pickle Christmas Tree

Safety Axolotl

Fluval 3.0 10mm rimless tank riser.stl

Ashford traditional bobbin