Marine Engine

smile vase

EZPZ Cable Clip

Keep cables from slipping off your desktop with this simple clip. Just stick some [double sided VHB tape](https://amzn.to/47Ipbyn) on the bottom to affix it to your work surface. For cables up to 4mm in diameter.

Photographed model printed with [Qidi CF-Nylon filament](https://amzn.to/403NySk), but most filaments should work fine.

NIGHT TABLE

MODERN BEDSIDE-BODY

Universal Laptop Under Desk Holder

Marsgizmo - Laptop Under Desk Holder - Assembly View.step

Hex Tray / Bin / Basket

Remix of Dryer door magnetic Holder

I was being slightly lazy with a bad back and a free printer, so I whipped up a design to hold the dryer door open while doing laundry. I printed it with some PETG remnants because I dont like to be wasteful, so don't mind the multicolored part haha. I designed this to use a single trace on the upright portion so it does not need supports around the magnet holes. It had a big flat surface just screaming for a logo, so I obliged.

It uses (7) 12mmx3mm magnets, and seems like it will do the trick.

I hope others find this useful!

Happy printing!

Dryer door magnetic Holder

1x2 grifinity bin.stl

just a 1x2 grifinity bin but "wrong" since it doesn't have a slot to fit the "real" grid 

Mandalorian Helmet

mandobase.3mf

Square Divided Vase/Container

I was looking for the perfect vase/holder for my favourite3D Printed flowers, and came up with this design with convenient dividers.
 
    This model is not meant to be printed in vase mode. It is a vase/holder, but has dividers inside to keep everything organized!
    Play with colour swaps and change the size for your use!
    You can also use this as a desktop pen holder, a bathroom counter organizer and much more – have fun!




Sushi Restaurant

body

Blender_Bottle_Go Stak

USB_Extensions_Mount

XYZ_CallibrationCube.stl

This is a small and simple XYZ calibration cube for checking the dimensional accuracy of your printer.   The cube has X, Y and Z written along their respective axes.

Once printed either use an accurate ruler or callipers to measure the dimensions of the print. The original model size is 20mm*20mm*20mm however you may wish to resize it to be bigger (or smaller). 

Once you have measured your dimensions you may want to adjust the steps or steps per mm for each axis in your printers firmware - This may or may not be possible depending on your printer. 

To do this you will need to find your current Steps per mm, and then have your observed dimension and expected dimension.

To calculate the new Steps per mm you will need to do:

(Expected/Observed)*Current Steps per mm = New Steps per mm

It is also good as just giving a gauge of how well your 3D printer works with small over hangs and flat faces to check for Z-Banding or ghosting!

PUNISHER - KEYCHAIN

Punisher_Keychain.stl

Foosball Flinger // Table Soccer Corner Mod

Upgrade your foosball table with these corner mods that launch the ball into the air and back into play! 

Made for a table with walls roughly 110mm tall. You may need to adjust the scale for your own table to properly fling the ball back into the field.

Table

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Marine Engine

smile vase

View 111 new models

NIGHT TABLE

View 15 new models

Hex Tray / Bin / Basket

Remix of Dryer door magnetic Holder

1x2 grifinity bin.stl

View 202 new models

Square Divided Vase/Container

Sushi Restaurant

Blender_Bottle_Go Stak

USB_Extensions_Mount

View 16 new models

PUNISHER - KEYCHAIN

View 72 new models

Simple Box

curved table.stl

SPOOL HOLDER OPTIMIZED

Spinner