Cathedral Christmas Bulb 2024

Cathedral Bulb.stl

Hangable Christmas Jolly Santa Turtle

Hangable-Jolly-Turtle-RebelAlicornDesigns.stl

Christmas Hippopotamus Ornament 

Hippopotamus.3mf

Christmas Dragon Egg 2025 

Christmas dragon egg base.stl

Christmas Balls with Integrated Stems

Semi-Open Ball with Integrated Stem.stl

Santa Bones

Resting Skeleton.stl

Diamond Christmas Ball Design 2

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems. It may be a little challenging to print. The key is to get the speed, temperature and flow right for your particular printer/filament combo so the stem prints cleanly at the narrowest point.

I printed this in Matterhackers Translucent Red. It's a nice balance between translucency and reflectivity. For an opaque filament, I'd use a multi-color PLA (like Matterhackers Quantum) or a medium toned silky PLA (gold, red, just use anything that's not really light or dark). Either type of filament would show off the facets nicely.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 110, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm and adding custom settings for the base of the ball that printed it 0.8 mm thick. You can do this by adding a support blocker to the bottom and giving it custom settings of 0.4 mm. Cura adds the two and prints the area within the blocker at 0.8 mm.

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I really relied on the supports for build plate adhesion. I used a brim, but I set it to 3.2 mm gap from the print so it would touch the supports but not the ornament.

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
Support Overhang Angle: 45 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 m above the build plate so that the supports would only be added to the bottom of the ornament.

Cathedral Christmas Stretch Ornament 2024

Stretch Cathedral.stl

Closed Lattice Christmas Bell

This is the third in this year's Christmas bell series. It prints quickly ad easily. Use a nice medium toned silky, metallic or multicolored filament to show off the geometry - or use translucent filament to make it glow.

This is based on my spiral and open lattice bells. It's roughly the same size (slightly taller) with a new loop at the top and a new lattice pattern. 

###Not to be Sold
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

*** PRINT SETTINGS***
* Walls: 0.4 - 0.8 mm (I used 0.4 mm for the clear bell and added an alternating extra line for the opaque bell)
* Layer Thickness: 0.15 mm recommended. Anything from 0.1 - 0.2 mm should look good.
* Infill: None. Seriously. It doesn't need it. It just adds weight and print time.
* Rafts/Brim: I didn't use either. However, the first layer is just a single width circle, so you may need to add a brim or raft.
* Supports: None. I designed this to print cleanly without them.

Open Lattice Christmas Topper

open lattice topper no supports.stl

Christmas Ornament Gingerbread Girl / Woman with Bow

Gingerbread Woman Ornament.stl

Swoop 3 Christmas Finial 2024

Finial Swoop 3 Whole v2.stl

Boba Fett Christmas Tree Decoration

This is a Boba Fett Helmet Christmas Tree Decoration. You can find his rival and friend The Mandalorian here: [The Mandalorian Christmas Tree Decoration](https://thangs.com/designer/frikarte3D/3d-model/The%20Mandalorian%20Christmas%20Tree%20Decoration-567052?manualModelView=true)
It's designed to be printed in different color changes to achieve the final result, if you want you can print it in one color and paint later.
This is the filament color change configuration if you print with 0.2mm layer:
0 to layer 13 (0 to 2.6mm) = Green
14 to 17 (2.8 to 3.4mm) = Black
18 to 21 (3.6 to 4.2mm) = White
22 to 25 (4.4 to 5mm) = Red

ALL Frikarte3D designs are protected by the Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or print models of my designs without my explicit written consent.

To sell them legally, message me so we can work out a deal.

Hope you like it! Any advice, or recommendation is welcome! Happy Printing!

I would be very grateful if you print it and put it on social networks to tag me at [@Frikarte3D](https://www.instagram.com/frikarte3d/)

Sh-Elf SPLIT Male 

sh-elf hat.stl

Royal Crown Christmas Teardrop Ornament

Royal Crown Teardrop Christmas Tree Ornament.stl

Ornamental Bauble 2023 (#1)

Ornamental Bauble 2023_#1.stl

Knitted Star Wars Grogu Figurine / Ornament / No Supports / Multiparts / 3MF Included

Christmas Ornament

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Cathedral Christmas Bulb 2024

Hangable Christmas Jolly Santa Turtle

Christmas Hippopotamus Ornament

Christmas Dragon Egg 2025

Christmas Balls with Integrated Stems

Santa Bones

Diamond Christmas Ball Design 2

Cathedral Christmas Stretch Ornament 2024

Closed Lattice Christmas Bell

Open Lattice Christmas Topper

Christmas Ornament Gingerbread Girl / Woman with Bow

Swoop 3 Christmas Finial 2024

Boba Fett Christmas Tree Decoration

Sh-Elf SPLIT Male

Royal Crown Christmas Teardrop Ornament

Ornamental Bauble 2023 (#1)

Knitted Star Wars Grogu Figurine / Ornament / No Supports / Multiparts / 3MF Included

Winter Veil Vase for Christmas Decor

Overly Excited Reindeer Christmas Ornament

Gingerbread Man - Formal Bowtie