This is an enclosure based around my (vague) memory of the Amiga PSU's (I also have one for Amiga 500/600/1200's).  This enclosure is designed to house a Meanwell RT-50B power supply (+5V/+12V/-12V_, and includes cut outs for an IEC connector (aka Kettle cord) and a switch.

Print the lid with the top down, the base with the bottom down, the cable clamp with the "grip" up and the logo plate however you'd like.  Use supports with an XY separation of 1.2+mm (so it doesn't put supports in the vent - the vent will print without supports just fine).

And please post makes!!!

The extra parts needed are (as near as I can tell - I bought my parts from Jaycar in Australia - though they didn't have the 4 pin DIN):

4 x [Large screws (Join lid to base)](https://amzn.to/3YFyf3h)
2 x [Small screws (For cable clamp)](https://amzn.to/3UHEEK4)
1 x [IEC Socket](https://amzn.to/3NVz3vU)
1 x [240V - 10A Switch](https://amzn.to/3YXO72g)
1 x [CD32 4 pin DIN](https://amzn.to/3CguWrv)
2 x [Mainboard Screws](https://amzn.to/4eoD32J)
1 x [Meanwell RT-50B](https://amzn.to/3YX4GeK)
4 x [Rubber feet - 12mm](https://amzn.to/4hxXKfv)

Amiga 500/600/1200 PSU Enclosure - Meanwell RT-50B

A1200_PSU_Top.stl

This is an enclosure based around my (vague) memory of the Amiga PSU's (I also have one for Amiga 500/600/1200's).  This enclosure is designed to house a Meanwell RD-35A power supply, and includes cut outs for an IEC connector (aka Kettle cord) and a switch.  The switch isn't really necessary for the CD32 - but I like saving a bit of power by turning my powersupplies off.

Print the lid with the top down, the base with the bottom down, the cable clamp with the "grip" up and the logo plate however you'd like.  Use supports with an XY separation of 1.2+mm (so it doesn't put supports in the vent - the vent will print without supports just fine).

And please post makes!!!  I had about 3 goes at printing a red version (in pics) - but the lid kept stuffing up.  I think (a) it's dodgy filament and (b) my PEI might need a wash.  Worked fine in black - so I'm blaming the filament.

The extra parts needed are (as near as I can tell - I bought my parts from Jaycar in Australia - though they didn't have the 4 pin DIN):

4 x [Large screws (Join lid to base)](https://amzn.to/3YFyf3h)
2 x [Small screws (For cable clamp)](https://amzn.to/3UHEEK4)
1 x [IEC Socket](https://amzn.to/3NVz3vU)
1 x [240V - 10A Switch](https://amzn.to/3YXO72g)
1 x [CD32 4 pin DIN](https://amzn.to/3CguWrv)
2 x [Mainboard Screws](https://amzn.to/4eoD32J)
1 x [Meanwell RD-35A](https://amzn.to/4hFCCnt)
4 x [Rubber feet - 12mm](https://amzn.to/4hxXKfv)

Amiga CD32 PSU Enclosure - Meanwell RD-35A

CD32_PSU_Top.stl

Make 3D printing great again...A random idea I had.  Includes a Lithophane of quite possibly the most famous person in the world at the moment.

Includes a handy frame to help keep your favourite Felon exactly where he should be.

Lithophane is 10cm x 10 cm.  Frame is a 1 cm border.

I printed the Lithophane standing upright, aligned with the Y axis, 0.12mm slices, 99% fill - white PLA (from the sample that came with my Creality 3 Max Neo).

I printed the frame laying flat from Black PLA.  I increased the bottom layer thickness to 2mm - though I probably didn't need to.

Trump - Lithophane

CE3MAXNEO__130896818_donaldtrumpfullmugshot.3mf

Sample for the cleat hanging system.  This system currently contains a shelf system, cups (e.g. Spice rack) and hooks.  It also includes some useful tools to assist with the installation of the cleats.

See the PDF for a description of each of the components and how to install/print each.

This sample includes the 20mm cleat with the "Strong" hook.

Sample - Cleat based hanging system

Strong_Hook_002.stl

This system currently contains a shelf system, cups (e.g. Spice rack) and hooks. It also includes some useful tools to assist with the installation of the cleats.

See the PDF for a description of each of the components and how to install/print each.

This collection contains the various cups from 20mm to 120mm internal diameter in steps of 5mm.  See the instructions for the different types of cups.  The name of each file indicates the cup type (Plain, Snug, Close Left/Right/Both).

Cups - Cleat based hanging system

Cup_Snug_25mm.stl

This system currently contains a shelf system, cups (e.g. Spice rack) and hooks. It also includes some useful tools to assist with the installation of the cleats.

See the PDF for a description of each of the components and how to install/print each.
This collection of STL's contains the actual cleats.  They are named as follows:

Cleat_<Type>_<Length>_<Holespacing>

The hole spacing refers to the maximum distance between the screw holes.  The holes will be evenly spaced and the number of holes is determined by how long the cleat is combined with the maximum distance.  For example with a 280mm long cleat, if the maximum distance between holes is 150mm then the cleat will have 3 holes and the spacing between those holes will be 130mm.  The end holes are 10mm from the end - leaving 260mm.

Once you have your cleats you need accessories such as the Shelves, Cups or Hooks.

Cleats - Cleat based hanging system

Cleat_Plain_340mm x 60mm.stl

Cleat_Plain_200mm x 200mm.stl

Cleat_Both_60mm x 60mm.stl

Cleat_Both_80mm x 60mm.stl

Cleat_Both_100mm x 60mm.stl

Cleat_Both_100mm x 100mm.stl

Cleat_Both_120mm x 60mm.stl

Cleat_Both_120mm x 100mm.stl

Cleat_Both_140mm x 60mm.stl

Cleat_Both_140mm x 150mm.stl

Cleat_Both_160mm x 60mm.stl

Cleat_Both_160mm x 100mm.stl

Cleat_Both_160mm x 150mm.stl

Cleat_Both_180mm x 60mm.stl

Cleat_Both_180mm x 100mm.stl

Cleat_Both_180mm x 200mm.stl

Cleat_Both_200mm x 60mm.stl

Cleat_Both_200mm x 100mm.stl

Cleat_Both_200mm x 200mm.stl

Cleat_Both_220mm x 60mm.stl

Cleat_Both_220mm x 100mm.stl

Cleat_Both_220mm x 200mm.stl

Cleat_Both_240mm x 60mm.stl

Cleat_Both_240mm x 100mm.stl

Cleat_Both_240mm x 150mm.stl

Cleat_Both_240mm x 300mm.stl

Cleat_Both_245mm x 60mm.stl

Cleat_Both_245mm x 100mm.stl

Cleat_Both_245mm x 150mm.stl

Cleat_Both_245mm x 300mm.stl

Cleat_Both_260mm x 60mm.stl

Cleat_Both_260mm x 100mm.stl

Cleat_Both_260mm x 150mm.stl

Cleat_Both_260mm x 300mm.stl

Cleat_Both_280mm x 60mm.stl

Cleat_Both_280mm x 100mm.stl

Cleat_Both_280mm x 150mm.stl

Cleat_Both_280mm x 300mm.stl

Cleat_Both_300mm x 60mm.stl

Cleat_Both_300mm x 100mm.stl

Cleat_Both_300mm x 150mm.stl

Cleat_Both_300mm x 300mm.stl

Cleat_Both_320mm x 60mm.stl

Cleat_Both_320mm x 100mm.stl

Cleat_Both_320mm x 150mm.stl

Cleat_Both_320mm x 300mm.stl

Cleat_Both_340mm x 60mm.stl

Cleat_Both_340mm x 100mm.stl

Cleat_Both_340mm x 150mm.stl

Cleat_Both_340mm x 200mm.stl

Cleat_Both_360mm x 60mm.stl

Cleat_Both_360mm x 100mm.stl

Cleat_Both_360mm x 150mm.stl

Cleat_Both_360mm x 200mm.stl

This system currently contains a shelf system, cups (e.g. Spice rack) and hooks. It also includes some useful tools to assist with the installation of the cleats.

See the PDF for a description of each of the components and how to install/print each.

This collection contains the various parts for the shelving.  See the instructions for the shelf styles available.

Shelves - Cleat based hanging system

Shelf_Hex_160mm.stl

This system currently contains a shelf system, cups (e.g. Spice rack) and hooks. It also includes some useful tools to assist with the installation of the cleats.

See the PDF for a description of each of the components and how to install/print each.

This tool can be used to mark where to drill for the holes in the cleats. 

Hole Marker - Cleat based hanging system

Hole_Marker_Body_v1.stl

This system currently contains a shelf system, cups (e.g. Spice rack) and hooks. It also includes some useful tools to assist with the installation of the cleats.

See the PDF for a description of each of the components and how to install/print each.

This is a wall plug that can be used to attach the cleats to Plaster (Dry Wall) walls.

Wall Plug - Cleat based hanging system

WallPlug_v6.stl

This system currently contains a shelf system, cups (e.g. Spice rack) and hooks. It also includes some useful tools to assist with the installation of the cleats.

See the PDF for a description of each of the components and how to install/print each.

This is the spacer that makes setting uniform distances between rows of cleats easy.

Spacer - Cleat based hanging system

Cleat_Spacer_Body_v2_30cm.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

ssouthur

Achievements

Seedling

Voyager

Novice Maker