IKEA hook.stl

arduino nano case .stl

nano case1 .stl

Problem - design - solution.stl

banner.stl

Lychee fruit shaped pot mold 

Liczi mold (with extra screw holes).stl

1:4 reduction bevel gear assembly Nema17.stl

assembly example.stl

Drive rack.stl

drawing tablet wall mount.stl

tablet holder.stl

Soldering wire stand (Print in place)

Really proud of this one. Soldering wire stand with print in place hinge and metal shaft slid into a hole. supports most sizes of soldering wire spools, many spools can be installed at once. If you want to access the spools, just lift the metal shaft up. If a small wire spool is installed, there is always more room for insulation tape, scotch tape etc
it works incredibly smoothly and is very strong. the bottom of the stand is corrugated so it grips nicely to a rough desk but there are also round holes for rubber pads.
The middle section has all the main lead exposure health hazards noted down for when you'll inevitably forget about them from all the lead fumes you have been inhaling. The sides have tin and lead elements decals.

_The model is supposed to be printed laying down with the hinge's shaft touching the build plate. The orientation here is very important so that the hinge works properly. I printed mine with .6mm nozzle at .14mm layer height and 10% infill. it's very strong and the letters & decals and perfectly readable. No brim and only one support for the shaft slot on the left side.
After printing, a ~10cm long, 10mm wide shaft is supposed to be pushed into the hole above the hinge. If you dont have a metal shaft, you can always 3d print one though it wont look as neat._

Print in place handle with a hinge .stl

simple handle with a hinge. Print the whole thing then remove the brim and bend the handle a few times to loosen the hinge. It prints already assembled and is suprisingly smooth and sturdy. The rotational range is about 210 degrees. I added only a few supports for the elevated flat parts. Print at low infill with thicker walls depending on the expected load. The hinge is very strong and it hardly flexes when being twisted. for addidtional strength, two machine screws and nuts can be slid into the holes in the hinge. Tolerances in the hinge are pretty high so it should print well on most printers. It can be down-scaled within reason if needed.

I printed mine with black PLA at 50C Bed and 195C nozzle with 100% cooling to better handle the overhangs
the hinge is very squeaky but the noise gets reduced the more the hinge is used, a little bit of thick lubricant can be added to mitigate the issue

Camera battery charge wall mount .stl

Wall mounted battery charger holder, designed to work with a stock canon battery charger but should probably work with other brands. Power cord is routed around the charger through the clips down to the wall plug. Textured back of the print allows for sticking the holder to the wall with double sided tape but it can also be screwed through the holes on the sides.

I printed mine with standard PLA at very low infill and wall thickness to allow for some flex so the charger can be easily removed if needed. If the model is printed with the filament color closely matching the wall color, in blends nicely and is hardly visible.

Spatula & brush holder.stl

All in one holder designed for standard 3d printer spatula and these cheap brass brushes often sold in kits of 3, you can store all of them convinientely push-fit in their spots.
I printed mine with abs at low infill and super glued it to the side of my 3d printer enclosure for easy access, however the holes in the back of the holder allow for also using zip-ties, screws and the corrugated backing sticks well to double sided tape.

Hot glue gun stand.stl

Simple Hot glue gun stand designed to be screwed into a side of a desk (3cm thick desk in my case). The hole at the bottom can be plugged with a metal cup (like a glass jar lid) which will collect dripping hot glue without damaging the plastic shell

I printed mine with abs with some tree supports for the top part. no brim needed

edekpeelek

Achievements

Explorer

Seedling

Debutant