Replacement cap for a Uniball (Uni) Kuro Toga so you can continue to dispense lead.  Cap should snap on, so scaling for your printer by 1% up/down may be necessary.

Kuro Toga Cap.stl

Trypophobians beware!
This is a parametric file which will allow you to make your own custom Gridfinity blocks.  This file is setup to allow you to create blocks with holes in them for holding any number of cylindrical objects such as bottles, pens, markers, pencils, drill bits, etc.  The holes are laid out in 'major' rows with 'minor' rows in between.  There are a number of favorited parameters within the file which allow you to customize as you need:

- slotsWide & slotsDeep - sets the number of 42mm slots your block will occupy
- slotsHigh - sets the height of your block
- majorRowsWide & majorRowsDeep - how many 'major' rows of holes you want in the specific direction
- holeDiameter - how wide each hole should be
- holeDepth - how deep each hole should be
- chamferWidth - the width of the chamfer at the top of each hole
- edgeDistance - how far from the 'rim' the edge of the chamfer should be

Note:  If you do not want/need the center hole(s) you can suppress that feature from the timeline by right clicking on the last hole feature and select "suppress feature".  Then you will be left with a more standard grid of holes instead of a set of alternating holes.
----------------------------------------------------
Derived from: [Gridfinity Divider Bins](https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%2520Divider%2520Bins-60721) by [Zack Freedman](https://thangs.com/designer/ZackFreedman) is licensed under [CC BY-NC-SA 4.0](https://creativecommons.org/licenses/by-nc-sa/4.0/legalcode.txt)

Gridfinity | Hole Customizer

Trypophobians beware, this is a parametric file which will allow you to make your own custom Gridfinity blocks.  This file is setup to allow you to create blocks with holes in them for holding any number of cylindrical objects such as bottles, pens, markers, pencils, drill bits, etc.  The holes are laid out in 'major' rows with 'minor' rows in between.  There are a number of favorited parameters within the file which allow you to customize as you need:
slotsWide & slotsDeep - sets the number of 42mm slots your block will occupy
slotsHigh - sets the height of your block
majorRowsWide & majorRowsDeep - how many 'major' rows of holes you want in the specific direction
holeDiameter - how wide each hole should be
holeDepth - how deep each hole should be
chamferWidth - the width of the chamfer at the top of each hole
edgeDistance - how far from the 'rim' the edge of the chamfer should be

Zack's caliper holder is intended for a Mitutoyo caliper.  For those of us with a Harbor Freight Digital caliper, something else is required, so here it is.

----------------------------------------------------
Derived from: [Gridfinity Divider Bins](https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%2520Divider%2520Bins-60721) by [Zack Freedman](https://thangs.com/designer/ZackFreedman) is licensed under [CC BY-NC-SA 4.0](https://creativecommons.org/licenses/by-nc-sa/4.0/legalcode.txt)

Gridfinity | Caliper Holder - Harbor Freight

Zack's caliper holder is intended for a Mitutoyo caliper.  For those of us with a Harbor Freight Digital caliper, something else is required, so here it is.

Gridfinity Caliper Holder - Harbor Freight

Gridfinity holder for your solder tips which are laying around.  Two versions:
1x1 - 5 Tip
1x2 - 14 Tips
Allows you to see which tips you have available and spaced far enough apart to allow for easy plucking of your desired tip.  Shout out to Zack for his Gridfinity system


----------------------------------------------------
Derived from: [Gridfinity Divider Bins](https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%2520Divider%2520Bins-60721) by [Zack Freedman](https://thangs.com/designer/ZackFreedman) is licensed under [CC BY-NC-SA 4.0](https://creativecommons.org/licenses/by-nc-sa/4.0/legalcode.txt)

Gridfinity | Solder Tip Holder

Solder Tip Holder 1x2x3.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

brian.kerley

Achievements

Explorer

Seedling

Fan Favorite

Kuro Toga Cap.stl

Gridfinity | Hole Customizer

Gridfinity | Caliper Holder - Harbor Freight

Gridfinity | Solder Tip Holder