This is a mashup of hein's desk clamp and Gridfinity. I replaced the top piece of the clamp with Gridfinity baseplates. I made 2 versions.

The first version is a simple 1U high baseplate with holes for magnets. It is intended to mount directly to the desk as normal but have a Gridfinity top that can sit next to other Gridfinity baseplates. It's a bit thin, so use a strong filament that doesn't bend much and do not use for anything too heavy.

The 2nd version clamps and existing Gridfinity baseplate down the the desk, negating the need for screws or weights, and gives 2 more base squares. This one is 2U high to try to make it a little stronger than the other version, but again don't expect it to perform like steel. V2 of the model attempts to make it slightly thicker at the top joint to reduce flex.

I am including the Blender file I used to aid in further modding.


For attachments and other parts for the clamp please see heins original post. I may add some of the other required parts to this listing later for archival/preservation reasons in the future.

======================================

I merged pieces of the following in this model:

Desk Clamp (Modular)
by hein - @hein - https://www.printables.com/@hein
https://www.printables.com/model/508193-desk-clamp-modular
Creative Commons (4.0 International License) - Attribution-NonCommercial

Gridfinity Magnet Light Baseplate
by RIP_Plo-Koon - @RIP_PloKoon - https://www.printables.com/@RIP_PloKoon
https://www.printables.com/model/250550
Creative Commons (4.0 International License) - Attribution

Gridfinity Baseplates
by ZackFreedman  - https://thangs.com/designer/ZackFreedman
https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%20Baseplates-60925
MIT License


I believe the most acceptable license for the combined work would be cc-by-nc and also to include the MIT license for Zack portion below.

======================================

Copyright (C) 2023 - Jonathan Hull
CC-4.0-by-nc

======================================

MIT License text for Gridfinity Baseplates by ZackFreedman:

Copyright (c) 2023 Zachary Freedman and Voidstar Lab LLC



Permission is hereby granted, free of charge, to any person obtaining a copy
of this software and associated documentation files (the "Software"), to deal
in the Software without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
copies of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.

======================================


Desk Clamp with Gridfinity Top

desk_clamp_with_gridfinity_top.blend

desk_clamp_with_gridfinity_top_1U_magnetic.stl

desk_clamp_with_gridfinity_top_2U_clamping_magnetic_V2.stl

This is a remix of Wire Splice Mold by t2pain2 on Thingiverse
https://www.thingiverse.com/thing:6316585


Changes from the original:

 - Split into two models for easier slicer arrangement.
 - Re-scaled to properly fit 14AWG wire without resizing in slicer.
 - Beveled a few edges to allow for easier handling and assembly when splicing.


To use:

1: Insert your pre-spliced wire into one side of the jig. One side is for 1-to-1 the other is for 1-to-2. It should handle most types of slim splices including crimp and heat-gun-solder types, or just raw hand-soldered wire.
2: Mate the two halves of the jig.
3: Clamp the jig together for stability with any small clamp.
4: Inject 2-4 trigger-presses of hot-glue.
5: Wait for it to cool.
6: Remove from jig and trim excess hot glue.

Your wires should have a somewhat more water-tight seal now as long as the splice stayed centered.

That is in theory how it should work. I will test after I perform my first print.


Printing:

As this will be encountering hot glue I suggest using a filament that handles heat the best. PLA is probably good enough for the temp of most glue guns, but if you have other filaments that are more heat tolerant use that to be sure. Best I have is PETG so I will use that on my test print (I haven't printed it yet).


Suggestions for future remixes:

 - Extend the cavity to add a screw-mounting loop.
 - Add something to help center the splice and reduce the chance of shifting of the wires and splice during handling.
 - Possibly make it more symmetrical to allow for a single model that is just printed twice?
 - Add LEDs and other bling (ok, maybe not)



Wire Splice Mold - Slightly Modified

splice half A.stl

splice half B.stl

splice with bevels and resized.blend

As a starting point I used the 3x3 bin from this post:

Gridfinity empty bins for customization + parametric file
https://www.printables.com/model/369952-gridfinity-empty-bins-for-customization-parametric
by Akio (@Akio) on Printables - https://www.printables.com/@Akio
Creative Commons (4.0 International License) Attribution—Noncommercial—Share Alike
https://creativecommons.org/licenses/by-nc-sa/4.0/legalcode.txt

The above bin itself is a remix of Zack Freedman's Divider Bins. MIT licensed.
https://bit.ly/ZFGridfinityDividerBins

Starting file:
divider-box-parametric-empty-3x3x6.step

I loaded the above step file into Meshlab, resaved as STL, then modified in Blender (yeah, I know, no longer the preferred step file but on my OS/system and with my skills that worked best. Get over it, I'm a no pro).
For modification I stretched the height to fit my thermal roll and then added side cutouts to hold the axel. This perfectly fits the 473 count 4x4.5" thermal roll from UPS online supply store, listed as "Direct Thermal 4X4.50 Label". I plan on maxing a bigger version for the 4"x6" 940-count roll later.
I thickened the walls to prevent flexing. I also added a slot to pass the labels through with a pointed ridge to try to allow for easy tearing, but it doesn't quite work the way I had hoped so just use two hands to tear the label sheets. Try to not let the remainder fall within the box.

The modifications were inspired by this model (although I did not use any of it's files/models in my model so it's not technically a remix).
2" Label Dispensor 
https://www.printables.com/model/378067
by DIY Machines (@DIYMachines)
Public Domain

The axle is just a couple cylinders bool'd together with bevels added in blender.

For the lid (model not included) I just shrunk a magnetic stackable baseplate and added some cutouts to make it use less filament. Really, any 3x3 Gridfinity bottom will work as a lid, so use what you prefer or go without a lid. I may post this modified lid/baseplate later, but it is so thin it flexes more than I had anticipated so I'll probably thicken it first if I do post it.

In the photos, it is not intended to be multi-color but I was using up the last of some old ugly seldom used rolls none of which had enough on their own to do a complete print.


Ideas for future improvements/remixes by myself or anyone willing to take a stab at it:

- Reshape and possibly reposition the slot to allow easier tearing and reduce the chance that the remainder will retreat back into the box.

- Create more axles that allow for different hub diameters of various label rolls.

- Thicken walls further, at least under the cutouts, to reduce flexing so as the roll's axle does not fall into the box.

- Create a better lid, or just forget it and let the user figure out a different baseplate or lid to use.

- Reshape the axle to allow for vase-mode printing.


------------------

Remix copyright (C) 2024 Jonathan Hull
Creative Commons (4.0 International License) Attribution—Noncommercial—Share Alike
https://creativecommons.org/licenses/by-nc-sa/4.0/legalcode.txt

Derivative information at top of post.

-------------------

My profile on other sites:

https://thangs.com/designer/Unsecured1103
https://www.printables.com/@MushyUnivers_1096436
https://www.thingiverse.com/cheeryhome


Gridfinity 4" Thermal Label Dispenser

gridfinity 3x3 thermal roll dispenser 4in wide.blend

body thicker walls.stl

axel.stl

This is a model of the Tower of the Americas in downtown San Antonio, TX. This was designed by my son for a school project using Tinkercad, visually copying the tower from photos (so don't expect high accuracy), and then cleaned up/edited a bit by me to prepare for 3D printing. It's a good toy/art piece for kids.

I left the model as once piece, but when printing I split it apart in the slicer and added some color changes. If you do the top as a separate piece you won't need supports. I'll post the photo once printing is done.

Copyright © 2024, Evan Hull and Jonathan Hull
This work is openly licensed via Creative Commons - CC 4.0 BY-NC-SA

Tower of the Americas

Tower of the Americas.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Unsecured1103

Achievements

Seedling

Voyager

Debutant