Key for the Tolerance print. 

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr

Tolerance Key

AmeraLabs Town SLA Calibration print.

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr

AmeraLabs Town Calibration. 

Tolerance Test 

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr



Tolerance Test 

Simple test to test and calibrate supports. 

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr



Support Calibration Test

Flow and Retraction Test

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr

4 Cones Retraction Test

All in One Test print. 

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr

All in One Print

Here are Extruding calibration cubes to measure your flow rate after you calibrated your esteps. 

Print the cube at 0.4 Wall Thickness 
With a 1 Wall Line Count. 

The measurement will then be 0.8


If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr


0.4 Nozzle Extruder Calibration Test Cube

Here are Extruding calibration cubes to measure your flow rate after you calibrated your esteps. 

Print the cube at 0.4 (0.6) Wall Thickness 
With a 1 Wall Line Count. 

The measurement will then be 0.8 (1.2)


If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr


0.4 & 0.6 Extruder Calibration Test Cubes

Here are Extruding calibration cubes to measure your flow rate after you calibrated your esteps. 

Print the cube at 0.6 Wall Thickness 
With a 1 Wall Line Count. 

The measurement will then be 1.2


If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr

0.6 Nozzle Extruder Calibration Test Cube

0.6 Extruder Calibration Test.stl

Here is a temp tower we like to use. Here is how to add the layer changes in Cura. Check out the discord link for Prusa Slicer users. 

Adding post processing to print the tower.
-In Cura be sure to set your Printing Temperature (under Material) to 265 (PETG)
-Then on the top left click Extensions>Post Processing>Modify G-code
-This will allow you change the temps as it gets printed.
-Click on Add a script>ChangeAtZ
-Do that 10 times
-Change Height to [5.0] mm
-Leave Apply to Target Layer + Subsequent Layers. 
-Select Change Extruder 1 Temp. Drop down comes up 
-Extruder 1 Temp 260 -Do this for all of them. 

PETG
5.0 = 260
10.0 = 255
15.0 = 250
20.0 = 245
25.0 = 240
30.0 = 235
35.0 = 230
40.0 = 225
45.0 = 220
50.0 = 215

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr

PETG Temperature Tower 215-265 with Bridge

Adding post processing to print the tower.
-In Cura be sure to set your Printing Temperature (under Material) to 265 (PETG)
-Then on the top left click Extensions>Post Processing>Modify G-code
-This will allow you change the temps as it gets printed.
-Click on Add a script>ChangeAtZ
-Do that 10 times
-Change Height to [5.0] mm
-Leave Apply to Target Layer + Subsequent Layers. 
-Select Change Extruder 1 Temp. Drop down comes up 
-Extruder 1 Temp 260 -Do this for all of them. 

PETG
5.0 = 260
10.0 = 255
15.0 = 250
20.0 = 245
25.0 = 240
30.0 = 235
35.0 = 230
40.0 = 225
45.0 = 220
50.0 = 215

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr



Here is a temp tower we like to use. Here is how to add the layer changes in Cura. Check out the discord link for Prusa Slicer users. 

Adding post processing to print the tower.
- In Cura be sure to set your Printing Temperature (under Material) to 240 (PLA)
- Then on the top left click Extensions>Post Processing>Modify G-code
- This will allow you change the temps as it gets printed.
- Click on Add a script>ChangeAtZ
- Do that 10 times
- Change Height to [5.0]mm 
-  Leave Apply to [Target Layer + Subsequent Layers.] 
- Select Change Extruder 1 Temp. Drop down comes up
- Extruder 1 Temp 235
- Do this for all of them.

  PLA
5.0 = 235
10.0 = 230
15.0 = 225
20.0 = 220
25.0 = 215
30.0 = 210
35.0 = 205
40.0 = 200
45.0 = 195
50.0 = 190

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr

PLA Temperature Tower 190-240 with Bridge

Adding post processing to print the tower.
-In Cura be sure to set your Printing Temperature (under Material) to 240 (PLA)
-Then on the top left click Extensions>Post Processing>Modify G-code
-This will allow you change the temps as it gets printed.
-Click on Add a script>ChangeAtZ
-Do that 10 times
-Change Height to [5.0] mm
- Leave Apply to Target Layer + Subsequent Layers. 
-Select Change Extruder 1 Temp. Drop down comes up
-Extruder 1 Temp 235
-Do this for all of them.
PLA

5.0 = 235
10.0 = 230
15.0 = 225
20.0 = 220
25.0 = 215
30.0 = 210
35.0 = 205
40.0 = 200
45.0 = 195
50.0 = 190

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr

Simple XYZ cube to calibrate your printer. 

If you need any assistance please feel free to reach out to us in our discord.

https://discord.gg/hUWbzNr

XYZ Calibration Cube

xyz_calibration_cube.stl

This model is to test your bed level and make adjustments as needed while its printing. 

Scaled for Ender 3 beds. Scale up as needed for bigger printers. 

If you need any assistance please feel free to reach out to us in our discord. 

https://discord.gg/hUWbzNr 

Bed Leveling Test

This model is to test your bed level and make adjustments as needed while its printing. 

Scaled for ender 3. Scale up as needed for bigger printers. 

If you need any assistance please feel free to reach out to us in our discord. 

https://discord.gg/hUWbzNr 

Bed Leveling Test. 

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Krolbrien

Achievements

Seedling

Fan Favorite