Wall mount pieces for Lego set 75275 UCS A-Wing

2-piece set to mount Lego set to the wall. 
Wall mount is angled slightly to show the A-Wing set slightly tilted out, to give a different view then a head on/flat view. (Around 20 degrees)

2 pieces separated to allow for easier printing, and to allow for designing and printing alternate mount pieces to allow for different angles/positions.
I'm using it to display the A-Wing horizontally but it should also work vertically.

    Print WallMount upright with the open slot to the top.
    (Supports may be required for screw holes depending on printer settings.)
    Mount piece should be printed with the large flat piece on the heat bed and the Arm facing upwards.
     

Secure WallMount part to the wall via suitable fixing. Open slots should face upwards.
Slot Mount piece down into WallMount piece with Arm facing outwards/upwards.
Lego Set can be placed onto the Arm piece, slotting cleanly into the opening under the A-wing for the original display stand.

I printed parts in PETG with at 0.2mm with a 0.6 nozzle and have had no issues at all.
4 or 5 perimeters/shells recommended. 

CAD files included to allow for modification of pieces if alternate angle/positions are required.

Lego Star Wars 75275 UCS A-Wing 

MountPiece25.SLDPRT

Wall mount pieces for Lego set 75382 UCS TIE Interceptor (2024)

2-piece set to mount Lego set to the wall. 
Wall mount is angled in a way to show the Interceptor in slightly tilted down position, mainly as its mounted above head head in its current location. (Around 15 degrees)

2 pieces separated to allow for easier printing, and to allow for designing and printing alternate mount pieces to allow for different angles/positions

    Print WallMount upright with the open slot to the top.
    (Supports may be required for screw holes depending on printer settings.)
    Mount piece can be printed horizontally or vertically, horizontally should give stronger finish but will require post-printing cleaning of supports.
     

Secure WallMount part to the wall via suitable fixing. Open slots should face upwards.
Slot Mount piece down into WallMount piece with upright leg facing upwards.
Lego Set can be placed down, with the upright leg slotting cleanly into the opening under the cockpit for the original display stand.

I printed parts in PETG with at 0.2mm with a 0.6 nozzle and have had no issues at all.
4 or 5 perimeters/shells recommended. 

CAD files included to allow for modification of pieces if alternate angle/positions are required.

Lego Star Wars 75382 UCS TIE Interceptor (2024) 

MountPiece-15.SLDPRT

Made up a wall mount for the 75367 UCS Venator, display the ship at 90 degrees rather then usual 45 degrees. (Due to available mounting space restrictions)

Makes use of some of the technic pieces from the sets included stand, I also suggest some additional bolts or cable ties to add additonal support to be sure. 

Not for the faint hearted, make sure all the pieces are FIRMLY attached before mounting.

The wall pieces are mounted on the wall with the protruding section sticking out to allow the winged section of the stand to slot down into the gap. 
(Reference Model picture shows Rear stand in Blue with the Wing section in Yellow, the Wall Piece is in Red)

With the Front and Rear Stand pieces attached to the Set, and the wall pieces mounted, the set can be slid down into place between the wall and the wall pieces. 

Print four of the Wall Pieces and one each of the Front Stand and the Rear Stand pieces.
Wall pieces have integrated screw holes for mounting.
Stands have slots that fit some of the Technic (holed) pieces (I think 12 studs in length is the best option, I had to use some shorter ones for the front stand and bolted them together)

Printed in PETG, Wall pieces were printed on their side with the narrow edge on the print bed.
Stand pieces were printed with the flat side on the print bed.
Used a 0.6 nozzle and 0.3mm layer height, 25% Infill and 6 shells all around. 
Recommend printing with a brim if you have any adhesion or warping issues. 

The Stand is holding the set firmly but I do suggest some additonal supports to be sure (eg Bolt throught Technic pieces or similiar)
I also suggest using some small lego parts as fixing to hold any loose or rising hull sections together to make a cleaner display. 

LEGO Star Wars 75367 UCS Venator Wall Mount 

RearStand.SLDASM

Description

Wall Mount for Vertical Stand available for Lego 75192 UCS Millennium Falcon.

Designed a wall mount for use with a modified Vertical Lego stand available for the 75192 UCS Falcon. (Search for Efferman Vertical Stand here, or amazon link for the knock off here) 

Stand working well now after finally building the Falcon set and mounting it.
Saves a bit or space as doesn't protrude out as much as an angled display.
Set seems to be mounted very firmly with no issues. 
Have updated post with pictures of the Falcon mounted.

Minor modification required to rear legs of stand, no additional pieces required only change in layout. Removes rear two feet pieces and alterations to support framework. 
All changes shown in pictures. 
This modification was to save some space and display the Falcon at a slightly more upright angle. (Changes by about 20 degrees) 

Print two of the wall mounts and mount securely to wall, 2x screw holes in each mount.
Vertical Stand sits snugly into mount from above.
Stand front foot piece aligns with wall mount cutout, and protruding nub sits in the gap in front of the front upright. 
Rear nub on wall mount sits into the hole in front of the rear upright.

Printed parts in PETG, mounts laying on their side on the print bed.
Supports only required under Front Cut Out and Nubs. 
Used a 0.6 nozzle and 0.3mm layer height, 25% Infill and 6 shells all around. 
Recommend printing with a brim if you have any adhesion or warping issues. 

Used some cable ties to tidy the USB cable running to the Falcon for the light kit so wrapped them around the stand and on to the support to be extra sure, but was mounted for several days without them with no issues.



 Lego 75192 UCS Millennium Falcon Vertical Stand Wall Mount 

WallMount_20_10.STL

Stand for 75356 Executor Super Star Destroyer

2-piece set to display the Lego set.
Lower then original stand and displays set broadside at angle of printed Arm piece.
Designed for use on a high shelf to show more of the top side then the underneath.

Files included for 0°, 5°, 10°,12.5° and 15° angled arm pieces (rough estimate for angle)
Pictures show set displayed with 15° Arm piece. 

2 pieces to be printed, Arm piece slots into tabs on Base part.

    Print Base piece with flat piece on printer bed.
    Print Arm piece with large open square on printer bed and tabs facing upward. 


Use's both 2x4 Lego plates from the original stand to connect to underside of the SSD set. 
These fit snugly into the open square on the Arm piece (May require slight shave if any elephants foot style issues on printer)

Existing triangular side pieces need to be moved out to allow the stand to sit flush to the SSD.  (example pic shown)


I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells recommended. 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

 

UPDATE: 26-May-2023

Added additional Arm pieces at 0°, 5°, 10° and 12.5° degrees (rough estimate)
Original piece is around 15°

 Lego 75356 Executor Super Star Destroyer Low Stand 

Base.STL

Wall Mount to use with various Lego Star Wars TIE models.
Tested with sets 75211(Solo TIE Fighter) and 75348 (Mandalorian TIE Interceptor)
Gives enough clearance to rear for Solar Arrays of both models tested. 

Makes use of a Head piece from MroznyHipis Modular Display Stands to give a slight angle to the models display  (1.Head - 1Brick 8-0 - Interceptor)
Also requires a 2x4 flat Lego plate to connect to bottom of TIE Model.

Print 1x wall mount piece and 1x Head piece per model.

Print wall mount with longest edge face down.
Printed in PETG with 0.6 Nozzle at 0.3mm layer height. 4 Shells.
Support recommended for screw hole.

Head Piece fits into slot on top of wall mount, Superglue to secure.
Also recommend gluing the 2x4 plate to the head piece while you've the glue out.

Secure to wall with via appropriate fixing of your choice via screw hole in rear of wall mount.

Can also be used by ignoring Head piece and gluing Lego plate onto slot on Wall Mount but gives a much flatter flight angle to Model that doesn't look as good in my opinion. 

 Lego TIE Wall Mount 75211/75348 

TIE_WallMount_LegoHead.3mf

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035897.

Wall mount pieces for Lego set 92176 Saturn V Rocket. 

2-piece set to vertically mount Lego Saturn V rocket.

    Print WallBase piece with the wall facing side on the bed (No supports required)
    Print TopClamp piece flat with long arms parallel to printer bed. Supports may be required for the screw hole depending on your printer setup. 

Rocket set sits on WallBase part and TopClamp fits securely near the top of the middle section.
Secure WallBase to surface with appropriate fixings first, then TopClamp piece can be secured once suitable position has been marked.  

I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells minimum recommended. 
 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

 Lego 92176 Saturn V Wall Mount (Vertical) 

WallBase.3MF

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035887.

Wall mount pieces for Lego set 40591 Death Star 2 

1-piece set to wall mount Death Star with parts from its included stand.

    Print WallMount piece with the large hole in the cylindrical piece facing upwards.
    Supports may be required for the screw hole depending on your printer setup. 

Secure WallMount to surface with appropriate fixing.
Remove the existing lower piece of the Death Star mount, leaving the round pieces connected to base of the Lego set.
Slide the round pieces into the hole in the cylindrical part of the mount and affix the Fully Armed and Operational Battle Station atop the round pieces. 

Hole in bottom of cylindrical piece to allow for the grey bar piece that runs through the round pieces.

I printed the part in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells minimum recommended. 
 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

Lego 40591 Death Star 2 Wall Mount 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035892.

Wall mount pieces for Lego set 75355 UCS X-Wing

3-piece set to mount Lego set to the wall. 
Wall mount is angled in a way to show X-wing in flight, with enough clearance to allow all S-Foils to be locked in attack position. 

3 pieces separated to allow for easier printing, and because I messed up the initial clearances and a third part was the quickest way to fix it.

    Print BackPiece on its side with screw holes parallel to print bed.
    (Supports may be required for screw holes depending on printer settings.)
    Print WallMount on its flat side .
    Print WallPiece with largest hole flat on the print bed.
     

Secure WallPiece part to the wall via suitable fixing. Larger hole should face outwards to allow for head of screw/both to be hidden in rounded area.
Slot BackPiece into WallMount piece and align with WallPiece, 2 holes can be used to secure both pieces together with a suitable small nut and both. 

Lego set sits securely atop the WallMount piece, the larger upright fits into the existing mount hole on the bottom fuselage of the set. Two additional smaller uprights fit snugly at the front and rear of the lower fuselage. 

I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells recommended. 

 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

Lego 75355 UCS X-Wing Wall Mount 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035889.

Wall mount pieces for "unreleased" Lego set 42113 Bell-Boeing V-22 Osprey.

3-piece set to mount Lego set to the wall. 
Wall mount is angled in a way to allow clearance for all moving parts (Rotors,Engines, etc.)
 

Hook and Cross piece separated to allow for easier printing.

    Print Hook on its side.
    Print Cross with Prongs facing upwards.
    Printed AngleWallMount with the screw holes on bed.
    Supports may be required depending on printer settings.

Secure AngleWallMount part to the wall via suitable fixings.
Hook and Cross piece slot into AngleWallMount part and can be secured further with a small nut and bolt at the hole where all 3 parts intersect. (Not required but suggested to lock set into wall mount)

Lego set sits onto Hook and Cross piece and slide's forwards to lock in place.
Hook piece goes into slot between battery compartment and lower fuselage.
Cross piece uprights slot into gaps behind rear wheel wells. 

I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells minimum recommended. 

 

This is the first iteration of the wall mount for this set I've designed, so its a bit rough around the edges, I may update it if I can simplify or upgrade it in the future.

Lego 42113 Tilt-Rotor Wall Mount 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6035883.

2 Position upright  stand for Dell Latitude 5580 laptop.

Laptop stand with 2 separate positions for the laptop to slot into.
This is primary for raising the height of the laptop screen to a more ergonomic position.
Most suitable for use with an external mouse and keyboard, however laptop keyboard/touchpad is still fully usable in either position.
 

Print the stand model with flat on the printer bed with the 4 inner slots facing up/down.
Print the model twice for right and left hand side parts.
No supports required.

I printed parts in PETG with at 0.4mm with a 0.6 nozzle and have had no issues at all.
3 or 4 perimeters/shells recommended. 

Dell Latitude 5580 Upright Laptop Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4840830.

### Set of Legs to hold Asus MB169C+ Monitor.

Designed for use with Dell Latitude 5591 Laptop, because the included folding cover/stand is a nice cover, but a terrible stand.
One leg has an opening to allow the USB-C cable connection.
Holds screen at the same height as the main display at an angle of 80 Degrees.
Additional set uploaded to work with Dell XPS 15 (2019) at an angle of 70 Degrees. 

Pictures show parts printed on PrusaMk3 with 0.6 Nozzle using Urban Grey Prusament PETG.

_Original Solidwork part files included if you would like to further edit the parts._  

[Monitor](https://www.asus.com/Displays-Desktops/Monitors/ZenScreen/MB169C-plus/)


ColLynch

Achievements

Trailblazer

Sequoia

Debutant

Pinned models

Lego 92176 Saturn V Wall Mount (Vertical)

Lego 75356 Executor Super Star Destroyer Low Stand

Lego 75192 UCS Millennium Falcon Vertical Stand Wall Mount

LEGO Star Wars 75367 UCS Venator Wall Mount

Lego Star Wars 75275 UCS A-Wing

Lego Star Wars 75382 UCS TIE Interceptor (2024)

LEGO Star Wars 75367 UCS Venator Wall Mount

Lego 75192 UCS Millennium Falcon Vertical Stand Wall Mount

Lego 75356 Executor Super Star Destroyer Low Stand

Lego TIE Wall Mount 75211/75348

Lego 92176 Saturn V Wall Mount (Vertical)

Lego 40591 Death Star 2 Wall Mount

Lego 75355 UCS X-Wing Wall Mount

Lego 42113 Tilt-Rotor Wall Mount

Dell Latitude 5580 Upright Laptop Stand

Asus MB169C+ Stand