This is the Tool used to fit the cap section of my Q Erector style stackable Suppressor with integral baffles (Airsoft ONLY).

The rest of the files can be found here:

https://www.etsy.com/uk/listing/1529251823/erector-q-style-stackable-suppressor?ref=listings_manager_grid

https://cults3d.com/en/3d-model/various/erector-q-style-stackable-suppressor-with-integral-baffles

Erector Q Style Airsoft Suppressor (Tool ONLY)

This is an adaptor to allow the fitting of silencers or barrel extensions to the TM VSR10 Pro (Not Gspec) or JG BAR 10.

I have also designed in an installation tool to make it easier to thread onto the barrel.

I have not tried this file on a VSR as sadly I no longer own one however the dimensions where taken from a left over adaptor I still have.

This was mostly a thought experiment but will hopefully be useful to someone.

Enjoy

I have more files available or at https://cults3d.com/en/users/AirsoftProtoTech/3d-models

3D PRINTING SETTINGS
I would recommend 4 walls for both parts and at least 50% infill for the adaptor itself, the tool will likely only need 15% (so long as you don't use your monkey strength to tighten the adaptor down)

PLA+ or better for material

The adaptor will need supports, the tool will likely print fine with the large face on the print bed.

TM VSR10/JG BAR10 Suppressor Adaptor + Tool

Adaptor.stl

This file is to replace the mounts the come with the Z-Tactical Comtac mounting kit for Arc rails. I found the ones that came with the set where flimsy and kept popping out of the rails, I also snapped off the adjustment ears facepalm

This may or may not work with other headsets but I am currently using this on my own helmet and it works flawlessly.

Uses the original mounting screws.

Check out my other stuff over at https://cults3d.com/en/users/AirsoftProtoTech/3d-models

3D PRINTING SETTINGS
All the walls, all the infill

Printed in PLA+ but go as fancy as you like

0.2mm Layer Height

Tolerances for the locating ring are quite tight so make sure you're printer is calibrated nicely.

Replacement Z-Tactical Comtac Mounts

This file is to replace the mounts the come with the Z-Tactical Comtac mounting kit for Arc rails. I found the ones that came with the set where flimsy and kept popping out of the rails, I also snapped off the adjustment ears facepalm

This may or may not work with other headsets but I am currently using this on my own helmet and it works flawlessly.

Uses the original mounting screws.

3D PRINTING SETTINGS
All the walls, all the infill

Printed in PLA+ but go as fancy as you like

0.2mm Layer Height

Tolerances for the locating ring are quite tight so make sure you're printer is calibrated nicely.

This is a flash hider of my own design combining elements from various popular flash hiders found in popular video games. Would it work IRL??? Probably not!!!

This has a 14mm CCW thread that allows fitting to airsoft replicas ONLY!!! Any attempts to fit this flash hider replica to anything other than airsoft replicas will likely result in injury!!!

Along with the main flash hider there are shim files to allow you to "time" or align to your barrel in the correct orientation, use 1 or several of these in combination to get the best fit. A rubber O-Ring would also suffice.

Please note that none of my flash hider files are 100% accurate in any way and are my interpretation of pre-existing designs.

I have more designs available over at https://cults3d.com/en/users/AirsoftProtoTech/3d-models

3D PRINTING SETTINGS
Material: PLA+ or Stronger however PLA is more than sufficient

Recommended to print vertically with Tree supports on the large openings.

4 Walls with at least 50% infill

I recommend using adaptive layer height if you can otherwise the finest that your printer can handle.

This file has not been tested however if threads seem tight I would recommend the use of a 14mm CCW tap to open them out.

Futuristic Flash Hider (Airsoft)

FlashyBoi8.stl

Barrel Shim .2mm.stl

This is a flash hider/muzzle brake of my own design combining elements from various popular flash hiders found in popular video games.

This has a 14mm CCW thread that allows fitting to airsoft replicas ONLY!!! Any attempts to fit this flash hider/muzzle brake replica to anything other than airsoft replicas will likely result in injury!!!

Along with the main flash hider/muzzle brake there are shim files to allow you to "time" or align to your barrel in the correct orientation, use 1 or several of these in combination to get the best fit. A rubber O-Ring would also suffice.

Please note that none of my files are 100% accurate in any way and are my interpretation of pre-existing designs.

3D PRINTING SETTINGS
Material: PLA+ or Stronger however PLA is more than sufficient

Recommended to print vertically without the need for supports.

4 Walls with at least 50% infill

I recommend using adaptive layer height if you can otherwise the finest that your printer can handle.

Tested on a Bambulabs P1P with no fitment issues however if threads seem tight I would recommend the use of a 14mm CCW tap to open them out.

Custom Flash Hider (Airsoft)

Barrel Shim .1mm.stl

Barrel Shim .3mm.stl

Barrel Shim .4mm.stl

Barrel Shim .5mm.stl

This is a Breacher style muzzle brake found in popular video games.

This has a 14mm CCW thread that allows fitting to airsoft replicas ONLY!!! Any attempts to fit this flash hider/brake replica to anything other than airsoft replicas will likely result in injury!!!

Whilst not required along with the main brake there are shim files to allow you to "time" or align to your barrel in the correct orientation, use 1 or several of these in combination to get the best fit. A rubber O-Ring would also suffice.

Please note that none of my files are 100% accurate in any way and are my interpretation of pre-existing designs.

I have more designs available over at https://cults3d.com/en/users/AirsoftProtoTech/3d-models

3D PRINTING SETTINGS
Material: PLA+ or Stronger however PLA is more than sufficient

Recommended to print vertically, supports shouldn't be needed

Print with Brim

4 Walls with at least 50% infill

I recommend using adaptive layer height if you can otherwise the finest that your printer can handle. The tips of this file are particularly fine so I would slow down the print as you reach the end

Tested on a Bambulabs P1P with no fitment issues however if threads seem tight I would recommend the use of a 14mm CCW tap to open them out.

Breacher Style Muzzle Brake

BREACHER STYLE MUZZLE BRAKE

Hobbyist designer and maker of airsoft parts!!!

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

AirsoftPrototech

Achievements

Seedling

Debutant

Pinned models

Breacher Style Muzzle Brake

Custom Flash Hider (Airsoft)

Erector Q Style Airsoft Suppressor (Tool ONLY)

Erector Q Style Airsoft Suppressor (Tool ONLY)

TM VSR10/JG BAR10 Suppressor Adaptor + Tool

Replacement Z-Tactical Comtac Mounts

Futuristic Flash Hider (Airsoft)

Barrel Shim .2mm.stl

Custom Flash Hider (Airsoft)

Barrel Shim .3mm.stl

Barrel Shim .4mm.stl

Barrel Shim .5mm.stl

Barrel Shim .1mm.stl

Breacher Style Muzzle Brake