M3D - Baby Pumpkipus

M3D-BabyPumpkipus.stl

Valentines Cute Flexi Devil & Cupid

Bellamys3DP - Cupid.stl

Donut Factory Puzzle // 2x2 Twisty Marble Puzzle (24mm & 35mm inner cube)

What's better than a donut? SIX donuts!

---

There's a lot going on in the Donut Factory. Twisting, spinning, snapping... the feel is satisfying, but trying to solve this tricky puzzle might leave you frustrated!

---

**_Assembly_**

This puzzle is built around a tiny [24mm 2x2x2 puzzle cube](https://speedcubeshop.com/products/eastsheen-mini-2x2-keychain-cube?variant=40210339659889). You will have to remove the keychain part.

Print 8 copies of the included STL. No supports are required, but the overhangs may warp a bit on some printers, so you may want to include a wide brim and increase Z-retraction height for travel moves in your slicer settings.

After printing, use flush cutters to remove the brim and flat bottom.

Magnets are optional, but highly recommended since they improve the puzzle action and make assembly easier as well. You will need 48 3mm x 6mm neodymium magnets. I used E6000 adhesive to glue them into place. Each face has 2 magnets. Make sure the left holes all have the same polarity, and the right holes all have the opposite polarity. Also make sure the magnets are flush to the face. It can help to use the corner of a table or some tool to press the magnets into place. Allow the glue to dry before moving forward.

Next, glue 7 of the 8 sections onto the internal 2x2 cube. Use only enough adhesive to connect the print to the corner of a cube. If too much glue smushes out, your puzzle may not rotate!

Once the 7 parts are in place, load up the marbles. This puzzle was designed for use with these 14mm ABS no hole beads (true dimensions closer to 13.6mm). The easier way to add the marbles is to rotate individual halves 22.5 degrees so the tracks form an S-bend, so you can add all the marbles of one color (8 marbles per ring). Watching my assembly video might make this easier to understand!

After loading the 3 rings opposite of the missing piece, fill the top rings, including the final corner, and then glue that into place. 

The magnets will help hold the parts together while drying, but I like using [0.25" x 4" Grifiti Silicone Bands](https://amzn.to/45QcKz6) to compress the parts as well.

Donut Factory Puzzle // 2x2x2 Twisty Marble Puzzle (24mm inner cube)

M3D - Baby Santa Octopus

M3D-BabySantaOctopus.stl

Woodland Dragon

Cinderwing3D Woodland Dragon Curled.stl

Dino Nuggies Multi-Pack

Caps - Dino Nuggies.3mf

Owl V1 Fidget

BOB_Owl_V1_Painted.3mf

Yoshi Clicker / Figure

YoshiFigure.stl

Lobsters 

BOB_Lobster_NoLegs_Painted.3mf

Layer Shift Fidget Toy for Halloween

Layer Shift Presupported.3mf

Wickedwing Dragon

Cinderwing3D_Wickedwing.stl

Toxic Waste Fidget Clicker

Toxic Waste.stl

Highland Cow Turtle

HighlandCow-Turtle-RADesigns.stl

Twisted Fox Flexi

TwistedFoxFlexi.3mf

LoveBunz - Nomz

LoveBunz - Nomz.3mf

My Dream Monster -Disguise

MyDreamMonsterDisguise4Color3MF_FunFam3D.3mf

Edgy Mini Dragon (Magnet/Keychain)

MiniDragon_Edgy_1Color.3mf

Mewtwo Clicker

ballV3.stl

Ginger the cat 

Gingerbread cat flexi.stl

Shakaworld3d Pumpkin Patch Dragon Challenge Release V1.stl

Another printing Challenge - the Pumpkin Patch Dragon is a print in place dragon.  The challenge is to print it without supports and a brim.

fidget

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

M3D - Baby Pumpkipus

Valentines Cute Flexi Devil & Cupid

Donut Factory Puzzle // 2x2 Twisty Marble Puzzle (24mm & 35mm inner cube)

M3D - Baby Santa Octopus

Woodland Dragon

Dino Nuggies Multi-Pack

Owl V1 Fidget

Yoshi Clicker / Figure

Lobsters

Layer Shift Fidget Toy for Halloween

Wickedwing Dragon

Toxic Waste Fidget Clicker

Highland Cow Turtle

Twisted Fox Flexi

LoveBunz - Nomz

My Dream Monster -Disguise

Edgy Mini Dragon (Magnet/Keychain)

Mewtwo Clicker

Ginger the cat

Shakaworld3d Pumpkin Patch Dragon Challenge Release V1.stl