Jack Christmas Bauble- Nomz

Jack christmas bauble- Nomz.3mf

Diamond Christmas Ball Design 2

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems. It may be a little challenging to print. The key is to get the speed, temperature and flow right for your particular printer/filament combo so the stem prints cleanly at the narrowest point.

I printed this in Matterhackers Translucent Red. It's a nice balance between translucency and reflectivity. For an opaque filament, I'd use a multi-color PLA (like Matterhackers Quantum) or a medium toned silky PLA (gold, red, just use anything that's not really light or dark). Either type of filament would show off the facets nicely.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 110, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm and adding custom settings for the base of the ball that printed it 0.8 mm thick. You can do this by adding a support blocker to the bottom and giving it custom settings of 0.4 mm. Cura adds the two and prints the area within the blocker at 0.8 mm.

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I really relied on the supports for build plate adhesion. I used a brim, but I set it to 3.2 mm gap from the print so it would touch the supports but not the ornament.

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
Support Overhang Angle: 45 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 m above the build plate so that the supports would only be added to the bottom of the ornament.

Cauldron Bucket - Halloween

Cauldron-Cauldron_Holoprops.stl

Candy Corn Bowl

small Candy corn monster full.stl

XL Easter Bunny - upgrade parts

XL Easter bunny sleeves extra parts 1.3mf

(Italian) Apulian Pumo (1)

Sharing something about my homeland ☺️

The **pumo** is a** traditional decorative element** from my region, Apulia, which symbolizes **spring** 🌼

Its shape resembles that of a **bud**, ready to **bloom**, with the auspicious meaning of **fertility, wealth and good omen** for future events.

To bring luck, wealth and prosperity, however, the pumo must be given as a gift. In fact, it's often chosen as party favors on several occasions.

In this case, I hope you like and would accept them as my gift for you!

Hope you'll enjoy printing these models and add them to your decorations and also, why not, gift them to your friends, relatives and everyone else you would like to ☺️

**Get the other exclusive models of Pumo available only on my** [Patreon Page](https://www.patreon.com/RandomizY) !
⸻⸻⸻⸻⸻⸻⸻⸻
𝗠𝗬 𝟯𝗗 𝗣𝗥𝗜𝗡𝗧𝗜𝗡𝗚 𝗦𝗘𝗧𝗧𝗜𝗡𝗚𝗦 :

🔸 3D Printers: Geeetech A10
🔸 Nozzle: 0.4 mm
🔸 Slicer: Ultimaker Cura 4.13.1
🔸 Layer height: 0.2 mm (0.4 mm wall thickness; 5 top / 2 bottom layers)
🔸 Infill : 0%
🔸 Supports are not strictly mandatory, but you can use them if you prefer (to be sure to better print bottom part of the leaves)
🔸 Printing Temperature: 205°C / Build Plate Temperature: 60°C
🔸 Print speed: 50 mm/sec | Outer Wall Speed: 25 mm/sec
🔸 Filaments: Silk Blue PLA by Eryone
🔸 Size: 9,5 x 9,4 x 10 cm (X,Y,Z)
⸻⸻⸻⸻⸻⸻⸻⸻
Don't be shy and upload your make! (If you share it on your socials, please be sure to tag @𝙧𝙖𝙣𝙙𝙤𝙢𝙞𝙯𝙮.3𝙙, so that I can see and re-share it / if you have TikTok, you can also use the hashtag #𝙧𝙖𝙣𝙙𝙤𝙢𝙞𝙯𝙮 when sharing your video)
⸻⸻⸻⸻⸻⸻⸻⸻
𝙏𝙝𝙞𝙨 𝙬𝙤𝙧𝙠 𝙞𝙨 𝙡𝙞𝙘𝙚𝙣𝙨𝙚𝙙 𝙪𝙣𝙙𝙚𝙧 𝙩𝙝𝙚 𝘾𝙧𝙚𝙖𝙩𝙞𝙫𝙚 𝘾𝙤𝙢𝙢𝙤𝙣𝙨 𝘼𝙩𝙩𝙧𝙞𝙗𝙪𝙩𝙞𝙤𝙣-𝙉𝙤𝙣𝘾𝙤𝙢𝙢𝙚𝙧𝙘𝙞𝙖𝙡-𝙉𝙤𝘿𝙚𝙧𝙞𝙫𝙖𝙩𝙞𝙫𝙚𝙨 4.0 𝙄𝙣𝙩𝙚𝙧𝙣𝙖𝙩𝙞𝙤𝙣𝙖𝙡 𝙇𝙞𝙘𝙚𝙣𝙨𝙚.
⸻⸻⸻⸻⸻⸻⸻⸻
**_If you would like to support me, receive exclusive benefits and you're interested in having a commercial license for selling 3D Printed items (not files) of my works, please visit my Patreon here:_** https://www.patreon.com/RandomizY
⸻⸻⸻⸻⸻⸻⸻⸻
𝗣𝗔𝗧𝗥𝗘𝗢𝗡 : https://www.patreon.com/RandomizY

𝗜𝗡𝗦𝗧𝗔𝗚𝗥𝗔𝗠 : https://www.instagram.com/randomizy.3d/

𝗖𝗵𝗲𝗰𝗸 𝗠𝗼𝗿𝗲 𝗛𝗲𝗿𝗲 : https://linktr.ee/RandomizY

Apulian Pumo (1)

Tissue Box Cover Collection

arabesque tissue box.stl

Gingerbread star cookie Ornament

Gingerbread star cookie.3mf

Skull cave booknook

Skull cave booknook.stl

Cathedral Christmas Stretch Ornament 2024

Stretch Cathedral.stl

Closed Lattice Christmas Bell

This is the third in this year's Christmas bell series. It prints quickly ad easily. Use a nice medium toned silky, metallic or multicolored filament to show off the geometry - or use translucent filament to make it glow.

This is based on my spiral and open lattice bells. It's roughly the same size (slightly taller) with a new loop at the top and a new lattice pattern. 

###Not to be Sold
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

*** PRINT SETTINGS***
* Walls: 0.4 - 0.8 mm (I used 0.4 mm for the clear bell and added an alternating extra line for the opaque bell)
* Layer Thickness: 0.15 mm recommended. Anything from 0.1 - 0.2 mm should look good.
* Infill: None. Seriously. It doesn't need it. It just adds weight and print time.
* Rafts/Brim: I didn't use either. However, the first layer is just a single width circle, so you may need to add a brim or raft.
* Supports: None. I designed this to print cleanly without them.

decoration,

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Jack Christmas Bauble- Nomz

Diamond Christmas Ball Design 2

Cauldron Bucket - Halloween

Candy Corn Bowl

XL Easter Bunny - upgrade parts

(Italian) Apulian Pumo (1)

Tissue Box Cover Collection

Gingerbread star cookie Ornament

Skull cave booknook

Cathedral Christmas Stretch Ornament 2024

Closed Lattice Christmas Bell

Halloween Skull Keychain 2

Christmas Bearded Dragon - Mini Monster #5

LAMP KIT LAMP WITH COLOR CHANGE

Santa Stitch Wallart

Wall mounted Ghost Trap -- Ray Stifz

holly wreath wall art Merry Christmas decor

Mini Cauldron Tealight Holder 2 / 3mf included

Vase NINA - Elegant Flower Vase

Cute Christmas Gnome / New Year Gnome