Is your computer freezing up? Maybe you shouldn’t have downloaded this file!

See here for video: https://youtu.be/3vzdYdMVY9w 

The slot on the back of the holder is 20mm, which will fit most flat screen monitors. You can also use on drawers, boxes or doors.

Print the “Icicle” files in “vase” or “spiralize” mode. Set “Bottom Layers” to zero to keep the bottom open. Holders are for four or six icicles. 


Frozen Computer Icicles

Display only do not print.stl

These vintage-style ornaments are designed for spiralized printing to maximize translucency and minimize material and print time. Download includes six different mix-and-match styles!

See here for video: https://youtu.be/JIcOVe_VUuc 

 More Spiralized Ornaments:
Vintage: https://than.gs/m/964487 
Textured: 

When printed with a 0.4mm nozzle, each ornament requires less than 8g of material. You could print over 125 ornaments with 1kg of filament! A great way to get the most out of your specialty (expensive!) filaments.

For each ornament, you will need to print out a “top” and “Bottom” file. Be sure to use “spiralized” or “vase” mode! You will need to open up the hole in the top by trimming the inside protrusion with a pair of clippers. See video for demo.

Here are some recommendations for spiralized printing:
- Use thick layer heights, 0.2mm or greater
- Set your “Bottom Layer” to 1
- Try using a skirt for bed adhesion, but if that is not working then try a brim. You will just have to remove the brim afterwards
- If you get funny stringing on the top layer, try moving the z-seam alignment around


Spiralized Ornaments - Textured

Hex Top.stl

This tree-shaped Advent Calendar is designed for spiralized printing to maximize translucency and minimize material and print time.  

See here for video: https://youtu.be/465gKQOovwg 

The “ornaments” are sized to hold standard-sized foil-wrapped chocolate balls (22mm or 7/8 inch diameter). Balls will hold in place on their own or can be enclosed with the “Snapball” pieces. The top of the tree holds a “Large Snapball” that can be filled with Smarties or M&Ms. Use translucent filament to make the treats visible! 

You will need to print one each of the “Trunk” and “Tree Layer” files, two each of the “Tree Topper Snapball” files, and 24 of the “Ornament Snapball” files. 

Here are some recommendations for spiralized printing:
- Use thick layer heights, 0.2mm or greater
- For “Tree Layer” files, set your “Bottom Layer” to “0” so that they print with an open bottom.
- The “Truck” can be printed with or without bottom layers, depending on whether or not you intend to put lighting underneath
- The “Snapball” files can be printed with “0” or “1” bottom layers. 
- Try using a skirt for bed adhesion, but if that is not working then try a brim. You will just have to remove the brim afterwards
- If you get funny stringing on the top layer, try moving the z-seam alignment around or adjusting the layer height slightly

More similar Snapball designs:

Ice Bubbles: https://than.gs/m/960766 

Ornaments:
Vintage: https://than.gs/m/964487 
Textured: https://than.gs/m/970064

Giant Spiralized Sphere: https://than.gs/m/965238


Snapball Advent Calendar

Tree Layer 4.stl

This four-piece snap-together Frosty uses only 16g of filament to print! And there is room inside to hide your candy.

See here for video: https://youtu.be/7eFPDJ6JYg0 

These pieces are designed for printing in “spiralized” or “vase” mode.

For each Frosty Snapman you will need to print a “Base,” “Base to Mid”, “Mid to Top” and “Top” file. There are plain and decorated versions of each. Select “Flat Base” if you want Frosty Snapman to be able to stand! 

The pieces snap together in specific orientations, so if Frosty looks crooked just try reorienting the pieces.

Be sure to use “spiralized” or “vase” mode. The above 16g filament estimate is for spiralized mode with a 0.4mm nozzle.

Here are some recommendations for spiralized printing:
- Set your “Bottom Layer” to 1
- Try using a skirt for bed adhesion, but if that is not working then try a brim. You will just have to remove the brim afterwards
- If you get funny stringing in places, try moving the z-seam alignment around of changing the layer height slighty.


christmas Ornaments

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Frozen Computer Icicles

Spiralized Ornaments - Textured

Snapball Advent Calendar

Frosty Snapman - Flat Base.stl