The Rocktopus

My daughter sent me a TikTok of someone's print. It was "The Rocktopus", it was on Cults3D, but it was a pay-version, which I thought was weird. Why did I think it was weird? Because I've seen the Cute Ocotpus and recently I saw the Jumanji statue of Dwayne Johnson on here. Instead of supporting what could be a dubious creator, I decided to hack together my own version from the two.
I apologize for the poor job, but I am a newbie when it comes to 3D modeling ;P I hope you find it as amusing as I did :)

No supports needed.

Use a raft if you are worried about the small contact points on the tentacles. I printed it a couple of times without with success :)

This was remixed with the Dr. Smolder Dwayne Johnson statue and the cute octopus on thingiverse. Both CC BY-NC-SA-licensed models.

**No, you can't sell these. This model and the models it was remixed from are all licensed CC BY-NC-SA 4.0**

Mr. Rockboto: the Benchmark Bot

Mr. Rockboto is not only a fun print-in-place figure but it is also a very useful calibration tool.

He has 14 functional joints with different orientations, couplings, and tolerances. The tolerances range from 0.2 - 0.5mm and allow you to test the minimum clearances your printer can produce and still achieve print-in-place movement.

Each limb is labeled with the tolerances of their joints and all other joints have a 0.3mm tolerance. It might take a little (just a little) bit of force to break them free any more and you risk breaking the robot.

Link to the original Benchmark Bot:
https://thangs.com/Kazi%20Toad/Benchmark%20Bot-55105

Print Settings:

No support!
No brim!

The point of the Benchmark Bot is to find the best parameters to make it function, therefore it is difficult to recommend any settings.

That being said, I used the following parameters:
0.4mm nozzle, 0.2mm layer height, PLA, 3 walls, 4 top/bottom layers, 10% infill.

cRock (The Rock + crocs)

Just a fun mashup I slung together.  This model is not wearble, even if scaled up.  Supports are needed for this model. Remixed from these two files: 
1) https://www.prusaprinters.org/prints/32751-dr-smolder-bravestone-dwayne-johnson
2) https://www.thingiverse.com/thing:3142743/files

**Printing, Assembly & Post Processing**
									
**FDM or Resin:** FDM or resin			
**Scaling:** Current Size: 79 x 177 x 78. Scale up or down as you please!
**Supports:** Supports needed ion the inside of the shoe, and the underside. 
**Nozzle Size I Used:** 0.4			
**Infill/Perimeters:** 15% with 2 perimeters 
**Layer Height:** I used 0.20, but any layer height should be fine.	

**This design is uploaded with a non-commercial license. Purchasing this file does not grant you the rights to sell commercially.

If you would like to consider gaining access to ALL of the models and the rights to print and sell, you can check out my Patreon at https://www.patreon.com/thinair3D				

Rock rock (The Rock + a rock)

Just a fun mashup I slung together.  I 3D scanned a rock and remixed the model with this file: 
1) https://www.prusaprinters.org/prints/32751-dr-smolder-bravestone-dwayne-johnson

**Printing, Assembly & Post Processing**
									
**FDM or Resin:** FDM or resin			
**Scaling:** Current Size: 96 x 88 x 96. Scale up or down as you please!
**Supports:** No supports needed.
**Nozzle Size I Used:** 0.4			
**Infill/Perimeters:** 15% with 2 perimeters 
**Layer Height:** I used 0.20, but any layer height should be fine.	

**This design is uploaded with a non-commercial license. Purchasing this file does not grant you the rights to sell commercially.

If you would like to consider gaining access to ALL of the models and the rights to print and sell, you can check out my Patreon at https://www.patreon.com/thinair3D				


Dwayne the Block (Lego Rock) key cap

Rockachu.stl

Pickachu? The Rock?

Why not Both?!

:D

ENjoy!

The Rock Labubu

model (22).stl

dwayne the valve johnson

dwayne_the_valve_johnson.stl

Rockephant

Dwayne Zen Jhonson - Buddrock

The Rock Buddha.stl

FREE Tyrani-Rock-Tar, Tyranitar The Rock / Pokemon 0

TyraniRockTar_Horns_.stl

GROCKGU 1 hairify contest

#HairifyAnythingContest
It's a remix of GROCKGU -  The Rock meets Grogu by DirtyFacedKid

The rock

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

The Rocktopus

Mr. Rockboto: the Benchmark Bot

cRock (The Rock + crocs)

Rock rock (The Rock + a rock)

Dwayne the Block (Lego Rock) key cap

Rockachu.stl

The Rock Labubu

dwayne the valve johnson

Rockephant

Dwayne Zen Jhonson - Buddrock

FREE Tyrani-Rock-Tar, Tyranitar The Rock / Pokemon 0

GROCKGU 1 hairify contest

WWE - FREE wall art