Get commercial license and download newest models cheaply- https://www.patreon.com/c/goodesign

This is a Display Stand for the F-5E that I designed.

Of course, airplanes can be fully displayed and appreciated only with this display stand.

Like the previously designed Display Stand, there is a drawer to store the landing gear.

And you can also change the angle left and right.

Of course, you can connect this Display Stand even while armed.

Please check the video for details.
https://youtu.be/tMpIqwjbyXk?si=bto-8yNw-ZD9R322

I hope you can display and enjoy the F-5E I designed with this Display Stand.

This design does not include the F-5E fighter. For the F-5E fighter, please see the link below!
Download F-5E - https://than.gs/m/1492963

F-5E Display Stand

GOODesign_F-5E_STAND.stl

Get commercial license and download newest models cheaply- https://www.patreon.com/goodesign

The F-5E, which I designed this time, was developed as a low-maintenance aircraft and was operated in many countries for a long time. That's why it's a fairly popular airplane. In particular, it appeared as the aircraft used by the main character in the Japanese animation Area 88, proving its popularity.

It's very easy to make, but there are a few caveats.
1. Be sure to remove the support first.
2. To balance the aircraft, AAA batteries to act as weights can be placed under the cockpit. However, for those who are concerned about battery fluid leaking out after a long period of time, we have attached an STL in the shape of an AAA battery, so you can print this and insert it. but. When you want to print and use it, you must print it with 100% infill to act as a weight.
3. The nose radome must be attached to the fuselage with the arrow pointing upward.
4. When assembling the fuselage and wings, pay attention to the shapes of the projections and grooves, align them, and push the wings all the way to the front of the fuselage, then insert the rear part of the fuselage.
5. The flap and aileron hinge at the rear of the main wing must be installed with the center protrusion facing outward. Please check carefully.
6. When installing a horizontal tail wing, you must first insert the hinge part into the wing and then insert the wing into the fuselage.
7. When installing the tire parts of the front landing gear, you must spread the tire parts with force before inserting them. The landing gear is thin and easily broken, so be careful when applying force.

Please check and refer to the video for detailed process.
https://youtu.be/3oaY3Xa5XRc?si=ivuq5sdR4jst86SF

As with other military airplanes, we plan to design an armament set and stand. We hope to receive a lot of response from you all.
Download Display stand - https://than.gs/m/1492964

F-5E Tiger II

GOODesign_F-5E_Tiger-ii_Fuselage.stl

Get commercial license and download newest models cheaply- https://www.patreon.com/goodesign
The popularity of the foldable tiger tank late production was great. And there were many requests to produce early production as well. In response to these customer demands, this time, Foldable Tiger tank early production was designed.

Early production differs from Late production as follows.
1. First of all, the turret is a bit simpler, and there are no extra tracks. Instead, there are smoke-making devices.
2. An air filter is installed on the back of the body.
3. Lighting is installed in front of the body.
4. The wheels have a simpler shape.
5. Other details have different shapes.

The process of folding this tank is the same as the late production we made earlier, and is as follows.

Fold the front part first. Since the living hinge is used, fold it carefully and slowly so as not to break it.
Insert the side part with wheels on the front part and the top part. Check and fit each protrusion and hole.
Insert the rest of the side part. The body has been completed.
Connect the two tracks / caterpillars first.
Wind the track / caterpillar around the wheel. There is a change in shape, and the non-simple side is the outside of the track / caterpillar.
Fit the start and end parts of the track / caterpillar.
Put the cannon on the turret.
Glue the small parts on the back.
※ If the track is loose, try the following method.
1. If you increase the material flow in all slicers, more material will be discharged and the volume of the part will increase. This effect reduces the gap between the parts so that the tracks do not come loose or fall out.
2. And in case of using additional Cura, use Outer wall inset or Skin overlap percentage option.

https://youtu.be/kddCizsnZGw
https://youtu.be/LYcwto1NEAM
https://youtu.be/X8jNZoXv8bM

Print out this Foldable Tiger tank early production to complete your Tiger tank collection!

1 : 48 scale
When expanded, size = X 134mm, Y 178mm, Z 112mm After folding X 82mm, Y 185mm, Z 62mm

Foldable Tank TIGER-I early production

GOODesign_Foldable_Tank_Tiger-I_Early-Production_Hull.stl

This time, I finally challenged the tank. Yes, it is a foldable tank. The first selected model was the German Tiger-1 late model, well known in World War II.

Since almost every detail has been expressed, just looking at it will give you great pleasure.
As with other designs, this design has a lot of moving parts, especially wheels, so it is necessary to adjust the height of the nozzle well so that the gaps do not stick when printing the first layer.
In particular, the most important thing to note when printing this design is to print the Track / caterpillar. Pay attention to the print of the first layer so that the Track / caterpillars do not stick together.

The process of folding this design is as follows.
1. Fold the front part first. Since the living hinge is used, fold it carefully and slowly so as not to break it.
2. Insert the side part with wheels on the front part and the top part. Check and fit each protrusion and hole.
3. Insert the rest of the side part. The body has been completed.
4. Connect the two tracks / caterpillars first.
5. Wind the track / caterpillar around the wheel. There is a change in shape, and the non-simple side is the outside of the track / caterpillar.
6. Fit the start and end parts of the track / caterpillar.
7. Put the cannon on the turret.
8. Glue the small parts on the back.

※ If the track is loose, try the following method.
1. If you increase the material flow in all slicers, more material will be discharged and the volume of the part will increase. This effect reduces the gap between the parts so that the tracks do not come loose or fall out.
2. And in case of using additional Cura, use Outer wall inset or Skin overlap percentage option.

1 : 48 scale
When expanded, size = X 134mm, Y 178mm, Z 112mm After folding X 82mm, Y 185mm, Z 62mm

Design by GOODesign

TIger

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

F-5E Display Stand

F-5E Tiger II

Foldable Tank TIGER-I early production

Foldable Tank TIGER-I Late production