This release includes the ship with full cockpit interior and all weapon accessories in 1/48 and 1/72 scale. 

The length in 1/48 scale is 373.5 mm (14.705 in)
The length in 1/72 scale is 249 mm (9.803 in)

All parts are optimized for resin printing.
Pre-supported STL files and Lychee Slicer Scenes for resin printing are included for both scales.


**Notes for assembly 1/48 scale**
The ship has a recess for a M6 nut on the bottom.
M6 Nuts: https://amzn.to/42J9tkB

The Gatling Guns and the Gatling Gun Hatches have recesses for Magnets to swap them out.
Magnets 5x1mm: https://amzn.to/418CW6S

The Bottom Gun and Bottom Gun Hatch have recesses for Magnets to swap them out.
Magnets 3x1mm: https://amzn.to/42QLAb5
The Bottom Gun comes in two versions. One solid and one hollow for LED lighting (1.5mm LED, holes for cable routing must be drilled)

The Canopy can be printed with or without glass.


**Notes for assembly 1/72 scale**
The ship has a recess for a M3 nut on the bottom.
M3 Nuts: https://amzn.to/4jSBEES

The Gatling Guns and the Gatling Gun Hatches have recesses for Magnets to swap them out.
Magnets 5x1mm: https://amzn.to/418CW6S

The Bottom Gun is too small for magnets. Therefore, you need to use double-sided tape (or similar) in order to swap the parts.
The bottom gun comes in two versions. One solid and one hollow for LED lighting (1mm LED, holes for cable routing must be drilled).

The Canopy can be printed with or without glass.


If you still need a good slicer for resin printing, I recommend Lychee Slicer:
https://lychee.co/pricing-and-subscription?utm_source=affiliae&utm_campaign=lychee&utm_medium=NerdMaker&ae=55 *


**Info**
Min. required printer build volume: 192x120x200 mm (WxDxH)
Print the wings and the fuselage with engineering resin (or similar that has little to no flex) to prevent any sagging. Don’t use an ABS-like resin.
Cure the wings and the fuselage very thoroughly immediately after printing for at least 20-30 minutes (washed of course).

My resin recommendation: https://amzn.to/454ywQd

For assembly guidance I recommend to import all STL files in Fusion. Then you can see the entire model in 3D, hide/show every part and see exactly where every part goes. An instruction how to do that and a color guide are included in the download.


**Join the NerdMaker Community**
[YouTube](https://www.youtube.com/@DominicSchwarz?sub_confirmation=1)
[Twitch](https://www.twitch.tv/nerdmaker86) 
[Discord ](https://discord.gg/9jppu3AxJK)
[Instagram ](https://www.instagram.com/nerd_maker_engineer)
[Facebook ](https://www.facebook.com/nerdmakerengineer)


**License**
A Commercial License, to sell 3D-Prints of my Models, is available here:
[Patreon ](https://www.patreon.com/NerdMaker)



All amzn.to links are Amazon Affiliate links. As an Amazon Associate I earn from qualifying purchases. The price will stay the same for you of course!
*This is an affiliate link. If you purchase the Plus or Library license via this link, I get a small commission from Lychee. The price will stay the same for you of course!

Model-T Avenger - 1-48 and 1-72 scale

TIE Avenger 1-48 - Hull front.stl

This is a 3D printable Diorama of an X-Wing Cockpit in 1/6 scale for the Hot Toys / Sideshow figures. Since not everyone has the space to display a full 1/6 scale X-Wing in their homes, I decided to create this cutout diorama. It will fit nicely on your shelf :)

The flight stick, the targeting computer and the canopy are articulated. And not only is the canopy articulated, it also has a fully working mechanism (that can also be motorized, if wanted).
You can choose to either use a Hot Toys, Sideshow or Sphero R2-D2 or use the included STL files to 3D print R2 or R5 (It is a half R-Unit as in the X-Wing studio model).
R2’s head can also be turned.
The cockpit can be lit with 2 mm fiber optics.
R2 can be lit with 0.5 and 7 mm fiber optics.

**Data**
Length: 687 mm
Width: 353 mm (without ladders)
Height: 434 mm (with R2)


**Info**
Min printer build volume: 250 x 250 x 250 mm (WxDxH)
3MF Bambu Studio file included

**Join the NerdMaker Community**
[YouTube](https://www.youtube.com/@DominicSchwarz?sub_confirmation=1)
[Twitch](https://www.twitch.tv/nerdmaker86) 
[Discord ](https://discord.gg/9jppu3AxJK)
[Instagram ](https://www.instagram.com/nerd_maker_engineer)
[Facebook ](https://www.facebook.com/nerdmakerengineer)


**License**
A Commercial License, to sell 3D-Prints of my Models, is available here:
[Patreon ](https://www.patreon.com/NerdMaker)


Model-X Cockpit Diorama 1/6

R2 Dome.stl

This is a 3D printable model kit of the famous Incom T-65 X-Wing, used by the Rebellion in several Battels to fight the Empire.
The scale of the model is 1/12 to fit the pilot from the Hasbro 6 Inch Black Series (not included). 
STL-files for the astromech droid are included. If you choose to use a R2 unit from Hasbro, it needs to be cut to fit into the slot.
The 3D model is highly detailed to replicate the studio model used for filming in the original STAR WARS Trilogy.
It is designed like a giant model kit. You print it piece by piece and then assemble it.
The STL-files have a high resolution to achieve great print results.

These three pilots are available from Hasbro (you can repaint the helmet to be any other pilot, though):
Luke Skywalker: https://amzn.to/3EYBPPy *
Wedge Antilles: https://amzn.to/3X8spr2 *
Antoc Merrick: https://amzn.to/3QtBS8A *


**Features**
- Articulated S-foils.
- Articulated targeting computer. 
- Astromech droid with turnable head (R2, R4 and R5); R2 can be lit.
- Alternative parts for the different studio scale models are included.
- The canopy can be displayed closed and open.
- The finished model can be mounted on a threaded stand or it can be displayed landed with the included landing gear.
- The kit includes two ladders, if you want to display the X-Wing in a hangar scene. (One for the pilot and one for the hangar staff.)
- Cable routing for lighting is possible.

 
**Data**
Length: 1060mm 
Width: 870mm
Hight (with S-foils locked in attack position): 335mm
The fully assembled model weighs around 5kg (depending on your infill ratio).
166 STL-files for 3D printing
1 STL-file complete X-Wing, for viewing purposes only


**Info**
Recommended printer build volume for the native scale: 300x300x265 mm (WxDxH)
The model kit was designed that all details are visible when printed with a 0.4mm nozzle. If you scale the model down you should consider a thinner nozzle.
The parts are not oriented in the ideal printing orientation by default. Orient them in a way that fits best for your printer. Choose suited support structures, if needed.
The download includes a PDF with further information and instructions.


**Join the NerdMaker Community**
[YouTube](https://www.youtube.com/@DominicSchwarz?sub_confirmation=1)
[Discord ](https://discord.gg/9jppu3AxJK)
[Instagram ](https://www.instagram.com/nerd_maker_engineer)
[Facebook ](https://www.facebook.com/nerdmakerengineer)

**License**
A Commercial License, to sell 3D-Prints of my Models, is available here:
[Patreon](https://www.patreon.com/NerdMaker)



For some video impressions visit:
https://youtu.be/SUxNJJH4eOM
https://youtu.be/L6XjmnLeqzE


May the force be with you!


(*) Alle amzn.to Links sind Amazon Affiliate Links. Werden Käufe über diese Links getätigt, erhalte ich eine kleine Provision von Amazon. Der Preis für dich ändert sich dadurch natürlich nicht.
All amzn.to links are Amazon Affiliate links. If purchases are made via these links, I receive a small commission from Amazon. Of course, this does not change the price for you. 

Model-X MK I (1/12 Scale)

DROID_STRIP.stl

Get commercial license and download newest models cheaply- https://www.patreon.com/goodesign

To complete the Futurama series, I finally designed the Planet Express spaceship. I put my best effort into making the design as suitable as possible for 3D printing. I tried to faithfully recreate the appearance seen in the cartoon, and I also gave a lot of thought to replicating as many moving parts as possible. For example, the boarding stairs at the front can fold and unfold, the hangar can open and close, and of course, the turret on top rotates.

In addition, to enhance the sense of realism, I added my own imagination by engraving panel lines similar to those I’ve used in the other spaceships I’ve designed.

The printing and assembly process is very simple, but there are a few things you need to pay attention to:

When attaching the turret to the main body, you should apply glue only around the edges so that the turret can rotate later. This detail isn’t clearly shown in the video, so please keep it in mind.
When attaching the folding stairs at the front, make sure to align the pegs and holes properly before inserting them.
When attaching the outer wall of the hangar (the light green part), make sure to check the direction of the parting line. You can see this in the video.
The rings and wings of the horizontal stabilizers on both sides won’t fit if they’re misaligned, so please test-fit them first before gluing. Once you’ve confirmed the alignment, then attach them permanently.
The logo on the vertical tail has circle and triangle markings engraved on the base, so just align those markings when attaching it.
The landing gear covers are marked with the letters R and L for right and left, and you just need to insert them with the letters facing inward.

For more details, please refer to the video. https://youtu.be/Jqm8zHlQoqY

Complete your Futurama series with this Planet Express spaceship!

Head quarter download link - 

Filament color :
Esun silky silver PLA - windows, landing gears, engine etc...
Color fabb Leaf green PLA - wings, canopy frame
Esun Peak green PLA - body, stair frame
Esun Red PLA - Center line
(Brand unknown)Dark grey PLA - Engine booster, stair, canon, cargo frame
Esun white - frame of logo

Largest part in printing, size = X 51mm, Y 48mm, Z 90mm, After full assembly size= X 90mm, Y m254m, Z 83mm

Total Build Time : 14h / Plastic Weight : 146g

Planet Express Ship - FUTURAMA

GOODesign_Hull_Rear.stl

I designed this little UFO as a playful way to display small plants or dried flowers (but really, it works for just about anything. Crystals, keepsakes, tiny trinkets, or weird little guys) anything you want to give a moment in the spotlight. It’s part vase, part planter, part display stand, and just the right amount of out there.

**This design works with both AMS and non-AMS printers, it's flexible and easy to assemble!**

**Print settings for the vessel if using it as a planter:**
- Suggest a brim
- No support needed
- 15% infill
- 4 walls
- Top shell: 7 layers
- Bottom shell: 7 layers
- 0.4mm nozzle
- 0.2mm layer height

**Print settings for transparent parts like the windows:**
- Suggest a brim
- No support needed
- 100% infill
- 2-3 walls
- 0.4mm nozzle
- 0.2mm layer height

**Print settings for everything else:**
- Suggest a brim
- Support needed for bottom of ship
- 15% infill
- 2-3 walls
- 0.4mm nozzle
- 0.2mm layer height

**Use 3MF file if you want to see the printing orientations**

**PLA Used:**
- Transparent Neon: https://www.matterhackers.com/store/l/pro-series-pla/sk/MRP7Y07L?aff=7646
- Vivid Tangerine: https://amzn.to/42Towtk
- Transparent Blue: https://www.matterhackers.com/store/l/pro-series-pla/sk/M3PUVADS?aff=7646
- Sage Green: https://www.hatchbox3d.com/products/hb-pla-1kg1-75-sgrn

**Assembly:** https://youtu.be/_-W_iHPZOhE



Kitsch UFO Vase – Retro Planter for Dried Flowers, Crystals, Trinkets | Quirky Sci-Fi Home Decor

pixelandpapier__ufo_vessel__window_trim.stl

Blast off across the stars in the Gummi Ship with this model! The Gummi Ship is assembled using plastic glue with square alignment pins as well as 1/2" sections of spare filament (to align the white wings to the orange wing block).

Please note that the following .stl files will need to be printed in mirrored pairs if not using the included 3mf:
- Orange Wing Block
- Red Side Pipe Cap
- White Wings
- Yellow Side Pipe

In addition, the Square Pin Master is sized to be a snug fit. Depending on your printer and slicer settings, you may need to make minor adjustments to the size and tolerances to assemble your Gummi Ship.

_These .stl files are for individual use only. Selling or distributing .stl files from this pack is strictly prohibited. Selling physical prints of this model is prohibited without an active Master Seller membership_

Kingdom Hearts Gummi Ship

Engine Block.stl

This is a 3D-Printable model kit of the Red 3 Hero X-Wing model in 1/24 studio scale.

Designed with meticulous attention to detail, the use of the latest technologies like photogrammetry and with the originally used kit parts in hand, every curve, every panel line and every detail has been faithfully recreated to be as accurate as possible to the Red 3 Hero model, that was used for filming in the first STAR WARS movie.

With this STL set you can build your own studio-model-accurate replica of Biggs Darklighters Red 3 X-Wing.
But you can of course paint it in any desired color scheme and call sign you want. The included templets for the call sign markings will help you with that.

The last eight pictures show the main differences between Red 3 and Red 5.

May the force be with you!


**Features**
- 1/24 studio scale (studio scale = the size they used for the filming miniature)
- Articulated S-foils.
- Recesses for magnets in the wing mechanism to easily install the wing covers.
The magnets also make closing the wings more tactile and help keep the wings in horizontal position. 
Recesses for magnets in the wing tips to help keep the wings closed.
- Articulated targeting computer.
- Astromech droid with turnable head (R2, R4 and R5)
- 3 Pilots 
   - Live Action Pilot
   - Live Action Pilot with raised hand
   - ILM-Style Pilot
- 2 Cockpits 
   - Live Action Cockpit
   - ILM-Style Cockpit
- The Live Action Cockpit has 0,6mm holes for fiber optics
- Cable routing for engine lighting integrated in the wings
- The finished model can be mounted on a threaded stand 
- 3D-Printable templates to paint Call Sign Markings (Red3 and generic 1-12) included
- Optional Parts for CNC to make out of metal


**Data**
Length: 560 mm / 22 in
Width: 460 mm / 18 in
Hight (with S-foils locked in attack position): 190 mm / 7.5 in
74 STL-files for 3D printing (+ some Alternative Parts)


**Info**
You purchase digital STL-files for 3D printing!
All files are developed for resin printing. 
All files are tested, successfully resin printed and assembled.
Recommended printer build volume for the native scale: 192x120x250 mm (WxDxH)
(Min. required printer build volume: 192 x 120 x 200 mm (WxDxH))

Print the wings and the fuselage with engineering resin (or similar that has little to no flex) to prevent any sagging. Don’t use an ABS-like resin.
Cure the wings and the fuselage very thoroughly immediately after printing for at least 20-30 minutes (washed of course).

My resin recommendation: https://amzn.to/454ywQd


**Join the NerdMaker Community**
[YouTube](https://www.youtube.com/@DominicSchwarz?sub_confirmation=1)
[Discord ](https://discord.gg/9jppu3AxJK)
[Instagram ](https://www.instagram.com/nerd_maker_engineer)
[Facebook ](https://www.facebook.com/nerdmakerengineer)


**License**
A Commercial License, to sell 3D-Prints of my Models, is available here:
[Patreon ](https://www.patreon.com/NerdMaker)

Model-X MK II 1/24 Studio Scale Red 3

Droid Strip.stl

These are fun rockets with boosters that extend on take-off. I designed two sizes and each contain two parts: the main rocket body and the ‘boosters’.

I've included the following STL models:
Large Rocket (complete)
Large Rocket (body only)
Large Rocket Booster Insert (a set of 4)
Small Rocket (complete)
Small Rocket (body only)
Small Rocket Booster Insert 

3D PRINTING SETTINGS
Layer Height 0.2mm
PLA works great
15-20% Infill

Dimensions of Large Rocket: 4in x 2 3/8in
Dimensions of Small Rocket: 3 1/4in x 1 7/8in

*Supports are needed for the larger rocket at the base around the outside rings of the boosters.  (Make sure not to include supports inside the booster chambers because you need to keep those clear to drop the boosters in when you pause the print:)

There are two ways you can print these rockets:
1. Print the complete rocket 
2. For different color rocket and boosters, print the boosters first, print the rocket second pausing at layer height 15.6mm for the large rocket and 30.6mm for the small rocket, drop the boosters in and then continue printing. 

Have fun printing these…they’re a blast 🚀

Rocket with Boosters (2 sizes)

Large Rocket (complete).stl

Discover an awe-inspiring low-detail 3D model of SpaceX Starship launch on THANGS. This tabletop miniature vehicle model is ideal for space exploration enthusiasts and tabletop game lovers. Crafted meticulously based on the iconic SpaceX Starship, the 3D model includes an excellent rendition of the 'liftoff explosion', adding another level of detail to your 3D printing project. Note, the starship fits tightly onto the explosion scene, so it's suggested to adjust the tolerances in your slicer for a perfect fit, although it works perfectly as-is. 

**Print Settings:**

Layer height: .2 (bigger will work)

Walls: 2

Brim: yes

Supports: optional ( I used them but it will work without them it just may require some cleaning up)

Infill: 15% ( more is fine I wouldn't recommend less though)

**Material:**

PLA, PETG, and ABS all should work

Starship: Overture black PETG

Explosion: transparent red PETG (Idk the brand)

 

Thank you for taking the time to read and (hopefully) print this model if you have any problems or issues please just comment and I will try to get back to you asap. Again thanks for checking this out.

SpaceX Starship Launch

starship explotion-7.stl

Prepare for Take Off with the third installment in my Rocket series! The lines on Rocket 3 take inspiration from Space Mountain at Disneyland.
 
This model is printed with the following materials:

- [Panchroma™ Matte PLA (Charcoal Black)](https://us.polymaker.com/products/panchroma-matte?variant=43631458091065?aff=1133)
- [Panchroma™ Matte PLA (Cotton White)](https://us.polymaker.com/products/panchroma-matte?variant=43631458123833?aff=1133)


_These .stl files are for individual use only. Selling or distributing .stl files from this pack is strictly prohibited. Selling physical prints of this model is prohibited without an active Master Seller membership_

**Come hype it up with us on Discord if that's your thing: https://discord.gg/HqbZvqgRB**

Rocket 3

Rocket 3.stl

The fourth installment in my Rocket series takes heavy inspiration from the trailer for Fantastic Four: First Steps! Depending on your printer settings and tolerances, glue may be needed for the assembly process. (Pressure should be applied to make the 4 insert flush with larger pieces)

This model is printed with the following materials:

- [Panchroma™ Metallic PLA (Metallic Blue)](https://us.polymaker.com/products/panchroma-metallic?variant=44228511727673?aff=1133)
- [Panchroma™ Metallic PLA (Metallic Silver)](https://us.polymaker.com/products/panchroma-metallic?variant=43595097374777?aff=1133)


_These .stl files are for individual use only. Selling or distributing .stl files from this pack is strictly prohibited. Selling physical prints of this model is prohibited without an active Master Seller membership_

**Come hype it up with us on Discord if that's your thing: https://discord.gg/HqbZvqgRB**

Rocket 4 (Fantastic Four: First Steps)

SIlver.stl

Following up on my [UFO 1](https://thangs.com/designer/Lego%20Log%20Builds/3d-model/UFO%201-1273500) model, here's Rocket 1. Inspired by retro sci-fi spaceship design, this model stands just about 7 inches tall when fully assembled and is designed to print without the use of support material.

If you download and print this model, please share the finished project as a make and tag me if you post on social media! The opportunity for color customization of the parts has me excited to see what fellow master builders do with it.

_These .stl files are for individual use only. Selling or distributing .stl files from this pack is strictly prohibited. Selling physical prints of this model is prohibited without an active Master Seller membership_

**Come hype it up with us on Discord if that's your thing: https://discord.gg/HqbZvqgRB**

Rocket 1

haul.stl

Get ready for launch (and a fun printing project) with Rocket 2. Inspired by retro sci-fi spaceship design, this model stands just about 9 inches tall when fully assembled and is designed to print without the use of support material.

If you download and print this model, please share the finished project as a make and tag me if you post on social media! The opportunity for color customization of the parts has me excited to see what fellow master builders do with it.

[Rocket 1](https://thangs.com/designer/Lego%20Log%20Builds/3d-model/Rocket%201-1281867)
[UFO 1](https://thangs.com/designer/Lego%20Log%20Builds/3d-model/UFO%201-1273500)

_These .stl files are for individual use only. Selling or distributing .stl files from this pack is strictly prohibited. Selling physical prints of this model is prohibited without an active Master Seller membership_

**Come hype it up with us on Discord if that's your thing: https://discord.gg/HqbZvqgRB**

SPACESHIP

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Model-T Avenger - 1-48 and 1-72 scale

Model-X Cockpit Diorama 1/6

Model-X MK I (1/12 Scale)

Planet Express Ship - FUTURAMA

Kitsch UFO Vase – Retro Planter for Dried Flowers, Crystals, Trinkets | Quirky Sci-Fi Home Decor

Kingdom Hearts Gummi Ship

Model-X MK II 1/24 Studio Scale Red 3

Rocket with Boosters (2 sizes)