**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

_You cut a striking figure where the light and shadow meet.  To observe from just one angle leaves the picture incomplete_  

_The Trysta is for you_

The Trysta (Tris-tuh) Pendant Light graces each room with modern elegance.
 
The clean, ribbed design complements a wide range of aesthetics, while the vertical pattern both hides and accentuates the curves that lie within.

_What's holding you back?  Rendezvous with destiny_

**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

The Trysta represents the third design in the Mimetics3D Home Decor collection.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Trysta - Vase Mode Pendant Light with Bambu 3MF

The Trysta - Vase Mode Pendant Light_Bambu by Mimetics3D.stl

**SKEWBITS** is an original puzzle game designed specifically for 3D printing. Fit the four swiveling Skewbits into various silhouettes. The premise is simple, but you may be surprised by how challenging the problems can get!

---

This is the **Premium Set** for SKEWBITS v2.0. Download includes:
- game board, bits, and problems 001-010
- premium versions of board, extra bits, and storage cases
- PDF solution guide

**_Additional files:_**
- [Preview Set (free)](https://than.gs/m/1063419?affiliateCode=MAKE)
- [Problems 011-015](https://than.gs/m/1063431?affiliateCode=MAKE)
- [Problems 016-020](https://than.gs/m/1063432?affiliateCode=MAKE)
- [Problems 021-025](https://than.gs/m/1063433?affiliateCode=MAKE)
- [Problems 026-030](https://than.gs/m/1063434?affiliateCode=MAKE)
- [Problems 031-035](https://than.gs/m/1063435?affiliateCode=MAKE)
- [Problems 036-040](https://than.gs/m/1063436?affiliateCode=MAKE)
- [Problems 041-045](https://than.gs/m/1063437?affiliateCode=MAKE)
- [Problems 046-050](https://than.gs/m/1063438?affiliateCode=MAKE)
- [Full Set (premium set + problems 001-050)](https://than.gs/m/1063421?affiliateCode=MAKE) _*single purchase_
---

This is _version 2.0_ of the game, with many exciting upgrades:
- All parts newly redesigned and 50 problems in total!
- The 'bits' have larger hinges that are stronger, easier to print, and fit into the problems more visibly. 
- The bits and problems can no longer be placed upside down by accident. 
- Everything was scaled up 120% so the bits are easy to pick up an manipulate by all hands big and small. 
- The problems have been redesigned to use less material but maintain the necessary rigidity
- I've moved the number labels to the front to make them much more clear. 
- I've rearranged some of the problems so the difficulty increases more progressively at first.
- Thanks to the brilliant solver program by [Darci Peoples](https://darcipeoples.com/), I've changed many of the problems to have fewer solutions, making certain problems significantly more challenging!
- The updated solution guide PDF is attached, including problems 001-050

[Watch my video about version 2.0](https://youtu.be/aLKqzI0Va5E)

---

**_Printing Guidelines_**
- bits : 0.16mm layer height, 2-3 walls, 0.4mm nozzle, 15% infill
- problems : 0.16-0.25mm layer height, 1 wall, 100% infill; *printing the first layer with one wall can help with bed adhesion of the number labels*
- board : 0.16mm layer height, 2-3 walls, 15% infill; *for better grid visibility swap filaments at 1.5mm layer height
- cover : _'wLogo'_ version is two parts. Print combined using a multicolor printer or using [Multipass Multicolor Printing](https://makeanything.design/multipass-multicolor/) technique for single extruders.
- board_premium : filament swap at 8.2mm height for better grid visibility. _'TPUgrip'_ can be glued to the bottom for a nonslip board, printed with TPU 95a or similar flexible filament. Use [E6000](https://amzn.to/3UIOdso) adhesive or similar.
- case : use _'size20'_  together with _'Sleeve_Wide'_ or _'size30'_ with _'Sleeve_Tall'_. Wide sleeve holds 21 or 20 problems with the Handle, Tall sleeve holds 27 or 26 problems with Handle. Handle can be used loose (slide in from the bottom of the sleeve) or glued into place.
---

Photographed models were printed using PolyTerra Matte PLA [(US Link)](https://bit.ly/polyTerra) Also on [Amazon](https://amzn.to/3PHOxFA)

SKEWBITS v2.0 Puzzle Game // Premium Set + Problems 001-010

bit_A_red.stl

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out the latest 3 table lamps here:
Stria Table Lamp: https://than.gs/m/1049903
Trysta Table Lamp: https://than.gs/m/1049896
Hestra  Table Lamp: https://than.gs/m/1049906**

The Stria (Stry-uh) Table Lamp adds a touch of modern elegance to any room.
 
The clean, ribbed design complements a wide range of aesthetics.

You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.
 
This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**For some fun pendant lights, check out:
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980
The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**

For some spookier decor check out:
**Faces Of Death Bowl - Skull Bowl - https://than.gs/m/1046122**

**Safety First**
Intended for use with **9 watt LED Lights**.  Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
Base and Cap print in regular mode
0.55 mm wall thickness
8 bottom shell layers. 

100% Scale
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Stria Table Lamp - STL and Bambu 3MF

Stria_PendantLamp_VaseMode_Bambu.3mf

A nice little hand brush and dust pan set to keep your place tidy! This small variation has a brush that is roughly 120 mm wide with 60 mm bristles. The dust pan is 145 mm wide.

**_Printing Guidelines_**

Printing the brush requires a well tuned printer and proper slicer settings to successfully create the long bristles using bridging. I suggest a 0.4mm nozzle and Classic rather than Arachne wall generator. Slow bridge speed, high cooling, and lower extrusion temperatures can all help get clean bridging. You may want to first print the smaller [Detail Dusting Brush](https://than.gs/m/1044850?affiliateCode=MAKE) to make sure your settings are appropriate before trying this larger print.

The handles should be fine with your default print settings. Six [6 mm x 3 mm neodymium disc magnets](https://ebay.to/3kMB1A4) can be [glued](https://amzn.to/44LMqVm) into the handles so they stick together for storage (make sure to get the magnet polarities right!)

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab Marble PLA and Purple ABS](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


Small Brush & Dust Pan

Small_Brush.stl

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

_Twisting waves of passion move beneath your calm, organized exterior.  The Hestra is for you_
 
The Hestra (Hess-truh) Pendant Light brings a modern vibe with a subtle twist

The clean, ribbed design complements a wide range of aesthetics, while the six underlying waves evoke a more dynamic sense of motion.

_Why hide who you are?  Let your passion shine through_

**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

The Hestra represents the second design in the Mimetics3D Home Decor collection.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**



**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Hestra - Vase Mode Pendant Light, Bambu 3MF

The Hestra - Vase Mode Pendant Light by Mimetics3D.stl

Add a touch of nostalgia to your desk with this retro typewriter-shaped sticky note dispenser. It holds accordion-style sticky notes, so you always have one ready to grab. The keyboard isn’t just for looks as it works as a fidget-friendly clicker for those moments when you need to stay focused.

It’s easy to assemble with no complicated setup. Just snap the parts together and you’re good to go. Designed to work with both AMS and non-AMS printers, it’s a fun and functional addition for writers, office workers, and anyone who loves unique desk accessories.

A great mix of style, practicality, and a little fidget-friendly fun!

**With options for both AMS and non-AMS printing, it's flexible and easy to assemble!**

**Print Settings**
- A brim isn't required but I recommend using it for the top and bottom components to prevent curling along the edges
- No supports needed
- 10% infill
- 2-3 walls
- 0.4mm nozzle
- 0.08mm layer height for the "Click and Jot" signage, 0.2mm layer height for everything else
Use 3MF file if you want to use your AMS

**Items Used**
Orange: https://www.matterhackers.com/store/l/listing/sk/ME4CUFC6?aff=7646
Dark Yellow: https://amzn.to/4fEIxYf
Terracotta: https://www.matterhackers.com/store/l/pro-series-pla/sk/MZEZCLYH?aff=7646
White: https://amzn.to/3CbNBFa
Gold: https://amzn.to/4ioZfMX
Copper: https://amzn.to/4kCyW7v
Tan: https://www.matterhackers.com/store/l/pro-series-pla/sk/MZE7T0ST?aff=7646
Red: https://amzn.to/4ioZozZ
Sticky Note: https://amzn.to/4kDwC04
Kailh Jade Switch: https://amzn.to/3Y5lbE3

**Assembly Video:** https://youtu.be/cgcJEPiv4Lw

Retro Typewriter Sticky Note Dispenser – Fidget Clicker Keyboard, Easy Desk Organizer

pixelandpapier__typewriter_note_dispenser__top.stl

Imagine a charming piece of art that brings the nostalgic beauty of vintage Victorian cakes right into your home. **I dedicated a great deal of time to ensure hassle-free printing so there's no supports needed and fully compatible with both AMS and non-AMS printers.** Beyond being a visual treat, it also serves as a delightful container for your treasured trinkets and keepsakes!

**No AMS required**

**Print Settings**
- Brim required. I suggest using an inner brim.
- No supports required
- 15% infill
- 2-3 walls
- 0.4mm nozzle
- .2mm layer height
- Use 3MF file if you want to use your AMS

**Items Used:**
White: https://amzn.to/3CbNBFa
Sea Breeze: https://amzn.to/3DmZh8j
Red: https://amzn.to/41bYoru
Peach: https://amzn.to/3QzInql
Tan: https://www.matterhackers.com/store/l/pro-series-pla/sk/MZE7T0ST?aff=7646
Pink: https://amzn.to/4hJLeJt

**Assembly Video:** https://youtu.be/NG5QxDOq55k



Vintage Victorian Cake Container: Decor, Keepsake, Gift, Retro, Kitsch

pixelandpapier__vintage_cake_container__decorative_cream.stl

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

 
**Check out the latest 3 table lamps here:
Stria Table Lamp: https://than.gs/m/1049903
Trysta Table Lamp: https://than.gs/m/1049896
Hestra  Table Lamp: https://than.gs/m/1049906**


_Twisting waves of passion move beneath your calm, organized exterior.  The Hestra is for you_
 
The Hestra (Hess-truh) Table Lamp brings a modern vibe with a subtle twist

The clean, ribbed design complements a wide range of aesthetics, while the six underlying waves evoke a more dynamic sense of motion.

_Why hide who you are?  Let your passion shine through_



**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**For some fun pendant lights, check out:
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980
The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**


**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
The lamp shad prints in Vase Mode/Spiralize/Spiral Vase Mode
The Base and cap print regularly without supports.  
**The base should be printed upside down**
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Hestra Table Lamp - Vase Mode STL and Bambu 3MF

The Hestra - Vase Mode Pendant Light Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  
 
**Check out the latest 3 table lamps here:
Stria Table Lamp: https://than.gs/m/1049903
Trysta Table Lamp: https://than.gs/m/1049896
Hestra  Table Lamp: https://than.gs/m/1049906**

_You cut a striking figure where the light and shadow meet.  To observe from just one angle leaves the picture incomplete_  

_The Trysta is for you_

The Trysta (Tris-tuh) Table Lamp graces each room with modern elegance.
 
The clean, ribbed design complements a wide range of aesthetics, while the vertical pattern both hides and accentuates the curves that lie within.

_What's holding you back?  Rendezvous with destiny_

**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf files optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**For some fun pendant lights, check out:
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980
The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode for the Lamp Shade
Regular printing for the Base and Cap
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Trysta Table Lamp - STL and Bambu 3MF

The Trysta - Vase Mode Pendant Light_Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

The Flustra (Fluss-truh) Pendant Light brings a modern vibe with a subtle twist

The clean, ribbed design complements a wide range of aesthetics, while the ripples underneath evoke a more dynamic sense of motion.


**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**



**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Flustra - Vase Mode Pendant Light (Large), STL & Bambu 3MF

The Flustra - Vase Mode Pendant Light (Large)_Bambu by Mimetics3D.3mf

A nice general purpose cleaning brush and dust pan set to keep your place tidy! This large variation has a brush that is roughly 180 mm wide with 95 mm bristles. The dust pan is 215 mm wide.

**_Printing Guidelines_**

Printing the brush requires a well tuned printer and proper slicer settings to successfully create the long bristles using bridging. I suggest a 0.4mm nozzle and Classic rather than Arachne wall generator. Slow bridge speed, high cooling, and lower extrusion temperatures can all help get clean bridging. You may want to first print the smaller [Detail Dusting Brush](https://than.gs/m/1044850?affiliateCode=MAKE) to make sure your settings are appropriate before trying this larger print.

The handles should be fine with your default print settings. Six [6 mm x 3 mm neodymium disc magnets](https://ebay.to/3kMB1A4) can be [glued](https://amzn.to/44LMqVm) into the handles so they stick together for storage (make sure to get the magnet polarities right!)

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab Marble PLA and Purple ABS](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


Large Brush & Dust Pan

Large_Brush.stl

The **PLEIADES Soap Cover** is a quick and clever way to elevate your boring soap bottle. This fits bottles up to 57 mm x 83 mm x 103 mm tall with a 28mm opening.

---

My **PLEIADES** series of prints are designed to be printed in vase/spiral mode in your slicer. I suggest printing this model with a **0.4 mm nozzle width**. Adjust bottom solid layers to be 1.6 mm thick (or the maximum number of layers before the hole is covered). No top layers. **Make sure your slicer is not set to close small gaps.** In BambuStudio I set the _'Slice gap closing radius'_ to 0 mm

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Fillamentum PLA Extrafill Sky Blue](https://bit.ly/FM-xtra) (also at [MatterHackers](https://bit.ly/xtrafill)).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


PLEIADES Soap Cover // 57x83x103

PLEAIDES Soap Cover 57x83x103.stl

**Print-In-Place, No Supports, Articulating Fidget Toy**

Looking to hang out with your gnomies on St. Patricks Day?

This St Patty's Flexi Gnome is getting some stretching in to prepare for the celebrations.


He has 2 separate poses.  He can:
- Sit in a split-leg position
- Stand straight up on 2 legs


While waiting on some test prints of more complicated Snap-Flex designs, I started playing around with simpler flexis for sculpting practice.  I realized that there are other ways to make fun posable models, and that not ALL of my models need to be Snap-Flex designs.

**Check out some other simple flexis here:**

**Flexi Pug - Articulated Dog, Style #1: https://than.gs/m/1027312
Flexi Pug - Articulated Dog, Style #2: https://than.gs/m/1027678
Flexi Pug - Articulated Dog, Style #3: https://than.gs/m/1027452**

Additionally, check out another St. Patrick's Day design:
**Little Lucky Rubber Ducky, a St. Patty's Leprechaun Duck - https://than.gs/m/1024753**

Models like this give me an opportunity to continue building my skillset and releasing models while I wait for my printers to finish prototypes of more complex designs.


Please be sure to check out my other articulated dragon and articulated snake designs.

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
**Good Bed Adhesion Required - Consider using glue stick** or a brim


St Patty's Flexi Gnome - Articulated Fidget Toy

StPatricks_StPattysGnome.stl

This large pot is the first in my **VESUVIUS Collection**, which features dense herringbone ribs to increase strength while creating a dramatic form.

VESUVIUS 001 is 250 mm tall and 250 mm in diameter at the top. The bottom footprint has a 190 mm footprint. This was designed for use with my [250 mm Floating Drip Tray](https://than.gs/m/1027171?affiliateCode=MAKE) to catch excess water runoff.

**_Printing Guidelines_**

The **VESUVIUS** series of prints are designed to be printed in vase/spiral mode in your slicer. For full scale I suggest printing with a **1 mm nozzle width** (even with a 0.4mm nozzle) and 1.6mm of solid bottom layers. No top layers. **Make sure your slicer is not set to close small gaps.** In BambuStudio I set the _'Slice gap closing radius'_ to 0 mm

For the 'wHole' version of the vase mode print, use the maximum number of solid bottom layers before the holes are covered to avoid interfering with the spiral printing. You can also print the version without holes and simply drill/cut your own drainage holes in the bottom after printing if you plan on growing live plants.

I've also included a 'Solid' version for standard printing, with roughly 3mm thick walls. This will be extra strong, but uses much more material, and I've found the 1mm vase mode version to be sufficient, even at this large size.

---

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab PLA Basic Gradient (Solar Breeze)](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_

VESUVIUS Pot 001 // Large Vase Mode Planter

VESUVIUS_001_Solid.stl

VESUVIUS_001_1mmVasemode_wHoles.stl

VESUVIUS_001_Solid_wHoles.stl

**Print-In-Place, No Supports, Articulating Fidget Toy**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**
   
**Check out the latest Mimetics3D Model, [Little Lucky Rubber Ducky](https://than.gs/m/1024753)**

_A little snek who slithers so 
surveys the scene and says that though
the seasons slip swiftly away 
some other things are here to stay._ 
 

Slick the Snek is super excited to slip into the Snap-Flex collection.  

Slick was originally going to be showing off the new **Snap-Flex Twist** experimental joint, but his buddy **[Sly - Articulated Snake](https://than.gs/m/1025111)** is doing that instead.

Slick is the 20th creation in a series of Snap-Flex models by Mimetics 3D, and is available for free for a limited time.

 
**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the model to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 
 
Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart
 
**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels of this model to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Slick, Articulated Snake:**
https://than.gs/m/1018173
**Medium Tolerance Slick, Articulated Snake:**
https://than.gs/m/1018181
**Loose Tolerance Slick, Articulated Snake:**
https://than.gs/m/1018185

Please try out each to see what works best for you, and let me know which version you prefer!

Make sure to revisit frequently for more thrilling Snap-Flex models to come. I'm eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

This mini little monster is excited to bring a bit more love into your life

**Other Models:**
For another articulated Valentine's friend, check out this little Heart Axolotl:

**Tight Tolerance Alotl Love:**
https://than.gs/m/994472
**Medium Tolerance Alotl Love:**
https://than.gs/m/994480
**Loose Tolerance Alotl Love:**
https://than.gs/m/994484

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
**Good Bed Adhesion Required - Consider using glue stick** or a brim

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.


Slick - Articulated Snake Snap-Flex Fidget (Loose Joints)

Slick_articulatedSnake_Loose.stl

The Tsugite Cube has reached unprecedented extremities with this 4x4 version of the confounding puzzle cube series. 

Join all 31 pieces in the correct order and orientation to create a continuous loop in the form of a solid 4x4 cube. The Kawai Tsugite joint connects in 3 different orientations, so this isn't your average packing puzzle! 

As a helpful hint, no like colors will touch when printed in 6 colors... Consider that a part of the puzzle since it's already difficult enough, but if you feel like an even more extreme challenge, you can print it all in one color.

This download also includes a flashy Special Edition 4x4 Stand, along with the default cube stand. There is also an STL of the entire assembled puzzle if you need help solving, or check out my full [Solution Video on YouTube](https://youtu.be/yZwMSwlxIy0).

---

**_Printing Guidelines_**

Print at 0.16mm layer height with 3 shells and 0% infill, 5 top and 5 bottom solid layers. No supports required! The puzzle parts are divided into 6 groups, where no like colors will be touching for the solved puzzle. You can split the models into parts within your slicer if you wish to print/color separately, or need to rearrange parts for whatever reason.

The SE_Stand is a somewhat difficult print without supports. I used fuzzy skin with 0.2mm thickness and point distance to hide any wobble artifacts near the top and as a general aesthetic. I printed with 4 shells, 0 top layers, and 15% lightning infill. You may also need a brim or minimal supports to improve printability. The basic stand is much easier to print!

4x4 Tsugite Cube Puzzle

4x4_White.stl

This cozy little living room set was made to bring midcentury charm to your miniature scenes. It includes two statement chairs (a miniature cane cantilever chair and a sculptural cocoon chair) alongside a coffee table and side table.

Each piece features soft curves and midcentury inspired lines, designed to mix and match with other 1:12 scale furniture. Whether you're building out a dollhouse, diorama, or a cozy book nook display, this set adds just the right touch of retro comfort.

**No AMS? No problem! I've designed it to work with both AMS and non-AMS printers!**

**Print Settings:**
If you'd like to see the orientation and settings of the print, please take a look at the .3mf file.

_Cane Cantilever Chair_
- No brim needed
- No supports needed
- 100% infill for the leg frame, 15% infill everywhere else
- 2-3 walls
- 0.4mm nozzle
- 0.12 - 0.2mm layer height

_Cocoon Chair_
- No brim needed
- No supports needed
- 60% infill for the pedestal base, 15% infill everywhere else
- 2-3 walls
- 0.4mm nozzle
- 0.12 - 0.2mm layer height

_Coffee and End Table_
- No brim needed
- No supports needed
- 15% infill
- 2-3 walls
- 0.4mm nozzle
- 0.12 - 0.2mm layer height

**PLA Colors:**
- Applesauce: https://amzn.to/3RmjTBw or https://www.hatchbox3d.com/products/3d-pla-1kg1-75-apsc
- White: https://amzn.to/3FORvWl or https://www.hatchbox3d.com/products/3d-pla-1kg1-75-wht
- Butter Yellow: https://amzn.to/4jAvsBl or https://www.hatchbox3d.com/products/3d-pla-1kg1-75-mat-bylw
- Metallic Finish Brown: https://amzn.to/3XJFnMi or https://www.hatchbox3d.com/products/3d-pla-1kg1-75-shny-brn
- Wood: https://amzn.to/4i6uYla or https://www.hatchbox3d.com/products/3d-wood-1kg1-75
- Wood Brown: https://amzn.to/4idTqBd or https://www.hatchbox3d.com/collections/pla-1-75mm/products/3d-wood-1kg1-75-brn-b075dyqkq9

**Assembly Video:** https://youtu.be/Hq-uz4rXF0Q

**Important Note: Not suitable for young children. Contains small parts that may pose a choking hazard.
**


Midcentury Miniature Living Room Furniture Set – Cane Chair, Cocoon Chair, Tables, 1:12 Scale

pixelandpapier__mini_living_room_set__AMS.3mf

pixelandpapier__mini_living_room_set__cane_chair_cane.stl

This print-in-place parametric box is available in two versions and can be customized to your desired dimensions. The package includes source files for Fusion 360, allowing you to set your preferred dimensions, and the model will automatically adjust.For more on parametric design, check out this helpful video. To create different grid patterns on the model, simply choose your desired infill pattern in your slicer and set the top and bottom walls to 0mm.

Parametric self locking pip box

parametric pip modular box ext.stl

🎉 Exciting News! 🎉

I’m thrilled to re-enter my Bendy Beast model, which previously won first place, into the Thangs Throwback Contest! 🏆

Why You’ll Love the Bendy Beast:

Universally Compatible: Tailored to fit most printers, the Bendy Beast is ready to make its mark in any maker’s collection.
Newbie-Approved: It’s the perfect project for those just dipping their toes into the vibrant waters of 3D printing.
Zero Hassle: Say goodbye to supports! This fully articulated design prints smoothly, letting you focus on the fun.

COPYRIGHT KINDNESS: At Mesh Mayhem, we cherish creativity and respect ownership. Our designs, including the Bendy Beast, are copyrighted for personal enjoyment.

We encourage personal use and sharing your journey with us, but commercial use requires a special touch – a Mesh Mayhem commercial license. So, if you’re looking to sell, let’s make it official! Our membership offers you the license you need, plus a treasure trove of perks.

Join us, and let’s create magic together!

Please, no commercialization without a license. Let’s play fair and have fun!

Did we catch your eye? We’d love to see your Bendy Beast come to life! Share your prints in the comments and spread the joy.

BendyBeast Articulated Dragon #Throwback

Articulated Dragon BendyBeast Mesh Mayhem.stl

[_**V2 is now available HERE**_](https://than.gs/m/1377006?affiliateCode=MAKE)

ITALIC is an eccentric watering can featuring a playful skewed profile. The enclosed container is filled through an opening in the top of the handle, which can also be covered with your thumb while pouring to regulate flow. Like any good fancy designer product, it's slightly awkward to hold. How will you pick it up? :P

**_Printing Guidelines_**

The walls of this container are 1.2 mm thick, and only the handle portion is solid. I suggest printing with a high wall count (5+) to ensure that the thin handle won't snap off.  You also need to ensure that your printer can create watertight models, otherwise this won't be quite as useful. I used default print settings on my Bambu Lab X1-Carbon with ABS and it worked out!

Download includes a version with minimal supports since the handle is unsupported for much of the print, as well as a version of just the watering can. In either case, I would suggest a substantial brim to help with bed adhesion. 

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab Mint ABS](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


No Supports

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

The Trysta - Vase Mode Pendant Light with Bambu 3MF

SKEWBITS v2.0 Puzzle Game // Premium Set + Problems 001-010

Stria Table Lamp - STL and Bambu 3MF

Small Brush & Dust Pan

Retro Typewriter Sticky Note Dispenser – Fidget Clicker Keyboard, Easy Desk Organizer

Vintage Victorian Cake Container: Decor, Keepsake, Gift, Retro, Kitsch

St Patty's Flexi Gnome - Articulated Fidget Toy

Slick - Articulated Snake Snap-Flex Fidget (Loose Joints)

4x4 Tsugite Cube Puzzle

Midcentury Miniature Living Room Furniture Set – Cane Chair, Cocoon Chair, Tables, 1:12 Scale

Parametric self locking pip box

BendyBeast Articulated Dragon #Throwback