Long Beard Gnome Ornament Set

LongBeardGnomeOrnament4Color3MF_FunFam3D.3mf

A-Frame Cabin Lamp - No Supports, No AMS - Christmas Day 13 - Light - Lighting

a-frame-cabin.stl

Flowery Whatsit Ornament Suncatcher

*What is it?*
This is part of a series of designs that were originally intended as Christmas tree ornaments and I later found also made great suncatchers for any time of year (when printed with transparent filament/resin). This is the second in the series to be published.

Beyond that, what is it? Well, it's kind of a snowflake pattern (5 points instead of 6), kind of a star, kind of flowery, and bears a large resemblance to gothic architecture. Mostly, it's just a cool geometric design that I enjoy looking at.

*How to Hang it*
I've included two small, well hidden loops behind one of the arms so you can tie coat thread on them and hang it up. See the detail photo included above. They are really small and very well hidden.

**Print Settings**
You shouldn't need a raft or brim. 

*Print Time*
Depending on the wall thickness, these printed in 2-3 hours for me.

*Thickness*
If you want to use these as Christmas ornaments, I recommend trying to print this with 1 line (0.4mm) walls. As a suncatcher, it looks good with 1 or 2 line walls (I prefer 2). I needed to make the walls with 2 lines (0.8mm) to get a good print from the TTYT3D Silky Orange. I set the top/bottom thickness to 0.3mm.

You probably have your printer set up to print 1.2mm walls and top/bottom thickness. Don't use those settings for this design unless you plan to use it as a paperweight. If you forget to change them, cancel the print and start over.

*Flow*
I increased the flow to 110% for the outer walls and 105% for the inner.

*Infill*
This doesn't need any infill. Seriously. Don't add it unless you want to use this as a paperweight.

*Speed*
I print the first layer at 18mm/second. That makes sure that the complicated design gets good bed adhesion without a raft or brim. It also adds less time to the print and less clean-up than using a raft or a brim. If you have a cold bed, you might need the raft or brim anyway.

For all other layers, I use:
* 30mm/second outer wall speed
* 40mm/second inner wall speed
* 60mm/second overall speed

Togepi Egg Easter Egg

Togepi-egg-Top.stl

Swoop 1 Christmas Stretch Ornament 2024

Stretch Swoop 1 Whole v2.stl

Holiday Kiss Cookie Ornaments

KissCookie1STL-FunFam3D.stl

Gnome Ornament Set

2025GnomeOrnamentCowboyHatSTL_FunFam3D.stl

Christmas Tree For Free

1.stl

Swoop 1 Christmas Bulb 2024

Bulb Swoop 1 Final.stl

Tippi Tree Santa + Finch Santa

Tippi_Santa_Hat_Combined.stl

Snowflake Ornaments

Snowflake Ornaments Plated.3mf

Ornamental Bauble 2022 (#5)

Ornamental Bauble 2022 (5).stl

Agumon

Agumon-Ornamental.stl

Gingerbread Cookie Ornaments Set 6

GingerbreadOrnamentSet6-1-STL-FunFam3D.stl

Easter Egg Sword!

EGG SWORD.stl

Super Annoying Gift Box - iPhone, Android, ??, This box has 130 bolts, three layers of fun. 

MAIN BOX - ARTICULATING IPHONE.stl

Closed Lattice Christmas Topper

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**WHAT IS IT?**
This is a topper for small to medium Christmas trees. It will work well on trees that are anywhere from about 4 feet (1.3 meters) up to 7 feet (2.3 meters) tall.

**CHALLENGING PRINT**
If you just got your first 3D printer and are looking for your first thing to print, this isn't it. Using the settings I recommend below, an experienced maker should be able to get a good print without many failed attempts. However, if you are not intimately familiar with the detailed settings in your slicer, add this to your favorites and come back when you have a little more experience. If it's frustrating, it's no fun.

If you're looking for an even bigger challenge, try my Open Lattice Christmas Tree Topper: https://thangs.com/designer/dazus/3d-model/Open%20Lattice%20Christmas%20Topper-472732?manualModelView=true.

**COMMON PROBLEMS PRINTING**
Assuming you use the print settings I recommended below, here are some common problems and possible fixes:
*Comes off bed:* Increase brim/raft size. Reduce print speed. Add more supports.
*Print looks rough:* Reduce print speed.

**PRINT TIME
With my settings, it will take 12-15 hours depending on the exact support and build plate adhesion settings you use.

**PRINT SETTINGS**
*Thickness*

* Layer thickness: .15mm
* Wall thickness: 0.4mm and choose the “alternate extra wall” option so it alternates between 0.4 and 0.8mm walls with each layer (if you're using Cura – other slicers may not have this option). The alternate extra wall seems to prevent gaps in the print while minimizing the overall weight of the ornament.
* Top/bottom thickness: 0.3mm

*Infill*
This doesn't need any infill. Seriously.

*Speed*
You'll want to use slow printer settings to that the print is accurate and to reduce the pull on the thin arms of the topper.

* Overall: 60mm/s
* Outer wall: 20mm/s
* Inner wall: 40mm/s
* Travel Speed: 65mm/sec

*Build Plate Adhesion*
You'll need to use either a brim or a raft. The base of the ornament is a thin, narrow circle. It just won't stay attached to the bed without a little help. I'd use an 8mm brim 8mm or a 15-20mm raft.

*Supports*
I used the custom support plug-in in Cura, choose the “freeshape” option whose icon looks like an extruded star, then chose “arch-buttress” from the drop-down. I attached overlapping supports to both the middle of the large and medium bulbs on all 4 sides. This results in a single support on each of 4 sides that makes contact with the ornament in 2 places. I used 20% gyro infill and a 1 layer wall. 

After the print was done, I found that the supports only just survived the printing process – and if they failed, the whole print would fail. I would now recommend using the “custom” option from the drop-down instead, making the walls 2 layers thick, scaling the width of each support to 150%, and reducing the infill to 8% gyro. Granted, I haven't tested this exact combo, but I know it'll be a lot stronger. The main difference in the “custom” vs. the “arch-buttress” is that the “custom” option provides good lateral support so sideways forces don't break the support in half. The new settings will add about 90 minutes to the print time. However, when this print fails, it generally does it after 75% or more has printed. Adding 90 minutes to the print may save you from printing for 9 hours only to have to start over.

I've attached screenshots from Cura so you can see both options.

If your slicer doesn't have an option for something similar to custom supports, you might try these settings, but I do not know if they will work:

* Overhang angle: 52 degrees
* Support wall line count: 2
* Support pattern: Gyro
* Support density: 8%
* Support placement: touching buildplate

If you do use them, add a support blocker to the center of the model to prevent supports from being added to the central shaft. There's no need for the supports there. It'll only add time to the print while giving you even more supports to remove when the print is finished.

HOLIDAY

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Long Beard Gnome Ornament Set

A-Frame Cabin Lamp - No Supports, No AMS - Christmas Day 13 - Light - Lighting

Flowery Whatsit Ornament Suncatcher

Togepi Egg Easter Egg

Swoop 1 Christmas Stretch Ornament 2024

Holiday Kiss Cookie Ornaments

Gnome Ornament Set

Christmas Tree For Free

Swoop 1 Christmas Bulb 2024

Tippi Tree Santa + Finch Santa

Snowflake Ornaments

Ornamental Bauble 2022 (#5)

Agumon

Gingerbread Cookie Ornaments Set 6

Easter Egg Sword!

Super Annoying Gift Box - iPhone, Android, ??, This box has 130 bolts, three layers of fun.

Closed Lattice Christmas Topper

Gingerbread People Ornament Set

Kernel Krunch Multi-Pack

Candy Cane Egg