Headphone Rest - v3 (for Laptop, Notebook)

The goal of my design is to create some kind of rest or hook for a headphone / headset while you are working on your notebook/laptop.
My headphone was always laying arround and i wanted a cleaner desk.

The headphone rest have to be placed / double tape glued onto the backcover of the notebook/laptop.

The headphone rest can be slided out to hang on your headset to the hook and if you put your notebook/laptop in a bag for travel etc.. you can just simply slide the rest in.

The example pictures will show you where to place it and how to use it :)

If you like my design, i would appreciate it if you buy it to support me for my time to create it and make future designs possible.

Note: Double side tape - i used a 0.8mm thin double sided tape with a width of 30mm (which fits perfect for the design), you may use a 3M or a similar tape from amazon, aliexpress, local store etc.

Befor you glue it onto the notebook/laptop - make sure both have temperatures > 20°C and the spot where you tape it onto the notebook/laptop is free of dirt, dry and cleaned (like with isopropylalcohol ...) to get a nice bond. (Make sure you do not damage the backcover by the material used).

If you like the design, you can fill out the offset surfaces with a white/colored waterproof pencil to give it a highlight.


Print material: PETG (recommended)
Nozzle size: 0.4mm
Layer height: 0.16mm or 0.12mm works perfect. (maybe 0.2mm works too, but i have not tested it since the parts are small)
Print duration: 1 set (base + slider) was 42min on my Prusa MINI+

Postprocessing:
- Place the double sided tape on the back of the base
- Put a very very small dip of grease / oil onto the "inner rails" of the base
- Connect the slider into the base with a little force to "snap in"
- Try to move the slider from side to side, if it runs smooth all good, if not, maybe a little sanding/mechanical smoothing is needed.

Headset Holder Jabra

Headsethalter.stl

Peltor Hearing Protection Spacer

Peltor Spacer.stl

Anime Demon Horns for Headphones Cosplay

demon_anime_horn_002_left.stl

Modern Minimlist Headphone Holder

Headset_25_1.stl

Sculptural Headphone Stand

Headphone Stand, Open Version, THIN.STL

Dino Headset Stand

dino claw3.stl

headset holder on shelf.stl

headset holder.stl

LED Cute Bunny Ears Cosplay

bunny_ears_002_rgb_v9_left.stl

Desk Tray

Desk Tray.3mf

Headset Stand Wall Base

Headset Stand Wall Base.stl

wolf  upper jaw.3mf

wolf  head.3mf

SteelSeries Microphone Wire Stabiliser.3mf

I have a SteelSeries Arctis 1 Wireless headset and my microphone started to break right at the 3.5mm jack.

This stabilizer presses onto the microphone wire with moderate friction fit and encases the entire joint between the wire and the jack, stabilizing the joint and preventing the break from getting any worse.

A single drop of superglue can be helpful if you're inclined to do so, but I don't use it as I'm afraid I'll update this model later and want the new version on my machine.

Print Tips:

Use .12 mm layer height
.4 mm Nozzle
PolyTerra PLA+ (My print)
Use a brim
User Arachne for the most accurate slicing
Model is oriented in the correct print orientation, no supports required
 v

HEADSET

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Headphone Rest - v3 (for Laptop, Notebook)

Headset Holder Jabra

Peltor Hearing Protection Spacer

Anime Demon Horns for Headphones Cosplay

Modern Minimlist Headphone Holder

Sculptural Headphone Stand

Dino Headset Stand

headset holder on shelf.stl

LED Cute Bunny Ears Cosplay

Desk Tray

Headset Stand Wall Base

wolf upper jaw.3mf

SteelSeries Microphone Wire Stabiliser.3mf

Cute Fox Ears for Headphones

Low Poly Design Headphone Stand "TheRock"

Headphone Stand, with Storage

Headphone holder with name

Standing Headphone Stand

Overwatch 2 Version D.Va Headset Printable Model

Ulala form Space Channel 5 cosplay accessories