| Visit [JERRARI3D.com](https://www.jerrari3d.com/) for Instructions and a complete look at the GEN2 collection 
__________________________________________________

A **large** and fully adjustable tray holder that fits under any table, enclosure, or workbench. fits Vorons, XL, etc.

GEN2 Adjustable Steel Sheet Holder - Large

gen2-steel-sheet-holder-sides.3mf

| Visit [JERRARI3D.com](https://www.jerrari3d.com/) for Instructions and a complete look at the GEN2 collection 
__________________________________________________

Modular solution for storing steel sheets under your enclosure or table top. This version if FULLY ADJUSTABLE in width and depth

**Supported Printer Sheet Sizes:**
Prusa Mini, Bambu Lab A1 Mini, and others withing the size range specified.

Minimum sheet size: 175mm wide x 160mm depth
Maximum sheet size: 245mm wide x 235mm depth

This model is part of my GEN2 Modular Rail System and is compatible, stackable, and swappable. This model works well under GEN2 storage drawers as an example. If you have a smaller printer the GEN2 Modular Mini Edition Lack Enclosure Drawers are also compatible with it as well.

**HARDWARE**
• Screwdriver
• Countersunk woodscrews: (Metric: 4x25mm to 4x16mm) or (SAE: #6 or #8 up to 1" long)
• Drill bit that is smaller diameter than the wood screws
• Pen, Marker, or Scratch Awl
• Magnets (Optional): 10x5x2mm or 10x2mm
• M3 nuts
• M3 Screws M3x8 - M3x10

**SEE VIDEO FOR WALKTHROUGH INSTRUCTIONS**

Note: You can also add magnets to the sliding backer slots to create mild attraction to hold steel sheets in place.

**INSTALLING RAILS IF NEEDED**

• The GEN2 Adjustable Steel Sheet Holder requires 3 rail units. The easiest way to add 3 units is by printing a Gen2 Rail Double Rail and a Gen2 Rail Single.

 • Use templates to mark the hole locations on the surface you are mounting the desired sized rail to.

• Drill out marked locations using a drill bit smaller than the diameter of the wood screw you will be using.

• Prep the rail for installation by installing M3 nuts into the hexagonal holes. You can use a M3 screw to position and tighten the nut in place.

• Install the rail using wood screws, use at least 4 screws on the outer corners to mount the single rail and and 6 to mount the double rail. (extra screw holes are available if you plan to stack more than 2 rows of drawers or contents of heavier than normal weight.)

**RECOMMENDED PRINT SETTINGS**
Filament: PLA (PETG or ABS for heavier duty storage)
Nozzle Size: 0.4mm
Print Height: 0.2-0.35mm
Infill: 10-20%

GEN2 Adjustable Steel Sheet Holder

Left Rail and Parts.3mf

Print this adaptor to use [eSun Filament Refills](https://tidd.ly/4qk2xVj) together with Bambu Lab spools. This lightweight but sturdy adaptor ensures a secure fit so your filament doesn't unravel. It prints in under 2 hours using less than 45 grams of filament.

Along with the STL file, I've included 3MF project files for Orca(BambuLabs) and Prusa(Qidi) Slicers with preset settings. Otherwise, you can use the settings below for best results:

---

**_Printing Guidelines_**

- 0.2mm layer height
- 2 Perimeters
- 5 top and bottom solid layers
- Disable 'Extra Perimeters', 'Ensure vertical shell thickness', 'Fill gaps', and  'Detect narrow internal solid infill' to reduce uneccessary infill.
- Set perimeter generator to 'Arachne'
- 0% infill
- Set 'slice gap closing radius' to 0mm
- Enable 'Arc fitting' 

Prints well with PLA or PETG. Using filaments that shrink more, like ABS or ASA may cause a bad fit to the spool.

**Note:** There's a small notch that aligns with one side of the Bambu spool to prevent spinning. Make sure to assemble so they fit together (See last photo).

**Note:** This model is designed for recent eSun refill spools with 55mm height and 92mm inner diameter. Older refill spools may not fit.

---

Photographed model was printed on the [QIDI Q1-Pro 3D Printer](https://qidi3d.com/products/q1-pro-3d-printer?sca_ref=6089281.BQS8d0sJuF) (Also on [Amazon](https://amzn.to/4a1BtS9))*

*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_*. 

eSun Refill to Bambu Spool Adaptor

eSun2Bambu_SpoolAdaptor.stl

Print this spacer to use ['The Filament' refills](https://shop.spectrumfilaments.com/eng_m_THE-FILAMENT-3588.html?filter_price=&filter_traits%5B868%5D=&filter_traits%5B954%5D=961&filter_traits%5B22%5D=&filter_traits%5B1705%5D=&filter_traits%5B1151%5D=) together with Bambu Lab spools. In this case, the filament uses the same size cardboard core, but this  adaptor ensures a tighter fit so your filament stays correctly wound. It prints in under 2 hours using labout 30 grams of filament.

---

**_Printing Guidelines_**

- 0.2mm layer height
- 2-3 Perimeters
- 5 top and bottom solid layers
- Disable 'Extra Perimeters', 'Ensure vertical shell thickness', 'Fill gaps', and  'Detect narrow internal solid infill' to reduce uneccessary infill.
- Set perimeter generator to 'Arachne'
- 0% infill
- Set 'slice gap closing radius' to 0mm
- Enable 'Arc fitting' 

Prints well with PLA or PETG. 

---

**_Assembly_**

Place the refill onto the half of the Bambu Spool with the alignment notch.

Place this spacer with the wider face against the filament, on the opposite side of the refill. The print has a cutout to make space for the inside end of the refill, which sometimes sticks out.. otherwise you can ignore it.

The second half of the Bambu Spool goes through the spacer and the refill core. Press the halfs firmly together while locking them together to ensure a proper connection. This is an intentionally tight fit to keep the filament from tangling on the spool.


FIT

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

GEN2 Adjustable Steel Sheet Holder - Large

GEN2 Adjustable Steel Sheet Holder