Jack the skellington wreath (Updated)

jack skellington wreath with hoop.stl

Minimalist Design Self Watering Plantpot

SW009.stl

PLEIADES Soap Cover // 57x83x103

PLEAIDES Soap Cover 57x83x103.stl

Snow Panda - The Polar Bear

Snow Panda - The Polar Bear.stl

snowflake

snowflake.3mf

Cat christmas tree decoration v2.stl

Hang it in Your christmas tree or somewhere else.

Furfur - Ars Goetia (Pre-Supported)

Furfur.stl

Death Moth (Pre Supported)

Death_Moth.stl

Design Key & Coin Tray

TR020.stl

Ginkgo Vase for Timeless Home Decor

Ginkgo Vase.stl

Double Spiral Christmas Bulb 2024

double spiral bulb v3.stl

Swoop 3 Christmas Bulb 2024

bulb swoop 3 simplified v2.stl

Fouled Anchor Shelf Decor

Anchor Shelf Decor.stl

Berry Flower Vase - Vases & Planters By Lunfardo

Berry Vase.stl

Chunky People Planter Sitting Holding Head / No Supports

People Planter Sitting 1 (With Drainage )f.stl

Spiritual, Know Your Power 1

Spiritual_1.stl

Illusion Cube Ornament Edition || Christmas

Illusion Cube Ornament Edition V1.1.3mf

Diamond Christmas Ball Design 2

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems. It may be a little challenging to print. The key is to get the speed, temperature and flow right for your particular printer/filament combo so the stem prints cleanly at the narrowest point.

I printed this in Matterhackers Translucent Red. It's a nice balance between translucency and reflectivity. For an opaque filament, I'd use a multi-color PLA (like Matterhackers Quantum) or a medium toned silky PLA (gold, red, just use anything that's not really light or dark). Either type of filament would show off the facets nicely.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 110, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm and adding custom settings for the base of the ball that printed it 0.8 mm thick. You can do this by adding a support blocker to the bottom and giving it custom settings of 0.4 mm. Cura adds the two and prints the area within the blocker at 0.8 mm.

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I really relied on the supports for build plate adhesion. I used a brim, but I set it to 3.2 mm gap from the print so it would touch the supports but not the ornament.

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
Support Overhang Angle: 45 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 m above the build plate so that the supports would only be added to the bottom of the ornament.

Diamond Ripple Vase 

A decorative vase made in Fusion 360.  There may be issues printing in spiral mode, so I just printed with 5 walls, zero infill, and no top layers.

Mini Gingerbread Cookie Dragon 

mini gingerbread cookie dragon.stl

DECORATION

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Jack the skellington wreath (Updated)

Minimalist Design Self Watering Plantpot

PLEIADES Soap Cover // 57x83x103

Snow Panda - The Polar Bear

snowflake

Cat christmas tree decoration v2.stl

Furfur - Ars Goetia (Pre-Supported)

Death Moth (Pre Supported)

Design Key & Coin Tray

Ginkgo Vase for Timeless Home Decor

Double Spiral Christmas Bulb 2024

Swoop 3 Christmas Bulb 2024

Fouled Anchor Shelf Decor

Berry Flower Vase - Vases & Planters By Lunfardo

Chunky People Planter Sitting Holding Head / No Supports

Spiritual, Know Your Power 1

Illusion Cube Ornament Edition || Christmas

Diamond Christmas Ball Design 2

Diamond Ripple Vase

Mini Gingerbread Cookie Dragon