ClickCube - Clicker Flushie Cube, Ludo fidget

Cube Center.stl

KWOB Puzzle // Ziggy A

kwob-ziggy.stl

5x5 Puzzle Cube

solution.stl

XYZ Calibration Test - Vase Mode

Quick 10 minute print - 0.3 m of filament

Don't waste your precious time and filament printing a so called “calibration cube”!

This quick print provides clues for all the important features and settings:

Extrusion width
E-steps / rotation distance (X, Y, Z)
Bridging
Cooling
Overhangs
Speed / accelleration
First layer / bed adhesion
Retraction (stringing test, seam test)
Preassure advance / linear advance
Print Settings
1 perimeter
0.2 mm layer hight
3 bottom layers
Disable “Ensure vertical shell thickness” (PrusaSlicer)
No Infill, top layers, brim or supports

**Troubleshooting**
https://www.reddit.com/r/3Dprinting/wiki/troubleshootingandcalibration

Some quick tipps:

_**Extrusion width**_
Check if the thickness of one of the outside walls at the top matches the setting in your silcer
**_E-steps / rotation distance (X, Y, Z)_**
If the outside dimensions are not 20 mm but way off, correct the settings for the affected axis
**_Bridging / cooling_**
If the bridging perimeters in the top center are drooping/sagging, check cooling an bridging settings in your slicer
45° overhangs
If the perimeters in this section are drooping/sagging, check the part cooling and cooling settings in your slicer
**_Speed / accelleration_**
ringing, bulged corners - you may want to reduce speed and/or accelleration (also see Preassure advance / linear advance)
**_First layer / bed adhesion_**
If there are problems with the print adhering to the bed, check if
- the bed is level and parallel to the x-axis
- the bed is clean - no dirt or grease
- the bed temperature is correct
If the print is wider at the bottom (first few layers) than at the top, check your z-offset and first layer settings
**_Retraction (stringing test)_**
If you experience stringing, check your retraction and cooling settings
**_Preassure advance / linear advance_**
If large seam gaps or bulged corners appear, consider tuning your printer firmware settings for preassure advance (Marlin) / linear advance (Klipper)

XYZ Calibration Test

Planetary Gear Cube Fidget Toy by Ruven Bals

Planetary Gear Cube by Ruven Bals.3mf

Print-in-Place Geared Rising Box

Print in Place Geared Rising Box.3mf

Twisty Cube Puzzle

Twisty Cube No Supports.3mf

cuboalga.stl

Minimalist cube shaped candle holder.
Algae version.



Lil Astro Puzzle // Mini Astrolabicon

LilAstro.stl

citycube | candle holder

citycube.stl

CREATEK S-111 | 3D Printable Storage Box (STL)

View all files in the CREATEK series, setting recommendations, and more: https://bit.ly/createk3d

This model is work licensed under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. To view a copy of this license, visit: http://creativecommons.org/licenses/by-nc-sa/4.0/

Cube

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

ClickCube - Clicker Flushie Cube, Ludo fidget

KWOB Puzzle // Ziggy A

5x5 Puzzle Cube

XYZ Calibration Test - Vase Mode

Planetary Gear Cube Fidget Toy by Ruven Bals

Print-in-Place Geared Rising Box

Twisty Cube Puzzle

cuboalga.stl

Lil Astro Puzzle // Mini Astrolabicon

citycube | candle holder

CREATEK S-111 | 3D Printable Storage Box (STL)

Auxetic Cubes // 18mm 2x2

Force Field Puzzle 2x2 Cube

Auxetic Rectangles // 18x32mm 5x3 Stacked Diagonals

Cuboid Slide Fidget

Triple Twist Cube (Stochastic)

Mario Question mark box bank

Auxetic Cubes // 30mm 3x3

Dual Hexahedron Fractal

Gear Cube Lamp Ceiling