Infinity clip

infinity_clip.stl

A clip

a_clip.stl

Safety clip (Clip de racor)

It is a safety clip for the pneumatic fitting or for a 4mm outer diameter quick connector for 3D printer.

The G-code is created with PrusaSlicer for Prusa mini with an ultra definition of 0.05 mm; but it can also be printed for Creatity and other printers that use Marlin, (if you have a glass bed with clamps, make sure before putting it on, to remove the front clamp on the left, to prevent the nozzle from colliding with it, when doing the first line of filament checking), since PrusaSlicer does it on the front of the hot bed, not like Cura, which does it on the left.

 

Il s'agit d'un clip de sécurité pour le raccord pneumatique ou pour un connecteur rapide de 4 mm de diamètre extérieur pour imprimante 3D. 

Le code G est créé avec PrusaSlicer pour Prusa mini avec une ultra définition de 0,05 mm ; mais il peut également imprimer pour Creatity et d'autres imprimantes qui utilisent Marlin, (si vous avez un lit en verre avec des pinces, assurez-vous avant de le mettre en place, que vous retirez la pince avant gauche, pour éviter que la buse n'entre en collision avec (lors de la vérification de la première rangée de filaments), puisque PrusaSlicer le fait sur le devant du lit chaud, pas comme Cura, qui le fait sur la gauche.

 

Se trata de un clip de seguridad para el racor neumático o para un conector rápido de 4 mm de diámetro exterior para impresora 3D. 

El código G está creado con PrusaSlicer para Prusa mini con una ultra definición de 0,05 mm; pero también se puede imprimir para Creatity y otras impresoras que usan Marlin, (si tienes una cama de cristal con abrazaderas, asegúrate antes de ponerla, de quitar la abrazadera frontal de la izquierda, para evitar que la boquilla choque con ella, al hacer la primera línea de comprobación de filamento), ya que PrusaSlicer lo hace en la parte frontal de la cama caliente, no como Cura, que lo hace en la izquierda.

Clips_Light_Heavy v1.stl

Needed these for hanging things on the wall, good for "chip clips" and lots of other things. 

light strip clips MK3 Ender3 version

I made this for my own light strip that i ordered from amazon.
Light clips sit between the top bolts

link is for those wanting it, its NOT an affiliate link.

https://amzn.eu/d/3mR5AXP

light strip clips MK3 (open ended)

Figure 8 Compliant Clips

figure8-long.stl

Compliant Stand Clips

standclipwide.stl

HMG7 Longer LK5 Pro Gantry Adapter.stl

This STL is a component of the Hero Me Gen7 Printhead assembly for 3D printers.

**Hero Me Gen7 is a modular printhead platform for 3D printers with excellent part cooling and the most compatibility across printers, hotends, extruders, ABLs, and other components.**

 The Hero Me Gen7 is all about choice and personal preference. If you have been upgrading your 3D printer, you've made choices about what is important to you, Your choices are likely going to be different from everyone else. When choosing a hotend, extruder, and ABL combo (not to mention fans and accelerometers), where are you going to find a printhead platform that will accommodate all your selected components (which could be a rare combo), for your specific 3D printer AND provides part cooling that gives you great print results. **This is what the Hero Me Gen7 is all about!**

Think of the Hero Me platform as lego blocks for printheads, there are mounting parts for each component (hotend, extruder, fans, ABLs, etc.) that stack and mount to a core Base. Component specific mounting parts can be interchanged for another of the same type. So, should you change your component selection(s) in the future, you do not have to start over, you simple replace the single STL mount that is matched to the new component. There is no need to yet again go looking for a new set of mounting hardware that was not likely to have been designed to work with each other in the first place.

So to give you choice and fulfill your personal preferences in 3D printing, the Hero Me Gen7.3.2 now supports over 100 3D Printer models (plus clones), 46 Hotends, 34 Extruders (over 45 mount options), 17 ABL Sensors (34 mount options), 35 Part Cooling Duct options, 12 Cable Management options, 11 ADXL345 mounts, and 4 LED bar mounts (among many other options). Gen7.3.2 supports most of the popular 3D printers and components available. 

If you know your 3D printer model, hotend, fans, and optionally an extruder, ABL sensor, ADXL345 accelerometer (for Klipper), and any other options for your printhead assembly, you can scan through the Hero Me Gen7 Release 3.2 folder, or use the Thangs Advanced Search.  Be sure to set the creator filter to: ‘MediaMan3D’ then search for ‘HMG7’ which should bring up all the STLs. You can refine your search from there by component, brand, etc.

If you find that you have a 3D printer model or component that is not yet supported, send me information and preferably a STEP or STL (or link) if you know of one for the X carriage of that printer or the component and I will create a mount for it. Send to: MediaMan3D@gmail.com

If you want Hero Me documentation… The Hero Me Gen7.3.2 folder of STLs on Thangs is organized into sub-folders by component category, with sub—sub-folders for type and brand with well defined filenames to make it easy to find what you need. If you want documentation to help you select and assemble the Hero Me Gen7 for your specific 3D printer, you can get a membership plan here on Thangs.  You will get a detailed 56 page parts selection and illustrated assembly guide along with assembly videos, private Discord server access (with over 2,000 Hero Me users), technical support, and much more, You also get exclusive access to new STL releases 30 days before being posted to Thangs, and other STL libraries. Check out the membership plans here:  [https://thangs.com/designer/mediaman3d](https://thangs.com/designer/mediaman3d)

 Clip Chip to hold your chip clips 

The Clip Chip (for your chip clips), is a good tip to keep your clips (and your chips) from giving you the slip. The dips on the chip should ensure a non-slip grip on your chip clips. Don't flip if the dips along your chip don't form an even strip. This should be something you can whip up with a real zip, but I won't nip at any of your tips. The tip of the chip does dip enough to make it stable enough to ship, but don't flip if that goes to slip. Don't take my quips as some sort of superior drip; I will trip as much as I skip. Let me know what issues you have with you clip chip, and how it can better grip your chip clips.

blip, crip, gyp, kip, lip, rip, sip, thrip, yip.

Moon Clip holder for ammo can

This will hold up to 36 loaded moon clips for the most popular calibers.  The dowels print at 1/2 inch in diameter and are 5" tall.  Fits in 1/2 of a 50 cal ammo can or a plastic MTM can.  I used double sided gorilla glue tape to secure it to the bottom of the can.  16 hour print.  Long but worth it. Printed on a prusa mini with PLA   

CLIPS

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Infinity clip

A clip

Safety clip (Clip de racor)

Clips_Light_Heavy v1.stl

light strip clips MK3 Ender3 version

light strip clips MK3 (open ended)

View 111 new models

View 72 new models

View 510 new models

Clip Chip to hold your chip clips

Moon Clip holder for ammo can

Caution Hot Mounting clips

28mm Stone Wall Hclip Board Pack