Double Winged Kaleidoscope Christmas Ball

Double Winged Kaleidoscope Ball - One Piece.stl

Winged Kaleidoscope Christmas Ball

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems and diamond patterns.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 6.5 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height or even adding infill. Infill is counter-intuitive, but it means the hot end moves to a different part of the layer, giving the outside a chance to cool. 

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 mm
* Alternate Extra Layer: Yes

I had the best results using Cura setting the default width to 0.4 mm with an alternate extra wall. 

*Infill*
I would recommend adding 100% infill to the loop at the top of the ornament to make the loop stronger, but I wouldn't add infill anywhere else. It just adds weight.

To add infill (or extra walls, tops or bottoms) to just one area of an object in Cura:
1. Add a support blocker
2. Select the support blocker and scale and position it where you want the added infill
3. Select “Per Model Settings” then select “Modify Settings for Overlaps”
4. Select “Select Settings” and check “Infill Density” then select “Close”
5. Enter the amount of infill you want

*Speed*
* Outer Wall: 20 mm/sec
* Inner Wall: 20 mm/sec
* Top/Bottom Speed: 20 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
You will probably need supports for bed adhesion.

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 60 Degrees

I also added a custom cylindrical support to either side where the bottom ledges intersect. This not only helps with printing the point of intersection, it help prevent the model from wobbling or coming loose from the print plate.

Divided Tree Ornament

Closed Spiral Christmas Ornament

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I printed at 200 C with 115% flow.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 mm. 

*Infill*
This does not need any infill. JUST DON'T DO IT – especialy if you print it with transparent filament.

*Speed*
* Outer Wall: 20 mm/sec
* Top/Bottom Speed: 20 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
I first printed with used normal supports and an overhang angle of 67 degrees and no other supports. It worked until 2 minutes from completion, when the model came loose from the bed. When I tried again, I with an overhang angle of 64 degrees and added 8 custom supports that keep the model from wobbling. I've included a screenshot from Cura of the supports. 

I added a support blocker in the loop to keep from having supports added inside the loop.

Santa Hat for IKEA Gestalta

Super easy Santa hat for your IKEA GESTALTA! 

Very easy print, could be printed with filament swap or just colored. 

No Supports needed. Printed with PLA at 210° C on an Anycubic Vyper.

Grinch-worthy Planetary Snowman Hairify a remix

Planetary Snowman

Starburst Christmas Ornament

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems and diamond patterns.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4.5 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 105, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm with an alternate extra wall. 

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 49 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 mm above the build plate so that the supports would only be added to the bottom of the ornament.

Diamond Lattice Christmas Ball

Double Diamond Christmas Ball

###About the Design
This is a new variation on my Christmas Balls with Integrated Stems and diamond patterns.

###Not To Be Sold
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

###Resizing
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

###Print Time
About 4.5 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 105, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm with an alternate extra wall. 

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 49 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 mm above the build plate so that the supports would only be added to the bottom of the ornament.

Diamond Christmas Ball Design 2

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems. It may be a little challenging to print. The key is to get the speed, temperature and flow right for your particular printer/filament combo so the stem prints cleanly at the narrowest point.

I printed this in Matterhackers Translucent Red. It's a nice balance between translucency and reflectivity. For an opaque filament, I'd use a multi-color PLA (like Matterhackers Quantum) or a medium toned silky PLA (gold, red, just use anything that's not really light or dark). Either type of filament would show off the facets nicely.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 110, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm and adding custom settings for the base of the ball that printed it 0.8 mm thick. You can do this by adding a support blocker to the bottom and giving it custom settings of 0.4 mm. Cura adds the two and prints the area within the blocker at 0.8 mm.

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I really relied on the supports for build plate adhesion. I used a brim, but I set it to 3.2 mm gap from the print so it would touch the supports but not the ornament.

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
Support Overhang Angle: 45 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 m above the build plate so that the supports would only be added to the bottom of the ornament.

Stocking Hook

Just a simple mantle hook for hanging stockings that I designed shortly before Christmas. Tested with up to 25lbs of weight. Easy print, no supports; I used PETG, 3 walls and 30% infill. Enjoy!

Fhw_ @Build_over_Bot edit (Blitzen) h left.stl

Hello Tribe,

Another of my eight tiny robot reindeer.

Cheers
Maker Millwright

Acorn - Screw It Yourself

exploded_view_DO_NOT_PRINT.stl

2023 glasses

Glasses to celebrate the new year, be the coolest of New Year's Eve. 

They are printed directly (they need support in the joint above the nose) and their assembly is very simple.

With a 1,75mm filament, you cut a piece and insert it between the sidepieces of the glasses and the support of the glasses and then you can use a spot heat or glue to fix it on the sides.

Santa Claus Sleigh Christmas Tree Decoration

This is a plain Christmas Tree Ball with the Santa Claus Sleigh silhuette and some different snowflakes designs.
It's designed to be printed in different colors to achieve the final result, if you want you can print it in one color and paint later.
This is the filament color change configuration if you print with 0.2mm layer using Cura "Pause at Height":
0 to layer 15 (0 to 3mm) = Red
16 to 19 (3.2 to 3.8mm) = White

ALL Frikarte3D designs are protected by the Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or print models of my designs without my explicit written consent.

To sell them legally, message me so we can work out a deal.

Hope you like it! Any advice, or recommendation is welcome! Happy Printing!

I would be very grateful if you print it and put it on social networks to tag me at [@Frikarte3D](https://www.instagram.com/frikarte3d/)

Santa Claus Sleigh Christmas Tree Decoration 🎅🛷🎄

John McClane Christmas Tree Decoration

This is a John McClane (Bruce Willis) from Die Hard Christmas Tree Decoration. 
Die Hard is an action movie from the 90's and is considered as a Christmas Movie, then what's better to have that iconical character in your Christmas Tree?

It's designed to be printed in different color changes to achieve the final result, if you want you can print it in one color and paint later.
This is the filament color change configuration if you print with 0.2mm layer with Cura Slicer:
0 to layer 13 (0 to 2.6mm) = Light Skin
14 to 17 (2.8 to 3.4mm) = Black
18 to 21 (3.6 to 4.2mm) = White
22 to 25 (4.4 to 5mm) = Red

ALL Frikarte3D designs are protected by the Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or print models of my designs without my explicit written consent.

To sell them legally, message me so we can work out a deal.

Hope you like it! Any advice, or recommendation is welcome! Happy Printing!

I would be very grateful if you print it and put it on social networks to tag me at [@Frikarte3D](https://www.instagram.com/frikarte3d/)

Hairify Remix of Frosty The Snowman

DISPLAY ONLY REMIXFROSTY.stl

Diamond Christmas Ball

After creating a bell with this pattern (see Diamond Christmas Bell, I wanted to see what it would look like as a ball. I loved it, so I had to share it with you. It printed easily for me with just a little support. It looks great with multi-color PLA, but it'll also look great in solid colored PLA (opaque or transparent).

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

***PRINT SETTINGS***
* Walls: 0.4 - 0.8 mm (I made the walls of the ball 2 lines thick and the walls of the stem 1 line thick).
* Layer Thickness: 0.15 mm recommended. Anything from 0.1 - 0.2 mm should look good.
* Infill: None. Seriously. It doesn't need it. It just adds weight and print time.
* Rafts/Brim: I didn't use either. 
* Supports: I added normal supports with an overhang angle of 56 degrees. It holds the ball to the printing plate and supports the extreme overhangs at the base without adding a lot of time to the print.

FHW: 2022 Modern Christmas Ornament ornament Ball 3

hello Tribe,
I think this is number 21 of this years ornaments.

Cheers
Maker Millwright

Snowman finger up

Remix of Estalactitas de hielo multi holder

Estalactitas de hielo decorativas.

Impresas sin relleno ni soportes.

Puedes añadirles luz led si lo deseas.

CHRISTMAS

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Double Winged Kaleidoscope Christmas Ball

Winged Kaleidoscope Christmas Ball

View 40 new models

Closed Spiral Christmas Ornament

Santa Hat for IKEA Gestalta

Grinch-worthy Planetary Snowman Hairify a remix

Starburst Christmas Ornament

Double Diamond Christmas Ball

Diamond Christmas Ball Design 2

Stocking Hook

View 13 new models

Acorn - Screw It Yourself

2023 glasses

Santa Claus Sleigh Christmas Tree Decoration

John McClane Christmas Tree Decoration

Hairify Remix of Frosty The Snowman

Diamond Christmas Ball

View 15 new models

Snowman finger up

Remix of Estalactitas de hielo multi holder