These are the roof pieces for the Magnetic Tile Haunted House. 

****3D Print Settings****
PLA Filament works great
Layer height 0.2mm
Infill 15%
No supports need 
****Neodymium magnets needed for all Roof Pieces (except chimney): 20x5x2 and 10x5x2****
****Neodymium magnets needed for chimney: 10x5x2 OR 12x5x3****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for these prints: https://www.amazon.com/shop/3dpmom
 
****How to Print Roof Pieces****
For the roof pieces , you will need to use 20x5x2 and 10x5x2 neodymium magnets only.  I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers. 

For all of these pieces, add a pause print to insert the magnets as shown in the photos for each design. When the print is paused insert the magnets.    

For the Roof Corner Piece, Roof Dormer Piece,  Roof Deep Dormer Piece and Roof Panel Pieces you will need to ****pause the print twice****: the first pause will be at layer height 7.8mm; the second pause print will be at 87.2mm. 

****Note:**** For the second set of magnets to be inserted at the 87.2mm height you will need to to place a magnet on the outside of the print to hold the ‘inside’ magnet in place. (Otherwise the magnet may ‘jump out’ and stick to the print head.)  

After the magnets are inserted/secured, resume the print. When you are done with the print simply remove the magnets off from the outside of the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Roof Corner Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #2 (Roof Dormer Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #3 (Roof Deep Dormer Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #4 (Roof Panel Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #5 (150x75 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #6 (75x75 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #7 (75x37.5 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #8 (Chimney): one color, pause inserted at layer 30 (layer height 6.0mm)

Have fun printing!

Magnetic Tile Haunted House: ROOF

Roof Corner Piece.stl

I recently released my ‘Mega’ Magnetic Tile Haunted House Collection but have been wanting to make a playful, scaled down version - so here it is 👻 This is my ‘Mini’ Magnetic Tile Haunted House that is ¼ the scale of my original. For extra fun, many of the windows have 2-sided window panes that rotate, there's a skeleton that greets you behind a hinged front door, tombstones to decorate the front yard and all the spiders, cats, rats, ghosts and skeletons you can handle 🕷🎃🐈‍⬛🐀👻 (These tiles are compatible with store bought magnetic tiles just fyi:)

****3D Print Settings****
PLA Filament
Layer height 0.2mm (for some of the more detailed pieces - like the rat windows and tombstones you can use a 0.16 layer height if preferred)
Infill 15%
Brim may be needed on larger pieces (like the 150x75 walls) if you notice any warping

****Neodymium magnets needed: 20x5x2 ****

- I specifically designed all these pieces to work with this size magnet

- Here is a link to these magnets on Amazon: ****https://amzn.to/3Nibhd3****

- Magnetic build plate highly recommended but not absolutely necessary.


****Printing Instructions for Inserting Magnets and Filament Pieces:****

- Every piece in this collection (except for the Porch Pillars and the Chimney Cap) need to be paused at layer 30 (layer height 4.8mm) to insert magnets. 
- The Front Door piece and all the window panes that rotate also need cut pieces of filament placed in the ‘filament chamber’ areas (see photos and video). 
- It helps to straighten the filament pieces that will be inserted into these pieces.  I have designed a separate 3D printed device to do that (I call it the ‘filament straightening block’) and will link a video below.

- After the magnets/filament are inserted, resume printing

****I have also included a 3mf print profile with the following print plates:****
Print Plate #1 Mini HH_75X75_Front Door: 4 colors, pause at layer 30, cut and insert filament pieces to fit into filament chamber areas
Print Plate #2 Mini HH_75x75_Curved Cat & Ghost Window: 4 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #3 Mini HH_75x75_Curved Spider & Ghost Window: 4 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #4 Mini HH_75x75_Curved (Plain) Window: 3 colors, pause at layer 30
Print Plate #5 Mini HH_75x75_Rectangle Spider & Ghost Window: 4 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #6 Mini HH_75x75_Rectangle Pumpkin & Ghost Window: ****5 colors!!****, pause at layer 30. Cut and insert filament pieces to fit into filament chamber areas.
This is the only piece with 5 colors. You will notice I colorized both the ghost and the pumpkin white.  After the white is done printing the ghost you will need to change out the white filament for orange before it starts printing the pumpkin.  Pause the print if needed to do this (on my Bambu printer I can do this while printing).
Print Plate #7 Mini HH_75x75_Rectangle (Plain) Window: 3 colors, pause at layer 30
Print Plate #8 Mini HH_75x37.5_Curved (Plain) Window: 3 colors, pause at layer 30
Print Plate #9 Mini HH_75x37.5_Curved Rat Window:3 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #10 Mini HH_75x37.5_Plain Wall Panel: 1 color, pause at layer 30
Print Plate #11 Mini HH_150x75_Curved Skeleton & Ghost Window: 4 colors, pause at layer 30; cut and insert filament pieces to fit into filament chamber areas
Print Plate #12 Mini HH_150x75_Curved (Plain) Window: 3 colors, pause at layer 30
Print Plate #13 Mini HH_150x75_Tree Wall: 2 colors, pause at layer 30
Print Plate #14 Mini HH_75x75_Floor Piece: 1 color, pause at layer 30
Print Plate #15 Mini HH_75x37.5_Floor Piece: 1 color, pause at layer 30
Print Plate #16a Mini HH Front Porch: 1 color, pause at layer 30
Print Plate #16b Mini HH Porch Pillars: 1 color, pause at layer 30
Print Plate #17a Mini HH Tombstone Noah&RIP: 2 colors, pause at layer 30
Print Plate #17b Mini HH Tombstone Ben&Waldo: 2 colors, pause at layer 30
Print Plate #18 Mini HH Front Door Awning: 1 color, pause at layer 30
Print Plate #19 Mini HH_75x85_roof: 1 color, pause at layer 30
Print Plate #20 Mini HH_90x85_roof (no chimney): 1 color, pause at layer 30
Print Plate #21a Mini HH_90x85_roof with chimney: 1 color, pause at layer 30
Print Plate #21b Mini HH Chimney Cap: 1 color, pause at layer 30

Have fun printing!

Mini Magnetic Tile Haunted House Collection

(21a) Mini HH_90x85_roof with chimney.stl

These are the door/door wall surround pieces for the magnetic tile haunted house. 

PLA Filament works great
Layer height 0.2mm
Infill 15%
Brims recommended for front door wall and french door wall  to prevent warping on the corners
****Neodymium magnets needed: 20x5x2, 10x5x2 and 3x5****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for these pieces: https://www.amazon.com/shop/3dpmom

****3D Print Settings****
For the wall pieces,  you will need 20x5x2 and 10x5x2 neodymium magnets to be inserted around the edges. I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.  
I like to alternate these two size magnets between the magnet holes (20x5x2, 10x5x2, 20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak.I recommend 20x5x2 neodymium magnets to be used for the door pieces.

For the 150x150 Large Front Door Wall and 150x150 French Door Wall pieces there is a small circular space for one magnet centered above each arch. Insert a 3x5 neodymium sized magnet into that space.

For the doors, I recommend 20x5x2 neodymium magnets.

For all of these pieces, add a pause print to insert the magnets as shown in the photos for each design. When the print is paused insert the magnets. After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Front Door Wall): one color, pause inserted at layer 30 (layer height 6.0mm), brim added
Print Plate #2 (Front Door): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #3 (French Door Wall): one color, pause inserted at layer 30 (layer height 6.0mm), brim added
Print Plate #4 (L& R French Doors): one color, pause inserted at layer 30 (layer height 6.0mm)

Have fun printing!

Magnetic Tiles Haunted House: DOORS

150x150 Front Door Wall.stl

These are the light base and light shade pieces for the magnetic tile haunted house. 

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15%
No brims or supports needed
****Neodymium magnet size needed: 7x2 ****
****Small light needed (see link below)****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the light and magnets that fit into this print. 
https://www.amazon.com/shop/3dpmom

I designed these to be used with 7x2 neodymium magnets. I strongly recommend using this size magnet. These magnets do not have space to rotate. This piece, as well as the window boards, are the only pieces designed this way BUT all the other magnets in my designs rotate so they will orient to the magnets in these pieces.

For the light base, add a pause print at layer height 13.6mm to insert the magnet. When the print is paused insert the magnet.  After the magnet is inserted, resume the print.
For the light shade, begin the print with yellow (or whatever color you choose). Add a pause for filament color change at 0.6mm. After filament change is complete, resume print.  

****How to assemble the porch light****
When the light shade is done printing, fold along seams and slide flaps together so they lock together on the inside of the shade.  Slide the shade into base, add a light and you're done:) 

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Porch Light Base): one color, pause inserted at layer 95 (layer height 13.6mm)
Print Plate #2 (Porch Light Shade): two colors

Have fun printing!

Magnetic Tiles Haunted House (PORCH LIGHT)

Porch Light Base.stl

These are the window board pieces for the magnetic tile haunted house. 

I designed these to be used with 6x2 neodymium magnets.  I strongly recommend using these size magnets. When inserted into the print, these magnets do not have space within their 'chambers' to rotate. These window board pieces (as well as the light base piece) are the only pieces designed this way BUT all the other magnets in my designs rotate so they will orient to the magnets in these pieces.

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15%
No brims or supports needed
****Neodymium magnets needed: 6x2****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the light and magnets that fit into this print. That's it:)
https://www.amazon.com/shop/3dpmom

For these window boards, add a pause print at layer height 2.8mm to insert the magnets. When the print is paused insert the magnets.  After the magnets are inserted, resume the print.

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Window Boards 1-3): one color, pause inserted at layer 14 (layer height 2.8mm)
Print Plate #2 (X-Shaped Window Boards 1-3): one color, pause inserted at layer 14 (layer height 2.8mm)

Have fun printing!

Magnetic Tile Haunted House WINDOW BOARDS

X Window Board_1.stl

These are the railing, pillar, arch and beam pieces for the magnetic tile haunted house. 

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15-20%
No supports needed (see recommendations for brims below)

****Neodymium magnets needed for arches and railings: 20x5x2 and 10x5x2****
****Neodymium magnet size need for pillars: 12x5x3 OR 10x5x2****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for this print:
https://www.amazon.com/shop/3dpmom

****Arches****
Neodymium magnets sizes needed for the arches: 20x5x2 and 10x5x2 (I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.)
I recommend brims for the arches to prevent warping at edges.
For the arches, add a pause print at layer height 6.0mm to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak.
After the magnets are inserted, resume the print.

****Railings****
Neodymium magnet size need for railings: 20x5x2 and 10x5x2
Brims are not needed for the railings.
Add a pause print at layer height 6.0mm to insert the magnets.  I like 20x5x2 for the magnets at the bottom of the railing and 10x5x2 for the magnets along the side of left and right railings. Insert magnets, then resume print.

****Pillars****
I recommend a brim for the pillar body/base piece because it is tall.  The brim will help add stability. 
Add a pause print at layer height 6.0 mm to insert the magnets. Insert magnets, then resume print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Railing Pieces): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #2 (Pillar Pieces): one color, pause inserted at layer 30 (layer height 6.0mm), brim added to base/body piece
Print Plate #3 (150x150 Arch Wall): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #4 (150x150 Arch Wall with Notch): one color, pause inserted at layer 30 (layer height 6.0mm) 
Print Plate #5 (Beam Piece): one color

Have fun printing!

Magnetic Tile Haunted House RAILINGS, PILLARS, ARCHES & BEAMS

Right Porch Railing.stl

If you're looking for a fun Halloween 3D printing project - look no further 👻 These are the wall pieces for a magnetic tile haunted house. 

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15%
Brim recommended on 150x150 wall pieces to prevent warping
****Neodymium magnets needed: 20x5x2, 10x5x2 and 3x5****
I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.
Magnetic build plate highly recommended but not absolutely necessary.

For all these pieces, add a pause print at layer 29 (layer height 5.8 mm) to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak. (See videos) 
The 3x5 magnet is used only in the Double Window Wall and Single Window Wall above the windows.

After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (150x150 Double Window Wall): one color, pause inserted at layer 29 (layer height 5.8mm), brim added
Print Plate #2 (150x150 Porthole Window Wall): one color, pause inserted at layer 29 (layer height 5.8mm), brim added
Print Plate #3 (150x150 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm), brim added
Print Plate #4 (150x75 Single Window Wall): one color, pause inserted at layer 29 (layer height 5.8mm)
Print Plate #5 (150x75 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm)
Print Plate #6 (150x37.5 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm)
Print Plate #7 (75x75 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm)
Print Plate #8 (75x37.5 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm)

Here is a link to Amazon for the magnets needed for these pieces.
https://www.amazon.com/shop/3dpmom

Have fun printing!

Magnetic Tile Haunted House: WALLS

 150x150 Wall.stl

If you're looking for a fun Halloween 3D printing project - look no further 👻 These are the floor and/or flat roof pieces for a magnetic tile haunted house. 

3D Print Settings
PLA Filament
Layer height 0.2mm
Infill 15%
Brim recommended on 150x150 floor pieces to prevent warping
****Neodymium magnets needed: 20x5x2 and 10x5x2****
I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers. 
Magnetic build plate highly recommended but not absolutely necessary.

For all of these pieces, add a pause print at layer 30 (layer height 6.0mm) to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak. (See videos)

After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (150x150 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #2(150x150 floor w/ center magnets): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #3(150x75 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #4(75x75 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #5(37.5x75): one color, pause inserted at layer 30 (layer height 6.0mm)

Here is a link to Amazon for the magnets needed for these pieces.
https://www.amazon.com/shop/3dpmom

Have fun printing!

BUILDING BLOCKS

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Magnetic Tile Haunted House: ROOF

Mini Magnetic Tile Haunted House Collection