PERSPEKTIVA 3 Tier Bowl // 

PERSPEKTIVA_3-Tier-Bowl.stl

PERSPEKTIVA Square Dish // 140x140x50mm

PERSPEKTIVA_SquareDish_140x140x50.stl

Caliper Coaster Set - Angled.stl

V4 Caliper Coaster Set.stl

PERSPEKTIVA Small Dish // 85x115x35mm

PERSPEKTIVA_SmallDish_85x115x35.stl

PERSPEKTIVA Cube Bowl // 120x120x120mm

PERSPEKTIVA_CubeBowl_120x120x120.stl

PERSPEKTIVA Small Square Dish // 115x115x35mm

PERSPEKTIVA_SmallSquareDish_115x115x35.stl

75mm PERSPEKTIVA Cube

PERSPEKTIVA_Cube_75mm.stl

OP-1 BestCase Decksaver and Stand // Waveform (multipass multicolor)

e-case.stl

OP-1 BestCase Decksaver and Stand // Wicker

Protect your OP-1 in the coolest way possible with a _decked out cases!_ The OP-1 BestCase is both a deck protector and a stand that tilts the OP-1 up to take advantage of the same ergonomic benefits that computer keyboards have been rocking since the 80's.

---

To get the 2 color graphics, swap filament at 0.4mm layer height. This can be achieved with pause at layer height plugins for Cura, Octoprint, etc, or by slicing two separate models, one that stops at 0.4mm and the next starting at 0.4mm. Some printers have a built in pause at layer height feature.

The model includes round tabs at each corner to improve build plate adhesion. They can be ripped off afterward, or cleanly removed with a X-acto knife.

As you're likely aware, PLA is not sun-friendly, so avoid exposing a PLA case to warm environments to prevent warping. If you want extra security, I recommend silicone bands like these [Grifiti Bands](https://amzn.to/2Vs8Cn7) (also on [eBay](https://ebay.us/WTUA4B)) or [these](https://amzn.to/2KlG1JT).

 

OP-1 BestCase Decksaver and Stand // Wide Awake [Red Eye Series] 

Protect your OP-1 in the coolest way possible with a _decked out cases!_ The OP-1 BestCase is both a deck protector and a stand that tilts the OP-1 up to take advantage of the same ergonomic benefits that computer keyboards have been rocking since the 80's.

This design comes from my Red Eye Series, which consists of 3 original art pieces inspired by sleepless nights spent searching for inner peace while making tunes.

---

To get the 2 color graphics, swap filament at 0.4mm layer height. This can be achieved with pause at layer height plugins for Cura, Octoprint, etc, or by slicing two separate models, one that stops at 0.4mm and the next starting at 0.4mm. Some printers have a built in pause at layer height feature.

The model includes round tabs at each corner to improve build plate adhesion. They can be ripped off afterward, or cleanly removed with a X-acto knife.

As you're likely aware, PLA is not sun-friendly, so avoid exposing a PLA case to warm environments to prevent warping. If you want extra security, I recommend silicone bands like these [Grifiti Bands](https://amzn.to/2Vs8Cn7) (also on [eBay](https://ebay.us/WTUA4B)) or [these](https://amzn.to/2KlG1JT).

 

Angled

Most Popular Paid of All Time

Categories

Paid

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

PERSPEKTIVA 3 Tier Bowl //

PERSPEKTIVA Square Dish // 140x140x50mm

Caliper Coaster Set - Angled.stl

PERSPEKTIVA Small Dish // 85x115x35mm

PERSPEKTIVA Cube Bowl // 120x120x120mm

PERSPEKTIVA Small Square Dish // 115x115x35mm

75mm PERSPEKTIVA Cube

OP-1 BestCase Decksaver and Stand // Waveform (multipass multicolor)

OP-1 BestCase Decksaver and Stand // Wicker

OP-1 BestCase Decksaver and Stand // Wide Awake [Red Eye Series]