Mini Christmas Dragon Keychain

MiniMonster#1SANTAhatKeychain.stl

Gyro Tree - Peek a Meow

catinchristmastree.stl

Christmas Tree Desktop Ornament

Tree2022-Tree.stl

Solid Christmas Tree Slices with Star! ⭐

4.5 Inch Solid Christmas Tree with Star.3mf

Cat christmas tree decoration v2.stl

Hang it in Your christmas tree or somewhere else.

Diamond Christmas Ball Design 2

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems. It may be a little challenging to print. The key is to get the speed, temperature and flow right for your particular printer/filament combo so the stem prints cleanly at the narrowest point.

I printed this in Matterhackers Translucent Red. It's a nice balance between translucency and reflectivity. For an opaque filament, I'd use a multi-color PLA (like Matterhackers Quantum) or a medium toned silky PLA (gold, red, just use anything that's not really light or dark). Either type of filament would show off the facets nicely.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 110, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm and adding custom settings for the base of the ball that printed it 0.8 mm thick. You can do this by adding a support blocker to the bottom and giving it custom settings of 0.4 mm. Cura adds the two and prints the area within the blocker at 0.8 mm.

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I really relied on the supports for build plate adhesion. I used a brim, but I set it to 3.2 mm gap from the print so it would touch the supports but not the ornament.

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
Support Overhang Angle: 45 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 m above the build plate so that the supports would only be added to the bottom of the ornament.

Santa Baby Yoda Christmas Decoration

This a remix of the [Baby Yoda Christmas Tree Decoration No Circle](https://thangs.com/designer/frikarte3D/3d-model/Baby%20Yoda%20Christmas%20Tree%20Decoration%20No%20Circle-551142?manualModelView=true).
In that version I changed the clothes to be able to print white the suit in white and red to become a Santa Claus suit.
It's designed to be printed in different color changes to achieve the final result, if you want you can print it in one color and paint later.
This is the filament color change configuration if you print with 0.2mm layer using Cura with "Pause at Height":
0 to layer 5 (0 to 1mm) = Red
6 to 9 (1.2 to 1.8mm) = Green
10 to 13 (2 to 2.6mm) = Black
14 to 17 (2.8 to 3.4mm) = White

ALL Frikarte3D designs are protected by the Copyright Law. By downloading, YOU HAVE NO RIGHT to sell any digital files or print models of my designs without my explicit written consent.

To sell them legally, message me so we can work out a deal.

Hope you like it! Any advice, or recommendation is welcome! Happy Printing!

I would be very grateful if you print it and put it on social networks to tag me at [@Frikarte3D](https://www.instagram.com/frikarte3d/)

,christmas

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Mini Christmas Dragon Keychain

Gyro Tree - Peek a Meow

Christmas Tree Desktop Ornament

Solid Christmas Tree Slices with Star! ⭐

Cat christmas tree decoration v2.stl

Diamond Christmas Ball Design 2

Santa Baby Yoda Christmas Decoration

Remix of Frosty The Snowman REMIX CONTEST

FOLD STAR | FOLDABLE CHRISTMAS DECORATION

Shelf Grinch

Cozee -The Baby Dragon

Star for Lil Nic 2021

Christmas Box for Festive Aesthetic

Lantern Christmas Bulb 2024

Santa Jack Ornament

Mistletoe - Cookie Cutter with Stamp

Light Up House For Tealights and Fairy Lights Multiparts

2D Christmas Star

Spiral Christmas Tree Topper 2024

Candy Knot - Tritangentless