Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5147664.

Desk Stand for your GoPro or Action Camera.  I used a M4 x 30 bolt to fasten the attachments to the base.  I used a 1/4 20 nut, bolt and wing nut for the attachment that lets you use your gopro or action camera as a screw on.

The base for this stand the one for my web cam stand are interchangeable. https://www.thingiverse.com/thing:5153141

GoPro Desk Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3899131.

I wanted to daisy chain 2 wyze cams using the wyze camera wall mount bracket on amazon but when I tried to close the wall mount with the  2 usb cables attached there wasn't enough room in the wall mount to allow that to happen.  I ended up cutting off the nub on the back of the mount with a hacksaw blade and this left a hole that left room for the cables.  I didn't want to leave this hole so I created a simple round cover and crazy glued it to the back and this allows the cables to fit nicely.

Wyze Cam Wall Mount Mod

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4626401.

(See v2 here https://www.thingiverse.com/thing:4816068

Got tired of my fishing rods getting tangled up in the back seat of my truck.  Tried some of the other clips from Thingiverse but all my rods had different dimensions so I designed these clips to be more or less universal.

These are easy to modify.  Just load them into Tinkercad and adjust them to suit.  Print them in the orientation as loaded.  You shouldn't need support for the "A" (Female) part.  I tried them with and without and they printed fine without.

I printed them in both PLA and Petg.  If you're going to leave in your car in hot weather Petg would probably be the better choice but they print so fast it's not a problem to print spares.

I think these clips might be useful for other things and if you find another use for them please let us all know.

The clips named "Alt"  are the clips without a middle bar.


Fishing Rod Clips

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3667604.

Needed some way to protect my GoPro Hero while traveling, so created this box.  The add on's aren't really required but the two pins help hold the camera from moving about in the box. The GoPro logo and the two pins were glued in place with CA glue. I glued a piece of felt to the inside of the lid.  I use an elastic to hold the lid on although it fits fairly tight.

I may make some modifications to the design but I needed something quick.  

GoPro Travel Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5153159.

A Desk Web Cam holder to put webcam at eye height.  This was made for my Logitech C525 but will probably fit many others.  There is a small arm and a large arm.  You'll only need the one that suits you best.  You'll need 1 M4 x30 and 1 M4 x20.  The desk stand is from my GoPro Desk Stand.  https://www.thingiverse.com/zzalrs/designs

Web Cam Desk Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4127296.

I did this just for something to do and I'm not sure if it could be useful to anyone.  I suppose you could use the corner mouldings if you didn't have a mitre saw.  There's an inner and outer corner as well as a straight piece....You could make a photo frame out of it.

Quarter Round Mouldings

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5153141.

A web cam desk stand to hold web cam at eye level.  Made for my Logitech C525 but will probably fit many others.  Two arms, long one is 88mm and short one is 62mm so choose one or the other.  You'll need 1 M4 bolt x30 and 1 M4 bolt x20.  The stand  is from my GoPro Desk Stand.  https://www.thingiverse.com/thing:5147664

Logitech C525 Web Cam Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4977601.

This is a spool holder that lets you keep the door on your FlashForge Adventurer 3 without making any modifications to the machine for printing external filament.

All of the other designs are hours and hours, tons of wasted plastic and you have to keep the door off. 

Prints in 39 minutes. Super minimal design.... did I mention you can keep your door on?

I would like to add two little tiny filament guides for running the filament through the inside that can handle just raw filament or to hold a PTFE tube permanently. 

So little time! 

I hope you guys enjoy this. 

I printed this with PLA Carbon Fiber and included the gcode (.gx) and flashforge project (.fpp)


Headrest holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4816068.

This is an improvement from my previous rod holders (https://www.thingiverse.com/thing:4626401)   
I wouldn't print these in PLA specially if you were going to leave them in your car for any length of time.
I used 100% infill but I'm sure anything above 20 would work as well.


I usually have at least 3 rods on the floor in the back seat and they always managed to somehow get entangled with each other.  This new version does a much better job of  preventing it.

Rod Holder v2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3882380.

added a pad and crazy glued the holders to it

added a pad

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5136058.

A cover for my power supply.

Fan Grill

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5324395.

Just a knob.

Knob

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3236427.

This is a nut made basically for cigar box ukuleles. It's 38mm long and has small notches for the strings.  The strings will be 11mm apart.  

Ukulele Nut 38mm

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3236456.

Lens cover for Logitech C525 but probably fit others.

C525 camera lens cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5339613.

A stand to hold the Ozempic pen.

Ozempic Pen Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4123270.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/czzm2nKaQB5

 GoPro Hero+ battery holder (3 batteries)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4644741.

This is remix of jasondb1's "Scotty Rod Holder Arm design "  I used his design to create a gopro mount that attaches to a Scotty Rod Holder extension for my kayak.
https://www.thingiverse.com/thing:3838711

Scotty Gopro mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4929568.

Slip garbage bag into slot ( I use doggie poop bags)  Turn holder sideways and insert it between the fins on your vent twist it to lock in place.  I used PETG because of the heat in the car....don't know if PLA would hold up.

Car vent garbage bag holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3340389.

Thanks to Waverunner62 for an awesome design.  I wanted to be able to add my gopro to his design so I adapted one of his arms to accept a 1/4 20 bolt.  This will let you add any camera as long as it's not too heavy .

Camera End

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4121899.

A battery holder for GoPro Hero+ batteries (3 batteries)

GoPro Hero+ battery holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4977663.

A headrest holder for the rear headrests on a Honda Ridgeline.  Probably fit other models.  The front hole is 15mm and the back is 14mm.   I designed this to give me better visibility out the back window..

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3340366.

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/fRLOmvjxuDj

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4639767.

Lost the speed control knob for my Homelite leaf blower so made a new one.  Printed in Petg and 100% infill and used an m3 to screw tighten it. (might not be needed)

Homelite leaf blower knob

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5147664.

Desk Stand for your GoPro or Action Camera.  I used a M4 x 30 bolt to fasten the attachments to the base.  I used a 1/4 20 nut, bolt and wing nut for the attachment that lets you use your gopro or action camera as a screw on.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

zzalrs

Achievements

Seedling

Debutant

GoPro Desk Stand

Wyze Cam Wall Mount Mod

Fishing Rod Clips

GoPro Travel Case

Web Cam Desk Stand

Quarter Round Mouldings

Logitech C525 Web Cam Stand

Headrest holder

Rod Holder v2

added a pad

Fan Grill

Knob

Ukulele Nut 38mm

C525 camera lens cover

Ozempic Pen Holder

GoPro Hero+ battery holder (3 batteries)

Scotty Gopro mount

Car vent garbage bag holder

Camera End

GoPro Hero+ battery holder

Headrest holder

Camera End

Homelite leaf blower knob

Rod Holder v2

GoPro Travel Case

Fishing Rod Clips

GoPro Desk Stand

GoPro Hero+ battery holder (3 batteries)

C525 camera lens cover

Headrest holder

Scotty Gopro mount

Wyze Cam Wall Mount Mod

Fan Grill

Camera End

Homelite leaf blower knob

GoPro Hero+ battery holder

Car vent garbage bag holder

Web Cam Desk Stand

Logitech C525 Web Cam Stand

Quarter Round Mouldings

Headrest holder

added a pad

Camera End

Ukulele Nut 38mm