Boring zippers no more! Grab a slice! It's chessylicious!

**Items you need:**
- 2 x “4mm x 30cm” paracord.
- *4 x “3mm (diameter) x 2mm (thick)” magnets (neodymium magnets are recommended for better holding power).
- Super glue (for the magnets).

*If you do not have magnets, I have included a [3D-printed Connector](https://thangs.com/designer/zipperrific/3d-model/Zipper%20Pull%20-%20Connector-1123107).

**Suggested print settings:**
- Layer height 0.2mm.
- Infill 30%.
- Position the print in a way that the joining face is facing downwards.
- No supports are needed.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Zipper Pull - Cheese

cheese-R-zipperrific.stl

Boring zippers no more! Expanding the Zipper Pull collection - tempting but do not dunk this one. 🛑🥛😆

Items you need:
- 2 x “4mm x 30cm” paracord.
- *4 x “3mm (diameter) x 2mm (thick)” magnets (neodymium magnets are recommended for better holding power). 

*If you do not have magnets, I have included a [3D-printed Connector](https://thangs.com/designer/zipperrific/3d-model/Zipper%20Pull%20-%20Connector-1123107).

**Suggested print settings for the Main Body - Cream:**
- Layer height 0.2mm.
- Infill 30%.
- Position the print in a way that the joining face is facing downwards.
- No supports needed.
 

**Suggested print settings for Biscuit:**
- Layer height 0.2mm.
- Infill 15%.
- Position the print in a way that the joining face is facing downwards.
- No supports needed.
 

**ASSEMBLY**
Align the notch and cavity for the "biscuit" and affix in position using glue. Verify that the text is correctly positioned.


_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Zipper Pull - Oreo

oreo-biscuit-L-zipperrific.stl

Boring zippers no more! Expanding the Zipper Pull collection - let's welcome good fortune!

**Items you need:**
- 2 x “4mm x 30cm” paracord.
- *4 x “3mm (diameter) x 2mm (thick)” magnets (neodymium magnets are recommended for better holding power).

*If you do not have magnets, I have included a [3D-printed Connector](https://thangs.com/designer/zipperrific/3d-model/Zipper%20Pull%20-%20Connector-1123107).

**Suggested print settings:**
- Layer height 0.2mm.
- Infill 30%.
- Position the print in a way that the joining face is facing downwards.
- No supports are needed.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Zipper Pull - "Good Fortune" Chinese Coin

chinesecoin-R-zipperrific.stl

Boring zippers no more! Ghost from Pac Man!

**Items you need:**
- 2 x “4mm x 30cm” paracord.
- *4 x “3mm (diameter) x 2mm (thick)” magnets (neodymium magnets are recommended for better holding power).
- *2 x “12mm” wiggly eyes.
- Super glue (for the eyes and magnets).

*If you do not have magnets, I have included a [3D-printed Connector](https://thangs.com/designer/zipperrific/3d-model/Zipper%20Pull%20-%20Connector-1123107).

**Suggested print settings:**
- Layer height 0.2mm.
- Infill 30%.
- Position the print in a way that the joining face is facing downwards.
- No supports are needed.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Zipper Pull - Ghost (Pac Man)

pacghost-R-v2-zipperrific.stl

Connector for the Zipperrific's zipper pull collection.

Suggested print settings:
- Layer height 0.2mm.
- Infill 50%.
- Perimeters: 5.
- Refer to the image for print orientation.
- No supports needed.

ASSEMBLY
Choose which side (Zipper Pull) you'd like the connector piece to stay, and insert the longer end all the way in. Slight force may be needed.

NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise.

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Zipper Pull - Connector

connector-thewhatbrandsg.stl

Boring zippers no more! Expanding the Zipper Pull collection - a low poly piece. 💓

**Items you need:**
- 2 x “4mm x 30cm” paracord.
- *4 x “3mm (diameter) x 2mm (thick)” magnets (neodymium magnets are recommended for better holding power).

*If you do not have magnets, I have included a [3D-printed Connector](https://thangs.com/designer/zipperrific/3d-model/Zipper%20Pull%20-%20Connector-1123107).

**Suggested print settings:**
- Layer height 0.2mm.
- Infill 30%.
- Position the print in a way that the joining face is facing downwards.
- No supports are needed.
- Suggest using glossy filament for a beautiful reflective finish.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Zipper Pull - Low Poly Heart

heart-lowpoly-R-thewhatbrandsg.stl

Boring zippers no more! Expanding the Zipper Pull collection - this one is for all dog lovers! 🐶🦴

**Items you need:**
- 2 x “4mm x 30cm” paracord.
- 4 x “3mm (diameter) x 2mm (thick)” magnets (neodymium magnets are recommended for better holding power).
 
**Suggested print settings:**
- Layer height 0.2mm.
- Infill 30%.
- Position the print in a way that the joining face is facing downwards.
- No supports are needed.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Zipper Pull - Bone

bone-L-thewhatbrandsg.stl

Boring zippers no more! Expanding the Zipper Pull collection - which colour is your favourite? 🔴🟠🟢🔵⚫

**Items you need:**
- 2 x “4mm x 30cm” paracord.
- *4 x “3mm (diameter) x 2mm (thick)” magnets (neodymium magnets are recommended for better holding power).
- Super glue (for M text and magnets).

*If you do not have magnets, I have included a [3D-printed Connector](https://thangs.com/designer/zipperrific/3d-model/Zipper%20Pull%20-%20Connector-1123107).

 
**Suggested print settings for the Main Body:**
- Layer height 0.2mm.
- Infill 30%.
- Position the print in a way that the joining face is facing downwards.
- Supports are needed around the overhang of the “M Text” area (refer to image).
 

**Suggested print settings for M Text:**
- Layer height 0.2mm.
- Infill 15%.
- Position the print in a way that the front (the side that is showing ) side is facing downwards.
- No supports needed.
 

**ASSEMBLY**
Position the text with the smoother side (the side on the print bed) facing outward. Confirm that the text is correctly positioned and secure it in place with glue.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Zipper Pull - M&M

mm-R-thewhatbrandsg.stl

Boring zippers no more! Don't get spooked by this one! 💀

**Items you need:**
- 2 x “4mm x 30cm” paracord.
- *4 x “3mm (diameter) x 2mm (thick)” magnets (neodymium magnets are recommended for better holding power).
- 2 x “12mm” wiggly eyes.
- Super glue (for the eyes, mouth and magnets).

*If you do not have magnets, I have included a [3D-printed Connector](https://thangs.com/designer/zipperrific/3d-model/Zipper%20Pull%20-%20Connector-1123107).


**Suggested print settings for the Main Body:**
- Layer height 0.2mm.
- Infill 30%.
- Position the print in a way that the joining face is facing downwards.
- No supports are needed.
 

**Suggested print settings for Mouth:**
- Layer height 0.2mm.
- Infill 15%.
- Brim: Width 2mm (optional).
-- Brim Separation Gap: 0.2mm.
- Position the print in a way that the chamfered side is facing upwards.
- No supports are needed.

**ASSEMBLY**
Affix the mouth to the main body with the chamfered side facing downwards.

_NOTE
Most of our designs are printed and tested on a Prusa Mini and MK4, so tolerances may vary if you are using a different brand. While we strive for a smooth experience with our designs, we appreciate your understanding if tolerance issues arise._

This work is licensed under a
Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike

Zipper Pull - Skull Face

skull-L-thewhatbrandsg.stl

skull-mouth-thewhatbrandsg.stl

skull-R-thewhatbrandsg.stl

bone-R-chipped-thewhatbrandsg.stl

pacghost-L-v2-zipperrific.stl

cheese-L-zipperrific.stl

Adding a touch of personality to your zippers. From cute and quirky designs to sleek and sophisticated styles, we've got something to suit every taste and personality.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

zipperrific

Achievements

Seedling

Debutant

Pinned models

Zipper Pull - Skull Face

Zipper Pull - Bone

Zipper Pull - Ghost (Pac Man)

Zipper Pull - Cheese

Zipper Pull - Cheese

Zipper Pull - Oreo

Zipper Pull - "Good Fortune" Chinese Coin

Zipper Pull - Ghost (Pac Man)

Zipper Pull - Connector

Zipper Pull - Low Poly Heart

Zipper Pull - Bone

Zipper Pull - M&M

Zipper Pull - Skull Face