for ryobi track guide 6.5inches wall mount (print 2), uses M4 nut and bolt, very tight fit on nut and bolt gently hammer the nuts in and the bolt will ensure a tight fit.

how to print:
handle : print flat 
mount : print on its thinner side, use supports if u wish (recommended on the top portion (of the mount piece) that touches the bed where it curves, however supports ARE NOT needed and will print as is but will look slightly weird lol

how to use:
1. first twist bolt all the way til the bottom is flush with the back side,
2. then mount to wall
3. slide track saw into place and then twist the cap til it holds the track
4.profit

ryobi guide wall mount.stl

top piece ryobi guide.stl

video of my print with these files -  https://youtu.be/quvNsO3Y03Y
**edit: notes : i have remodeled the "default files" it should print nicely now, sorry for any inconveniences**
i made this in onshape, can be found on there searching for "azureusflames".
Masterball - this one snaps close, hinge has a 3.3mm hole, it is about 56mm wide in diameter, looks really close to the real thing. 
The model comes with different parts so it requires assembly and additional things not included ( glue of choice, i used Loctite superglue and a pin for the hinge, i used "uxcell 50Pcs 3mm x 18mm Dowel Pin 304 Stainless Steel Shelf Pegs Support Shelves Silver Tone" from amazon)
i have other balls in the making that reuse all the model files except the top half.
* "reusable"  = reusable with my other models so don't need to redownload if you already have
 
this one comes in 2 different ball styles, one with a raised "M" no body imprint  ( calling this one "alternate" and one that sits almost if not flush with the ball "default", the image displays a default print

files required to make the ball
1. bottom half  (reusable)
2. top ring (reusable)
3. bottom ring (reusable)
4. button (reusable)
5. Left and Right pink sides
6. pick DEFAULT or ALTERNATE
- default M
- default Top half
- Alternate M
- Alternate Top half



Masterball

master top half extrude.stl

i made this in onshape, can be found on there searching for "azureusflames"
another pokeball only this one snaps close, hinge has a 3.3mm hole, it is about 56mm wide in diameter, looks really close to the real thing, the model comes with different parts so it requires assembly and additional things not included ( glue of choice, i used Loctite superglue,  and a pin for the hinge, i used "uxcell 50Pcs 3mm x 18mm Dowel Pin 304 Stainless Steel Shelf Pegs Support Shelves Silver Tone" from amazon)
*"reusable"  = reusable with my other models so don't need to redownload if you already have

i have other balls in the making, that reuse all the model files except the top half
files required to make the ball
1. pokeball top
2. bottom half  (reusable)
3. top ring (reusable)
4. bottom ring (reusable)
5. button (reusable)


Pokeball with hinge and snap

pokeball top half.stl

just a simple device that has 1mm to 10mm holes sizes and rectangle cube for visualization
made with onshape, search same name for easier remix

visual measurement device.stl

Leave a comment for a request, no guarantees though, simple request will be way more likely to be done.

 Leave a comment for a request, no guarantees though, simple request will be way more likely to be done.

Request here

next is luxury ball (requested) unfortunately this will require a whole new body D:

 next is luxury ball (requested) unfortunately this will require a whole new body D:

xazurewindx

Achievements

Seedling

Novice Maker

Designer posts

Request here

working on

Pinned models

Pokeball with hinge and snap

Masterball

ryobi guide wall mount.stl

Masterball

Pokeball with hinge and snap

visual measurement device.stl