The **Lenovo P350** case is slightly different than the other Lenovo Tinys I've been using, and I had to model this one from scratch. It won't, for example, work on a M720q without modification.

The screw holes are threaded, and you can reuse the original screws with PLA. On a Creality CR6-SE at 0.28mm, it's not perfect, but it is good enough. With a small effort and a hand driver, the screws will self-tap the rest of the way, and torque to a reasonably snug level. You'd probably have to run a tap or have a high resolution print for anything tougher than that, though. Or just drill out and use your own hardware, as is the case with most of these types of brackets.

I printed with the arms that mount to the adapter in the up position, with supports.

If you remix, please share alike.

Lenovo P350 Tiny PCIe Bracket (Baffle) for Mellanox CX353A ConnectX-3 QDR InfiniBand + 10GigE Adapter.stl

Remixed simbaja's Lenovo Tiny PCI-E Bracket to work with a Mellanox CX311A 10gb adapter. I'm using it on a ThinkCentre M920x, but should fit most Tiny's in that generation.

Lenovo Tiny PCIe Bracket for Mellanox CX311A

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4911663.

I want to automatically power my RPi up and down automatically with the CR-6's power switch. To that end, I'm getting power from a spare 24V rail off the CR-6's PSU, using a LM2596 step-down module to output 5V, and a UPS hat with a small battery that triggers a graceful shutdown of the RPi when power is cut.

Malolo's case was a fantastic starting point, but I wanted it mounted out of the way on the v-rails. I also liked the PiCam mount from https://www.thingiverse.com/thing:4650151, and the photo shows that being used as well.

All I did was raise the standoffs in the top to accommodate the UPS hat, add v-slot mounts, and lastly a mounting point for the camera mast. You can print the standoffs or just use any standard 12mm RPi hat standoffs.

Print the top using bed supports for the v-rail mounts. No supports needed for anything else.

Creality CR-6 SE RPi 4b+Hat V-Mount Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4912530.

To keep cables running from the top of the Z-axis down to the bottom tidy and out of the way. The top clip is help with friction, whereas the bottom clip requires replacing the two factory M3 screws with longer ones (I used M3x10mm with washers).

Creality CR-6 SE Z-Axis Cable Clips

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4917769.

Mount for "Comidox 5PCS WS2812 5050 RGB 8 LEDs Light Strip Driver Board 8 Channel Built-in Full Color-Driven Development Board Black for Arduino" I got from [Amazon](https://smile.amazon.com/gp/product/B07KD55QKJ/) that measure 57mm x 10.5mm each.

V2 is for three LED modules soldered back to back. You'll need to print the bracket at a 45-degree angle to fit into the CR-6 SE bed. Mount the bracket to the bottom of the upper Y-tail with T-nuts and M3x6mm screws, then M3x4mm screws to mount the LED modules into the bracket. If a diffuser is desired, I printed the one in the picture with white PLA. I recommend it, those lights are pretty bright.

The following applies only to the V1 version:

You could omit the snap-in part if you want to use t-nuts instead, and you don't need supports if you print it that way. Otherwise you definitely need build plate supports.

CR-6 SE LEDs Top Y-Rail Mount for WS2812 5050 RGB 8 Light Strip 

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

ubt

Achievements

Seedling

Lenovo P350 Tiny PCIe Bracket (Baffle) for Mellanox CX353A ConnectX-3 QDR InfiniBand + 10GigE Adapter.stl

Lenovo Tiny PCIe Bracket for Mellanox CX311A

Creality CR-6 SE RPi 4b+Hat V-Mount Case

Creality CR-6 SE Z-Axis Cable Clips

CR-6 SE LEDs Top Y-Rail Mount for WS2812 5050 RGB 8 Light Strip