I really liked this design but it didn't fit the hair ties I already had, so I shortened the hair tie paths to fit them better. The hair tie paths are also cleaned up to remove an overhang in the middle. I added a chamfer to the top and bottom for ease of printing and to improve the feel of it in your hand.

I've also made a bunch of variants, some inspired buy the original author's designs and some of my own. My personal favorites are the Hex Border ones, so check them out!

STEP File of all models is also available

**INSTRUCTIONS:**
Print two of which ever design you like, the model is the same for both sides. The two sides attach together with two hair ties, following the paths

Remix of [TopLoader Wallet](https://www.printables.com/model/702993-toploader-wallet-hair-tie-wallet)

**Licence:**
This work is licensed under a
[Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike](https://creativecommons.org/licenses/by-nc-sa/4.0/)


TopLoader Wallet - Smaller Hair Tie & Chamfer

toploader-hex.stl

Plastic piece of a microphone stand that attaches the boom arm to the stand itself 

Microphone stand arm clamp 

MicStand_Arm_Clamp%20v2.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4880797.

A foldable chess set, designed to store all your peices as well.

The tiles on the board are 25x25mm and each half of the board is 25mm heigh (26.5mm including clips/feet. The entire board measures 200x200 when folded out.

Peices are from https://www.thingiverse.com/thing:470700 but scaled down so the bases are about 20mm in diameter

Parts
-------

There are 4 different parts to print, and you should have 6 parts total when all printed, they are:
- 1x Top Shell
- 1x Bottom Shell
- 2x Board Tile Halves
- 2x Hinges

You will also need:
- Foam (To hold the peices in place) - I used https://www.bunnings.com.au/kincrome-custom-cut-foam_p0131564
- Two Part Epoxy 
- Super glue
- Craft kinfe


Printing:
-----------

Top & Bottom Shells: Print with their top face down on the bed of the printer. I printed with 2 bottom layers, 2 walls and 20% infil. Best to print these one at a time as they are quite large, you may need to disable skirts/brims/rafts depending on the size of your buildplate.

Board Tile Halves: This was split off as a seperate piece so the tiles could be printed facing up to prevent warping. Print with 100% infil as this is designed to be 1.4mm tall (7 layers at 0.2mm). Same as the shells, you should only print one at a time and may need to disable skirts/brims/rafts depending on your buildplate.

Hinge: Credit to https://www.thingiverse.com/thing:2187167. I modified this model to create the slim hinge for this box. Print flat side down with no supports and 20% infil. Clearence between moving parts is about 0.4mm which is more than enough to prevent the halves welding together. It might need a little force to get it moving initially so be carful not to snap the joints. if you are finding you cant move the hinge try printing at 80% speed, and with the part cooling fan at 100% (if you have one). Or try Cura's Enable Bridge Settings.

Assembly & Finishing
-----------------------------

Glue the tiles onto the shells using epoxy, I used 5min epoxy but its still best to let this dry for a few hours to a day before doing any of the finishing steps. 

If you want to paint this, its easier to sand and paint the board before gluing the hinges on here is a good guide on painting 3D prints. https://all3dp.com/2/beginner-s-guide-to-painting-3d-prints-pla-abs/

Cut the foam to fit inside each half of the shells. Trace the outline of the peices onto the foam and cut them out. Once thats all done and the peices fit you can glue the foam into each half of the shell using epoxy.

Glue the hinges into the cutouts on one half using super glue, ensuring the barel of the hinge is facing outwards. Once that has dried glue the hinges to the other half of the board.

You should now be able to fold the board in half and it should just click together, if you find the fit is a bit tight you can sand down the tabs that fit the two halves together, or trim them off with side cutters.




Chess Board Hinged Box

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

subnebula

Achievements

Seedling

Explorer

TopLoader Wallet - Smaller Hair Tie & Chamfer

Microphone stand arm clamp

Chess Board Hinged Box