Cable guide for brake and speedo cable that bolts to existing holes in the lower yoke.

Morini 2c cable bracket bolts to bottom yoke

cable bracket.stl

Print in TPU for Grimeca disc brake caliper. Bleed nipple cover.

nipple cover. for Grimeca Caliper

nipple cover.stl

Print in TPU for a Morini gear change rubber. Increase infil % to make stiffer.

gear change rubber.stl

Print in PLA. Clamps to frame tube to hold a 'Japanese' style rear stop switch. Comes in 2 halves, use M6 screw and nut to clamp to frame and switch.

Bracket for Japanese style rear stop switch

stop bracket v2.stl

You may need to adjust the scale to get a better fit.  Print in TPU and experiment with infil to get the desired elasticity.

brake caliper bleed nipple cover.stl

1 off. Print in TPU and experiment with infil to get the desired elasticity.

Moto Morini 250 2c gear change rubber.stl

One of the rubber gaskets used to hold the rear light onto the number plate holder. Print in TPU and experiment with infil to get the desired elasticity.

Moto Morini rear light outside assembly.stl

rear light front outside assembly.stl

Moto Morini rear light inside assembly v2.stl

rear light front inside assembly v2.stl

Close model dimensions taken from actual example. 4 needed. Print in TPU, experiment with infill to get similar elasticity. I have used Recreus 82A TPU with 2mm walls and 50% infill.

Moto Morini tank support rubbers

tank front rubber v3 measured off actual.stl

Moulds that can be used as press moulds to reproduce the number plate holder from mild steel.  Registration holes in the corners to keep parts aligned. I squashed mine in a large vice to apply the pressing pressure.

Number plate holder press plates for Morini 250 2c Light/number plate holder

Number plate plate hammer mould v4.stl

Printable in TPU to replicate the bump stiop rubbers for a Moto Morini 250 2c centre stand.

Centre Stand Bump Stop rubbers

Not a perfect copy, close enough to use.  Needs painting, and fixing holes drilling.

Moto_Morini_Tank_Badge

Side panel badge for the Moto Morini 250 2c. Not an exact copy but close enough? Edges need trimming to fit

Moto Morini 250 2c side panel badge

Side panel badge for the Moto Morini 250 2c. Not an exact copy but close enough?

250 side panel badge v2 to size.stl

3D TPU printed grommet for the alternator wire from the engine side cover.

Moto Morini wiring grommet alternator cover

grommet.stl

Print in TPU, plug/cover to block air balance tube to delete balance pipe between carbs.

Moto Morini Dellorto bleed valve plug

Carburettor to airbox rubbers print in TPU. Join between carb and airbox rubber can be cut to size.

Moto morini 250 2c Airbox to carb rubber

Moto morini Rubbers to link carbs to airbox

Fit to airbox then to carb rubber, print in TPU. Join between carb and airbox rubber can be cut to size.

Moto Morini 250 2c Carb to airbox rubber

inlet airbox carb rubber with supports extended  v3 x115.stl

Print in TPU (shore 95a a little too hard). Small mounts x 2 for front engine mount. Large x4 for rear

Garelli_Rubber engine mounts for a Garelli

Rubber engine mounts for a Garelli engine

Smaller rubber mounts for Garelli engine. Print in TPU

Garelli_front engine mounts x2.stl

front engine mounts x2.stl

Garelli_rear engine mounts x4

rear engine mounts x4 v2022.stl

Print in TPU to make the bobbins that fit on the side panel upper pins on most Moto Morinis

Moto Morini side panel bobbin

side panel bobbin.stl

3D printable model of the cam/crank holding tool for Moto Morini v twins. Has a shorter handle than the original Morini tool due to my print bed restrictions. Based on a CAD model from:  https://hofmann-andi.de/MoriniWebsite/CAD-Daten.html

Moto Morini 3D cam tool.stl

3D cam tool.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

richard parker

Achievements

Seedling