Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4354201.



DIY détecteur de filament / DIY filament detector

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4862799.

This is a support Plug Jack Socket for 12V DC Female Male Power Connector Adapter.

Support Plug Jack Socket for 12V DC Female Male Power Connector Adapter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5155347.

This device combines a filament rounout sensor and a filament jam sensor. It is made of two Mini Limit Switch, SPDT Snap Roller Lever Arms connected together.
The first sensor for the runout is set to HIGH when filament is in, and to LOW when filament is out.
The second sensor for the jam is set to LOW when their is no jam, and to HIGH when the filament tangles and pushes on the lever.
For the wiring, the common pin (C) of both sensors are connected and related to the JST connector. The normally open (NO) pin of the jam sensor is connected to the normally close (NC) pin of the runout sensor, and to the JST connector.
On the gantry support needs to generate supports for the print. All other parts can be printed without supports.

Combined_Jam_and Runout_Sensor_Newest

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5169373.

This is a case for the Ender-3 Pro LCD display.
The first support was not strong enough. So I designed this improved version of the support.

Neige_Ender-3_Pro_LCD_Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5198236.

This is another minimalist design of LCD casing.

The main part and the mount may need supports for the print.

Another LCD Casing

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5165299.

This is an improved version of a device that combines a filament rounout sensor and a filament jam sensor. It is made of a Mini Limit Switch, SPDT Snap Roller Lever Arms connected together.
The is set to HIGH when filament is in, and to LOW when filament is out.
The wires are connected to the common pin (C) and the normally closed (NC) pin of the switch. 
All parts can be printed without supports.
Yu can see the mounting process here: https://youtu.be/ITnBaLDbLKY

Latest All In One Filament Jam and Runout Sensor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4359737.

This is my first try in Fusion 360.

Logo EvaShu

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4677022.


20 % infill 


3D Printer Squares

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5178722.

This is designed for the Ender-3 Pro.

https://youtu.be/S_tLH1NmqwE

2020_Ender-3_Pro_LCD_Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5201568.

Sliced with Cura 4.13.0, the top side laying flat on the bed.
I used tree supports.
After the print, a little sanding is needed to remove the remaining parts of the supports inside the cover.
No screw is needed. If it's too loose, some double-sided tape can help.

https://youtu.be/N_c1Y6v2ktk

Neige Ender-3 Pro Hotend Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4874861.

This a mount for the 7 inches rearview LED monitor.

7 inch Reariew LED Monitor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5144918.

This a device that combines a filament runout sensor and a filament jam sensor.
I'm using a 628ZZ bearing (8 x 24 x 8mm).

https://youtu.be/xQZ7yTXnofM

Combined Sensor - Filament Runout and Filament Jam

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5171103.

This is a minimalist drawer designed for the Ender-3 v2.

Ender-3 v2 Drawer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4359764.

This a new version of EvaShu.

Awa Sakho 2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5158978.

This is an improved version of a device that combines a filament rounout sensor and a filament jam sensor. It is made of two Mini Limit Switch, SPDT Snap Roller Lever Arms connected together.
The first sensor for the runout is set to HIGH when filament is in, and to LOW when filament is out.
The second sensor for the jam is set to LOW when their is no jam, and to HIGH when the filament tangles and pushes on the lever.
For the wiring, the common pin (C) of both sensors are connected and related to the JST connector. The normally open (NO) pin of the jam sensor is connected to the normally close (NC) pin of the runout sensor, and to the JST connector.
On the gantry support needs to generate supports for the print. All other parts can be printed without supports.

Improved_Version_Filament_Jam_and Runout_Sensor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4684917.

This the easiest way to change the position of the power supply unit on the Ender 3 Pro.
It requires less printing time and filament.
It's very easy to mount.

Video link: https://youtu.be/kRFgehnlZSI

Ender 3 Pro Easiest Power Supply Unit Position Change

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4828324.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed.  It is too wide for the other two positions.
I have created a smaller version to fit the right-front corner and the back-center.

A M3-.50 nut is required. 

.22LR  ammunition lifter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5137277.

This is a DIY filament sensor made with a push button and a bearing.
Video: https://youtu.be/4neRCoefmLo

Push Button Filament Sensor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4809693.

This an improved version of my auto power off system for my Ender-3 Pro and Ender-3 V2, using an Infra-Red sensor, an Arduino Nano, and a relay.

Ender-3 IR Sensor Lower Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4981191.

This is for my new auto-power off system using an ultrasonic sensor.

Ender-3_Pro_Auto_Power_Off_Ultrasonic_Sensor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4562675.

This a basic filament guide.

Neige Filament Guide 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4950090.

This design combines a Raspberry pi case and a Raspberry cam case, both mounted on the QR Code cover on the X gantry of the Eder-3.

Video available here: https://youtu.be/zxbOBsRZepQ

Raspberry_Pi_QRCover_Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4677212.



Ender 3 Pro Left Side LCD Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4364079.

These accessories are designed for a 3D printer cover.

Cover 3D Printer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4890636.

This is a replica of the Creality Ender spool holder. 

Nozzle Diameter: 0.40 mm
Extrusion multiplier 0.80 (Flow Rate: 80%)
Retraction Distance: 6.50 mm
Retraction Speed: 25.0 mm/s
Infill: 50%


Ender-3 Spool Holder Replica

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4942397.

Double filament rotating support.
It can take two rolls of filaments and can rotate on its axis 360 degrees.

----------------------------------------

Support rotatif double filament.
Il peut prendre deux rouleaux de filaments et peut pivoter sur son axe sur 360 degrés.



Support rotatif double filaments

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4610728.

With this kit,  I solved the issue of my filament spool that was always falling from its holder.
Printable parts available here:
https://www.thingiverse.com/thing:4610728

The .stl and .f3d files are available here:
https://naedioba.com/3D%20Printer%20Spool%20Stop/

You can watch the demo video here: https://youtu.be/bZkM2_4i0WY


3D Printer Spool Stop

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5201560.

The text has 0.4mm height. It is printing with no bed adhesion type (skirt, brim...).

I used extrude cut to cut the text on the face of the box with 0.4mm height. Then the box is printed on the text itself using 0.5mm Z-hop in Cura 4.13. There are no supports.

https://youtu.be/N_c1Y6v2ktk


Ender-3 Pro/V2 QR Code Cover

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

naedioba1

Achievements

Seedling

Trailblazer

Debutant