Remix from [MakeringProgress](https://makerworld.com/en/models/604736#profileId-527459)

This file is a Work in progress, I didn't notice that the latch groove is on the wrong side on my remix.

Making their OWH into a IWH. Also closed up the side design for printability, and removed the screw holes for comfort.
Tested with "replica" in public for conceal carry.
Printed with PETG, clasp grabs onto pants, hook grabs onto belt on gun draw.

Springfield XDM in waist holster

Springfield XDM IWH.3mf

Allows for a MP7 springer to receive MP5 AEG mags. (Because its what I have)

PETG or similar, 0.4mm nozzle, 0.2mm resolution, clean the long feed tube of the adapter after print, some material catching the BBs on the short tube is fine as long as they can be pushed through with little force (catching on the small tube will eliminate double feeding).

Simply take the mag release pin out, remove the body screws, pull back the cylinder, insert the adapter, and finally reassemble the gun.

If you were to remix this design simply credit me.

MP7 Spring to MP5 AEG Mag Adapter

MP7 Spring to MP5 AEG V1.3mf

A cover to protect your cylinder from dirt and grime.
Print and sand just enough for a snug fit such that it does not require glue to stay.
Check for cylinder clearance by pulling the bolt both with and with out cover. If the cylinder is rubbing sand a couple of mm off the inside wall of the cover.

Airsoft L96 Cylinder cover for MB04 bolt action sniper

Cylinder Cover.3mf

Found an awesome model from Snoopukairsoft (https://www.thingiverse.com/thing:3021721), and I decided to make a matching bottom.
Included in the download is my bottom with the Solidworks file for it (I no longer have Solidworks), and the bottom merged with the upper made by Snoopukairsoft.

Print front end down, butt end up, snug supports with no need for supports on the inside.

I may work on a new version in the far future but it will take a while because I need to rebuild it in Fusion360.

His license for his work is CC BY 4.0 DEED

Airsoft AK Beta front RIS

BETA RIS.3mf

Speed strip 9mm for DoubleTap defense derringer. Was a request from a relative. To be printed in TPU.

Speed Strip 9mm for DoubleTap Derringer

Speed Strip.3mf

I merged a shotgun shell holder and a picatinny rail to make this design remix. There are tow versions one with wedge that adds some resistance to the shell, and one with out.
This way made in 3DBuilder by cutting off the top of the rail, and subtracting and merging it with the shell holder.

Credit:
Shotgun shell holder made by Anticolette: https://www.thingiverse.com/thing:2952114
Picatinny Rail made by Fmascare: https://www.thingiverse.com/thing:3060697

Printing:
Print shell holder vertically (shell standing up), print the clamp piece laying down. Thick wall, some infill. 
Check original creators for their recommendations.

Legal:
The licenses are CC0 1.0 Deed for the shell holder, and CC BY 4.0 Deed for the rail. Act as if this new variant is CC BY 4.0 with credit to Anticolette, Mellonsmaps, and even if not required Fmascare.

Airsoft Picatinny Shotgun Shell Holder Remix

Picatinny Shotgun Shell Holder with wedge.3mf

A larger cylinder head to reduce the sound in the WELL bolt action sniper when firing. It actually works very well.

USE TPU or other soft material.

Print with 1 wall thickness, 1 top layer and 2 bottom layers. The picture listed was with 50% infill and it was way too much, use at most 20% infill with Gyroid or some other 3D infill. Use snug tree supports to hold up the edges, or some other minimal support. Random seam and variable layer Hight worked well for me, or else use the smallest layer height you can easily print. Finally add some glue when mounting to cylinder head, not too much and not super hard glue.

Cylinder head damper for WELL MB04 APS Bolt Action Airsoft Sniper Rifle

Cylinder head damper.3mf

A mount for a 0.83in/21mm flashlight, there is a Picatinny file and a M-Lock file. The two files are the same but the picatinny portion has been chopped off the mount.
Check out Lemo's P-90 M-Lock rail https://www.printables.com/model/747660
And check out Rumcajcz's M-Lock nut
https://www.printables.com/model/747660

M-Lock & Picatinny to flashlight 0.83in 21mm

M-Lock to flashlight 0.83in 21mm v8.3mf

Butt pad for airsoft sniper. Holes 0.16 inch diameters, 1.15 inches apart. I think its a WELL MB04 APS Bolt Action Airsoft Sniper Rifle. 
To be printed in two parts, the base plate in hard plastic and the top for TPU.

Sniper Butt Pad

ButtPad.3mf

Very intrusive modifications for the Airsoft Desert Eagle CM.121
Yes the images differ, emboss or extrude cut your own propaganda. I recommend fusion 360 or 3D builder.

The Why- My hands are too small for the Desert Eagle, so I made a grip to replace it. Mag bottoms to fit with the grip, grip nuts to add detail, a mag release for better reloads (PETG is too weak to it doesn't work well), and a muzzle device that fits the outside of the internal barrel and the inside of the upper for accuracy. 

The How- Remove the existing grip covers, cut down the front portion of the grip close to be flush with the mag, cut and sand until the new grip covers fit, attach the new grip covers and plastic weld them together and fill in the gaps, lastly sand until its comfortable. Replace the mag bottoms by unscrewing the bottom two screws on the magazine, you should be able to figure it out. For the muzzle device, shove it on don't break anything.

The results- 8/10 poor fitment, lots of work, solves the problem, truer irons, looks better.

Airsoft Desert Eagle CM.121 Grip, Muzzle, and Mag mod

Desert Eagle Grip v8.3mf

I was born in a Dublin street where the loyal drums do beat
And the loving English feet, they walked all over us
And every single night when me Da would come home tight,
He'd invite the neighbors out with this chorus

Easter Lily Badge

Easter Lily Badge.3mf

A shell for the cyma 900 round flash mag hi-cap.
The latch may need to be shaved down some, and pin holes may or may not be in the correct place.
I printed out an older version in 4 pieces and soldered them together. Put seam on random out side to give it a texture.

AK magazine shell airsoft for cyma 900 round flash mag hi-cap

AK mag v8.3mf

To be taped or tied to halter.
Glued horns to angled pads to mount horns to horse.
Be careful, horses know how to use weapons.

Horse Halter Headband

Headband2.obj

Big enough for 2 complete PCs in one case, absolute monstrosity, built for a school project. I did print it out but I never used it. The PSU caddies and HDD caddies were not finished, it was a group project (they didn't work on it).

2 complete ATX motherboards, and over 20 fans. 

Print and assemble like shown.

PC Super tower

SidePanel1111.SLDPRT

A modified reinforced airsoft trigger to be used in the DE HK USP airsoft gun.

HK USP double eagle airsoft trigger

Brit Trigger v1.4 v0 v1.3mf

Pistol rail to picatinny under + over for HK USP airsoft gun

HK USP airsoft Pistol to Picatinny v7.3mf

Pistol to Picatinny v7.3mf

A quick cover to be glued in place, has text "Pink Tax".

Pistol Hammer Cover for HK USP airsoft gun

Pistol Hammer v1.3mf

Because I can't find cases for my phone.
To be printed out of TPU with supports, with the back facing up.
I will likely not complete the project until by old case breaks.

BLU G93 Phone case, Work in Progress

G93 Phone case v7.3mf

Airsoft Pistol Trigger HK USP

To replace the buttstock on the CZ Mod M airsoft gun to fit Zeee 7.4 2000 mAh battery

CZ-61 Scorpion Battery Butt Stock

CZ Battery Butt v1.2.3mf

Pistol battery box picatinny for Zeee 7.4 2000 mAh lipo

Pistol battery box v5.3mf

K-Bar to be printed in TPU at different densities. 2 different crossguards available.

K-Bar

K-Bar v10.3mf

Extended mag used for CZ-61 Scorpion. I made this model years ago on my old printer. The model isn't great, has some fitment issues and need some modifications to work. I printed it in multiple pieces and molded together. 

CZ-61 HIcap mag

CZM mag v0.6 Textured.SLDPRT

CZM mag v0.6 Textured.STL

Part used to attach inner door part to frame on Mitsubishi Galant

Plastic door nipple

Door plasic nipple.SLDPRT

Extends the grip on thee scorpion mod m airsoft gun to allow for longer battery

Scorpion Mod M Grip Extender

CZ grip v1.0.STL

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

mellonsmaps

Achievements

Seedling

Explorer

Debutant