This is a prototype of the collar used to fit the NV addon to the scope.
I wanted to use this on more than one rifle without having to remove the collar or try and buy more.

The collar fits and locks into place and should hold the original inserts in place with a could of M3/M4 nuts and bolts

I also included a cover for the IR lamp, As I am using a separate IR light I wanted something to protect the built in unit.

Baseoptics nv90 collarr and IR Cover

nv coller.stl

This is  the mk3 version with a few changes following testing.

A quick and simple print that can be used to hold a playing card as a target.
The holes are set out in a way to accommodate both .177 and .22 shooters.
Following testing a sing M4 bolt was found to be enough to hold the card in place (in previous versions). This however now adds two outer holes to allow more secure fixing where required or for extra stability (when using .22 for instance.
Holes are to be threaded in using the bolts(use a small amount of silicone oil for the first time to help cut in the threads). These can then me mounted on a board or as needed

The insert in this version can be used to go between the card and the bolts. This should again help to secure it but also stop any bending of the cards when using a single bolt.

cutting the deck holder.stl

Tophat, slip washer and powerwasher set for the SMK / Westlake B2.
Tophat and slipwasher designed to allow a piston sleeve to be installed.

SMK Westlake B2 Tophat

B2 tophat.stl

Sleeved Silencer Insert.stl

A smaller (70mm) wheel for Vicoptic scopes and possibly others. This was also designed to sit slightly further out than the standard one as I had issues getting my reximex magazines in with the standard one.

Vicoptic small focus wheel.stl

Vector Veyron test side wheel.stl

Having just got myself one of these I was shocked to find it comes in a flimsy cardboard box. This was the solution.

The box will hold the the Chronograph as well as space for 3 spare AAA batteries and a small screwdriver for changing

FX Chronograph Case

FX Case Bottom.stl

FX Case top v2.stl

A Screw lit container that will hold the 2x multishot magazines and the single shot loader that come the the Reximex Pretensis.

Original container is based off
https://www.thingiverse.com/thing:612709

reximex pretensis magazibe holder.stl

Use a traditional photographic spirit level for levelling rifle and scope
Rings are held in place with M3 nuts and bolt

1 inch scope spirit level / hotshoe holder.stl

1 inch  scope spirit level holder.stl

After removing the barrel band there will be a gap between where the band used to be and can course the fill cover to push back further than it should. This simple spacer solves that problem.

Printed at .28 for speed
dependant on printer calibration this may need to either be sanded slightly on the inside or enlarged in the slicer by a few points of a % due to the tight fit

Gamo Coyote fill cover spacer.stl

Designed to help stop me knocking a whole tin of pellets all over the floor and figured someone else might like it

a 3x10mm round magnet is inserted during printing.

Magnetic bench rest pellet tin holder

Designed to help stop me knocking a whole tin of pellets all over the floor and figured someone else might like it

Designed to mount a KUSBA on the extruder of a Ender 5 S1.

Remixed from 
https://www.thingiverse.com/thing:5168515

kusba ender 5 s1.stl

I needed a bed level view of the printer and nothing seemed to fit what I needed, so here it is. This should work with most webcams / go-pro's.

Mine is attached using a gopro tripod adapter.

Printed without supports @0.3mm layer hight

ender5s1 webcam mount.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

illsley.mark

Achievements

Explorer

Seedling