Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:6116180.

Simple dog poop bag holder for 25mm dia x 60mm long poop bag rolls. Horizontal, with a screw cap and handle for attaching as needed.

Poop Bag Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5531601.

Filament clip that is slightly flexible and holds the filament by distorting itself and putting minimal stress on the filament itself.

Push the clip forwards/backwards to adjust the tightness.

Filament Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5531656.

The metal handle broke, so I created a replacement. Thought I would share.

I made this for outdoors to chose PETG for the material.

Spigot Handle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5892699.

Remix of these two models.
https://www.thingiverse.com/thing:934943
https://www.printables.com/model/188774-gargoyle

Printed this with Overture Rock PLA for added effect.

Dart Rack Gargoyle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5530379.

Toilet paper storage/holder made to accommodate wide rolls. It was made to replace the metal cage style rack seen in the first image.

Print a TP_Holder_Basde and a TP_Holder_Cap along with as many TP_Holder_Section as you will require for your needs. The sections thread onto the base and each other to make this easily adjustable.

Images show a unit made with 4 printed sections, which will hold 4 rolls of toilet paper.

Suggested to print in orientation shown.

Toilet Paper Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5531675.

Another take on a toothpaste squeezer. Made to fit some of the larger tubes or tubes without flat ends.

Stand on end before printing.

Toothpaste Squeezer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5530539.

Created to be used as a GPU anti-sag bracket. Thread together, slide under the GPU, adjust up/down as needed.

Adjustable Pillar GPU support

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5530519.

Done as a for fun project to have a 100% 3d printed filament spool. Worked much better than expected so decided to share.

Print two bearings and one each of the other parts. Fits on the stock Ender 3 V2 filament spool bracket.

0.20mm or smaller layer height suggested for bearings and threaded parts, the others can be larger layer height if desired.

Orient parts on bed prior to printing.

When assembling, leave some play when installing the retaining nut (smooth one for the end) or the spool will not easily rotate when. Mounting nut (hex nut) should be tight.



Ender 3 V2 Filament Spool 100% 3d Printed

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5530356.

I designed this UFO in order to give this Alien a proper ship. https://www.thingiverse.com/thing:2668660


IMPORTANT: You must print both halves of the hull (Hull_1 and Hull_2) otherwise the threads will not be correct. The two halves are not a mirror image of each other. It was split in half to make printing easier and so as to not require supports.

ALSO IMPORTANT: If you want to add the Alien bust, it must be done prior to gluing the hull halves together otherwise you will not be able to fit his shoulders through the cockpit opening.

Hull_2 and Beamer will need to be rotated in your slicer (flat side down) prior to printing.

The UFO hull was printed from silk silver PLA.
The beamer (bottom half with the vertical glow sticks) was printed in black PLA.
The Alien bust was printed with deep blue glow in the dark PLA and plain black PLA for the eyes.

The STL files are redesigned a little bit from the original print shown in the photos. Mainly, I removed the dowel holes that were intended to help with gluing. I realized that two hull halves could be supported instead by setting them on top of a roll of duct tape (second image). They were glued together with clear E600 glue. The Alien bust can also be glued in.

I also increased the diameter of the rings on the underside to be able to accommodate two 8.00 inch long glow sticks comfortably.

I also devised some clips to enable hanging this which I would be happy to adjust for the current design and post if there is interest.

Alien UFO

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5530550.

Simple phone stand for the desk. Has openings to allow charging cord to be attached while mounted.

Orient on the edge (phone stand will be on its side) prior to printing.

Phone Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5973918.

Simple clip for mounting 10mm wide LED strips to the frame of a printer enclosure. Clips to 8mm dia frame rods.

LED Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5972435.

I remixed this to make a version that was cut out on the inside to allow for light to show through for a glow effect.

The cut out is sized for a mini teat light (30mm dia x 25mm high) but could be re-scaled for different size lights.

Recommend to use 20% or more infill to help block the light in the areas where it is not intended to shine through. That seemed to work well with black filament, lighter colors may need more.

I currently do not have any wood filament, but I would really like to see how that would look. Once I get through one of my other spools of filament I will have the capacity to pick a wood one up.

The right eye is much dimmer in real life, not sure why the photo came out that way.

Valheim Ward Light

https://www.printables.com/social/371218-ecm1974/prints

https://www.thingiverse.com/ecm1974/designs

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

ecm1974

Achievements

Seedling

Debutant

Explorer