Inspired by the now defunct link in " Seth's Bike Hacks" / "Berm Peak" video about 3D printed bike parts and tools, this is a simple tool to check the alignment of the handlebars on your bike. Hold it against the bars, sight through the gap to see if the front tire is centered. If you are really worried about precision, use a rubber band to attach a laser pointer to this. Works with bars of all common diameters, and stems up to 60mm wide. Prints without supports.

Bicycle Handlebar Alignment Tool for MTB, Road bikes

bar-alignment-tool.stl

Made this to watch movies on my phone during flights. Works at least on WestJet 737 and Q400 planes, in economy and business class seats, even if seat in front is reclined. Probably fits most plane seats that have the little extra pocket for the safety briefing cards, idk. 
Print two of them to hold your phone.

The through-hole is 4mm, and can be used with a long bolt or a 3d printed pin, to hold the two pieces, see photos. Its not really necessary though.

Airplane seat-back phone- and tablet holder

phoneholder.stl

I always found the clutch pedal in my tacoma to be really weird - all the engagement/disengagement happens on the first third of the travel, but the pedal has another 10cm+ to go before it hits the floor (and the clutch pedal sensor switch). At first I thought the previous owner had somehow worn out the clutch already, then I found out that this is apparently just how they are, for some reason. 

This part is a little experiment that slips over the tab on the side of the clutch pedal. It stops the pedal from travelling further, and also activates the clutch sensor switch so you can still start the engine etc. I didn't really measure it, but by feel it cuts off about one third of the useless pedal travel at the bottom. At least one mine, the clutch is more than fully disengaged by this point (definitely test this on your vehicle! Every clutch may be a little different). 

Makes the pedal work more like it does on every other manual vehicle i've ever driven.

This part is a bit rough and a "first version" but it works well as is, so I never bothered to refine it.
Secures with a M6 screw or grub screw.

Clutch Stop (pedal travel reducer) for Toyota Tacoma 3rd Gen

I always found the clutch pedal in my tacoma to be really weird - all the engagement/disengagement happens on the first third of the travel, but the pedal has another 10cm+ to go before it hits the floor (and the clutch pedal sensor switch). At first I thought the previous owner had somehow worn out the clutch already, then I found out that this is apparently just how they are, for some reason. 

This part is a little experiment that slips over the tab on the side of the clutch pedal. It stops the pedal from travelling further, and also activates the clutch sensor switch so you can still start the engine etc. I didn't really measure it, but by feel it cuts off about one third of the useless pedal travel at the bottom. At least one mine, the clutch is more than fully disengaged by this point (definitely test this on your vehicle! Every clutch may be a little different). 

Makes the pedal work more like it does on every other manual vehicle i've ever driven.

Secures with a M6 screw or grub screw.

Attaches to the top of the dashboard of any 3rd gen Toyota Tacoma. 17mm diameter ball to fit various phone mounts etc, I'm using it for a wireless magnetic charger that originally clipped onto the vent.

Best printed on its side with support under the ball. Use PETG or some other heat resistant material.

Accessory mount for Toyota Tacoma dashboard 17mm ball

Attaches to the top of the dashboard of any 3rd gen Toyota Tacoma. 17mm diameter ball to fit various phone mounts etc, I'm using it for a wireless magnetic charger that originally clipped onto the vent.

When you put a third generation (2015-2023) Toyota Tacoma in reverse at night, the backup camera shows... not much, because the license plate lights are angled up and shine straight into the camera lens, causing glare and weird exposure issues. 

These simple little plates attach with some double sided tape, and block the glare from the lights. This greatly improves the view in the backup camera while still allowing the license plate to be illuminated. 

You need to print two, and preferably print them in some UV stable material so they last longer outdoors.


Edit: New version is two millimeters longer to better block glare especially on right side.

Toyota Tacoma glare blocker for better backup camera view (license plate lights)

When you put a third generation (2015-2023) Toyota Tacoma in reverse at night, the backup camera shows... not much, because the license plate lights are angled up and shine straight into the camera lens, causing glare and weird exposure issues. 

These simple little plates attach with some double sided tape, and block the glare from the lights. This greatly improves the view in the backup camera while still allowing the license plate to be illuminated. 

You need to print two, and preferably print them in some UV stable material so they last longer outdoors.

This is somewhat specific but maybe useful for someone else? 
My S22 phone is in a clear silicone case (width 75.5mm, thickness 11mm), and I use a round wireless charging pad thats about 90mm diameter and 10mm thick. I made this wall mount, that holds the wireless charger in the correct position so it charges the phone when I slide it in. 

Wall mount for Samsung S22 with wireless charger

Holder for a TOPDON TC001 infrared camera from amazon. The camera itself is designed to attach on the bottom of a USB-C smartphone, but I find it more useful when held separately with the included cable, so I made this gopro compatible holder for it. The camera fits snug in this case, but should probably be secured with a rubber band if used upside down. 

Printed upright in PLA. May need a tiny bit of support under the radius of the go pro mount depending on your printer.

Holder / case for TOPDON Infrared camera TC001 GoPro compatible

Made to hold a Philips Oneblade, beard trimming attachments, a spare head, as well as a Safety Razor and spare blades. All compartments have drain holes. Feet can be glued on the bottom if desired. The Oneblade can also be charged while in the stand, but only if the stand is placed on the edge of a shelf as per the photo, since the charging plug is enormous on these things, and I didn't want to make a giant stand.

Shaving accessories stand for philips oneblade

Shaving stand v6.stl

Made this for my girlfriends' iPhone 11 with case. Would probably work for any other phone that's close to these dimensions, up to a maximum of 81mm wide and 15mm deep. Hole for cable at the bottom, and cable retention notch to hold the cable when the phone is not in the holder. Countersunk screw hole in the back.
Prints upright with no support. 

Phone wall mount, size 81mm W x 15mm D

This is designed to fit in the little hole of the shock mount on my Ibis Ripmo AF (XL) mountain bike and it holds a 4, 5, and 6mm allen key. Can be secured with a cable tie, or some double sided tape. Printed in PETG. No supports needed if printed on its side.
 I don't know if it will fit any of the other frame sizes.

ibis ripmo AF frame mountainbike tool holder

This is designed to fit in the little hole of the shock mount on my Ibis Ripmo AF (XL) mountain bike and it holds a 4, 5, and 6mm allen key. Can be secured with a cable tie, or some double sided tape.
 I don't know if it will fit any of the other frame sizes.

Cable storage bin with 10 18mm wide compartments, to fit various size USB or other cables. Fits USB cables up to 10ft length depending on diameter. Base is Gridfinity compatible 42mm squares (2x5), but top is not stackable.

Took about 12hrs to print in PLA on an Ender 5. No supports needed.

USB Cable organizer storage bin - Gridfinity

Cable storage bin with 10 18mm wide compartments, to fit various size USB or other cables. Fits USB cables up to 10ft length depending on diameter. Base is Gridfinity compatible 42mm squares (2x4), but top is not stackable.

Took about 12hrs to print in PLA on an Ender 5. No supports needed.

Little shelf to hold the different attachments for my vacuum cleaner. First version has four 15mm by 50mm tall posts for my oddly shaped Shark brand vacuum. Made a second version with five 23 by 45mm posts that would probably work better with larger diameter standard round tube accessories.

Vacuum attachment holder

vacuum attachment holder 4x15mm.stl

Bracket to mount the Fosi Audio BT30D Mini amplifier to the underside of my work bench. Would also work for vertical mounting. Print on its side with no supports. Countersunk 6mm holes. May require washers to adjust how tight it clamps.

Fosi BT30D Amplifier under-desk Mounting Bracket

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

dirk.mohrmann82

Achievements

Seedling

Explorer

Fan Favorite