Any questions reach out on Instagram - https://www.instagram.com/designbydave_aldrich/

Medium Size Now Available!
Small Size Here - https://thangs.com/designbydave/DBS-3D-Printed-Carbon-Fiber-Bicycle-Frame-40231

Video breakdown - https://youtu.be/baJIxkLU98w

See full playlist for more info on the build - https://youtube.com/playlist?list=PLZbAxl62ULQvcmdNVjiKLCC5SVoM-k3Fc

Google Drive shared folder with STL files and Documents - https://drive.google.com/drive/folders/1-s83oGZZNBDJ3QmTnrI9ZYfnnFFJOd0l?usp=sharing

Printing Parts

Material: CarbonX EZ-PC from 3DXtech or similar structural material
0.6mm nozzle
0.36mm layer height
6 perimeters (@0.65mm extrusion width = 3.9mm wall thickness) or more
6 top and bottom layers (@0.36mm = 2.16mm)
90-100% infill for dropouts
50-70% infill for headtube, rear brake mount, seat tube to top tube and bottom bracket
When in doubt, favor wall thickness to infill percentage
Custom supports are designed into the parts and should be sufficient at least with the CarbonX material (except the Rear Brake Mount part, that will likely need auto generated supports for the bridge area.)
Use a ~5mm brim

Carbon Tubes Needed
50x48x1000 mm - headtube and downtube
30x28x1000 mm - seat tube and toptube (2 pieces)
18x16x1000 mm - or - 18x15x1000mm - chainstays
15x13x1000 mm - or - 15x12x1000mm - seatstays (2 pieces)
See included BoM for more details

Cutting Tubes

Use 3D printed templates to mark tubes using the spacing between templates provided in the documentation.
Use a rotary tool to cut and gradually bring tube cuts to shape.

Assembly Jig

You will need some form of assembly/alignment jig. My design is included but uses 45x90mm aluminum t-slot rails. That’s probably overkill and expensive (they were donated to me.) You can probably substitute something much smaller and cheaper but will have to modify the included design (pretty simple change to make to the printed parts.)

Coat all parts that might get epoxy on them with a release agent like PVA. Don’t want to glue your frame to the jig!

Assembly procedure

Start by gluing the aluminum prefabricated dropouts to the printed dropouts. Install the threaded bottom bracket into the printed part (BE SURE TO CHECK THREAD ORIENTATION, THERE IS A LEFT AND RIGHT SIDE.)

Scuff up all the mating areas of the tubes with a coarse grit sandpaper to ensure a good key.

Assembly order:
Attach bottom bracket to fixture
Seat tube into bottom bracket
Seat tube - top tube part
Chain stays
Rear brake mount and seat stays
Dropouts
Downtube
Headtube and top tube together
Bottle cage mounts

Bike Fit Geometry (Sizing)

This is the Medium Size which should be suitable for riders between 5’7” and 6'0" or so. Small size available for shorter riders and Large size coming later.

DISCLAIMER:
This design has to be seen as a proof of concept, demonstrating that such a project can be achieved with 3D printing. As of the time of upload I have around 200 miles on the first prototype of real-world, low to moderate intensity riding with no issues. Having said that, I have done no amount of structural load testing. The frame is not ISO 4210 certified. Print, assemble and ride at your own risk.

Future versions and features to develop

Large Size
Internal cable routing
Disc brakes - Add brake mount to left dropout. Change dropouts to through axle. Change Rear Brake Mount part to remove unnecessary material and rim brake caliper mount / add more tire clearance. Source new fork
Mods / add ons for pedal assist ebike system
ISO certification
Frame structural optimization, simulation
Study of FDM load testing and calibration of numerical simulation
Requests?

DBS 3D Printed Carbon Fiber Bicycle Frame - Medium

seat_tube_shim_28mm.SLDPRT

1_DBS_Medium_v1.0_Assembly

tubes_medium_v1.0-1

Head_tube_medium_v1.0-1

Bottom_Bracket_medium-1

seat_tube_top_tube_medium_v1.0-1

rear_brake_mount_medium_v1.0-1

C41-right-1

C41-left-1

dropouts_medium_v1.0-1

tube_cut_guides_medium_v1.0-1

cable_stops_and_cage_mounts_medium_v1.0-1

seat_tube_shim_28mm-1

Any questions reach out on Instagram - https://www.instagram.com/designbydave_aldrich/

Medium Size Now Available - https://thangs.com/designbydave/DBS-3D-Printed-Carbon-Fiber-Bicycle-Frame--Medium-42394

Video breakdown - https://youtu.be/baJIxkLU98w

See full playlist for more info on the build - https://youtube.com/playlist?list=PLZbAxl62ULQvcmdNVjiKLCC5SVoM-k3Fc

Google Drive shared folder with STL files and Documents - https://drive.google.com/drive/folders/1-s83oGZZNBDJ3QmTnrI9ZYfnnFFJOd0l?usp=sharing

Printing Parts

Material: CarbonX EZ-PC from 3DXtech or similar structural material
0.6mm nozzle
0.36mm layer height
6 perimeters (@0.65mm extrusion width = 3.9mm wall thickness) or more 
6 top and bottom layers (@0.36mm = 2.16mm)
90-100% infill for dropouts
50-70% infill for headtube, rear brake mount, seat tube to top tube and bottom bracket
When in doubt, favor wall thickness to infill percentage
Custom supports are designed into the parts and should be sufficient at least with the CarbonX material (except the Rear Brake Mount part, that will likely need auto generated supports for the bridge area.)
Use a ~5mm brim

Carbon Tubes Needed
50x48x1000 mm - headtube and downtube
30x28x1000 mm - seat tube and toptube
18x16x1000 mm - or - 18x15x1000mm - chainstays
15x13x1000 mm - or - 15x12x1000mm - seatstays (2 pieces)
See included BoM for more details

Cutting Tubes 

Use 3D printed templates to mark tubes using the spacing between templates provided in the documentation.
Use a rotary tool to cut and gradually bring tube cuts to shape. 

Assembly Jig

You will need some form of assembly/alignment jig. My design is included but uses 45x90mm aluminum t-slot rails. That’s probably overkill and expensive (they were donated to me.) You can probably substitute something much smaller and cheaper but will have to modify the included design (pretty simple change to make to the printed parts.)

Coat all parts that might get epoxy on them with a release agent like PVA. Don’t want to glue your frame to the jig!

Assembly procedure

Start by gluing the aluminum prefabricated dropouts to the printed dropouts. Install the threaded bottom bracket into the printed part (BE SURE TO CHECK THREAD ORIENTATION, THERE IS A LEFT AND RIGHT SIDE.)

Scuff up all the mating areas of the tubes with a coarse grit sandpaper to ensure a good key.

Assembly order:
Attach bottom bracket to fixture
Seat tube into bottom bracket
Seat tube - top tube part
Chain stays
Rear brake mount and seat stays
Dropouts
Downtube
Headtube and top tube together
Bottle cage mounts

Bike Fit Geometry (Sizing)

This is a Small size which should be suitable for riders between 5’3” and 5’7” or so. Medium size here - https://thangs.com/designbydave/DBS-3D-Printed-Carbon-Fiber-Bicycle-Frame--Medium-42394
Large size coming in the future. 

DISCLAIMER:
This design has to be seen as a proof of concept, demonstrating that such a project can be achieved with 3D printing. As of the time of upload I have around 200 miles on the first prototype of real-world, low to moderate intensity riding with no issues. Having said that, I have done no amount of structural load testing. The frame is not ISO 4210 certified. Print, assemble and ride at your own risk. 

Future versions and features to develop

Large Size
Internal cable routing
Disc brakes - Add brake mount to left dropout. Change dropouts to through axle. Change Rear Brake Mount part to remove unnecessary material and rim brake caliper mount / add more tire clearance. Source new fork
Mods / add ons for pedal assist ebike system
ISO certification
Frame structural optimization, simulation
Study of FDM load testing and calibration of numerical simulation 
Requests?


1_DBS_Small_v1.0_Assem1

DBS 3D Printed Carbon Fiber Bicycle Frame

tubes_small_v1.0-1

head_tube_small_V1.0-1

seat_tube_top_tube_small_v1.0-1

rear_brake_mount_small_v1.0-1

dropouts_small_v1.0-1

bottom_bracket_small_v1.0-2

Assembly jig-1

cable_stops_and_bottle_cage_mounts-1

tube_cut_guides_small_v1.0-1

Hi I'm Dave and I pretty much just build stuff. Check out my Youtube channel -  youtube.com/c/designbydave
Follow me on Instagram - instagram.com/designbydave_aldrich

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

designbydave

Achievements

Explorer

Seedling

Up and Coming

DBS 3D Printed Carbon Fiber Bicycle Frame - Medium

DBS 3D Printed Carbon Fiber Bicycle Frame