I have a glass shower door that had broken spacers allowing the handle to rattle into the glass, I was able to disassemble it and use calipers to duplicate the measurements. the piece came out perfectly. I have printed this in polycarbonate, petg and PPA-CF and all of them seem to work. I installed the ones in PPA-CF and kept the polycarbonate ones as backup. Hope this helps someone in the same situation.

Glass shower door piece final.3mf

Made a gridfinity mount for my Wahl detailer. It has a cutout for the rotating cord and a tight fit for the charging base.

Wahl detailer lithium ion

Wahl trimmer final.3mf

made a holder for my oral b electric toothbrush. the Challenge was that the cable for the charger doesn't disconnect. So I split it with dovetails. It's a very tight near permanent fit so don't do what I did and test putting them together without running the cable first.   

Oral B toothbrush charger gridfinity.3mf

I bought a dechoker https://dechokerinternational.com and had it stored in a junk drawer. I realized that probably wasn't too smart if we ever needed it in a hurry. So I made a simple wall mount.

Dechoker wall mount 

Dechoker mount v1 ken made.3mf

I hated the provided stand for my milk frother. It constantly fell over trying to take the frother in and out. This one doesn't do that. https://a.co/d/7HCq4Zx 

I would print this on its back with tree supports, that's the best success I've had. be careful removing supports and super glue fixes a lot of mistakes.

zulay milk frother stand

Milk frother stand v3.3mf

I printed https://makerworld.com/en/models/586783?from=search#profileId-508053 this model and realized I had no bic pens in my house so I modeled a 3d printed version. works great. If you have fit issues scale to .96%

Bic arrow 3d printed

DIY arrow v2.3mf

I modeled a snap fit gridfinity holder for my older Tesla model S spare key. It works great for what I wanted, it is a tight fit though, needs to be shaken to take out

model s key gridfinity

Model s key gridfinity v2 1x2 kenmade.3mf

I bought this from amazon: https://a.co/d/da8PZ6T and immediately made a gridfinity custom box for it. it's 1x3 and stores the ratchet and the bits

Right angle ratchet gridfinity custom holder

Right angle ratchet v1 gridfinity 1x3 ken made.3mf

I installed an amazon basics wire rack,but every time we would take the Tesla charger off the wall it would knock over the things we had stored. so I took this pipe clamp: https://www.thingiverse.com/thing:3631405 and this Tesla charger holder https://www.thingiverse.com/thing:4913564 and with the modeling skills of a talented 8 year old I put them together. it worked... ok. You either need to import it as one piece and use supports or do what I did, forget and then bend the pieces to fit it together after. But! results matter the most, and this works.

Pipe clamp Tesla charger holder 25mm remix

Pipe clamp Tesla charger holder 25mm remix.3mf

I made a 3x4 gridfinity for my nice pocket knives. Can't imagine maybe people have the same ones, but maybe this will save someone a couple hours of work. I put the labeling in in bambu slicer

gridfinity 3x4 custom pocket knife storage axial bench made SOG

Kens knife storage v2 3 x4 gridfinity.3mf

the rubber T handle on the Club Car Precedent with a utility attachment broke, so I modeled this off of a generic amazon replacement.

T handle golf cart part replacement.3mf

T handle golf cart part replacement V3 KEN MADE FINAL.3mf

this is my 3d model of my european style 10 inch chefs knife. I use this as a template. Have to print at an angle to fit on my printer 

Eurofighter 10 inch chefs knife model

very functional but unfortunate looking 3d scan to storage  cutout of my degree deodorant stick. 4x1 bin.

gridfinity deodorant storage 4x1

A bin I made for my bathroom gridfinity project to hold my nail clippers. stackable in one orientation easily grabbable in the other. magnet ready 2x1 bin. these are the nail clippers: https://a.co/d/0gAR0jk

nail clipper gridfinity bin

simple under workbench mount for extra 2x72 grinding belts. Works great.

2 x 72 belt grinder belt holder v2.2.3mf

fully 3d printed cover for the Marantec m3 631 garage door remote opener I remodeled it from Steve Johnsen on printables.
https://www.printables.com/en/model/181419-marantec-m3-631-garage-door-opener-cover

garage keypad cover.3mf

I built a coat rack out of 1 inch black pipe from home depot, after putting it together, it was uneven. Printed this to level it. Snap fit into a 3 hole flange

1 inch black pipe flange level

poorly Remixed version of Colombojrj's wall mounted gridfinity holder for slatwall. 4x4 gridfinity

gridfinity wall mount slatwall

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

adroit1313

Achievements

Seedling

Debutant

Trailblazer