A print in place toilet paper holder with quick release and load functionality. It also has spring action so that the leavers return to the original position. I could be wall mounted with some m3 screws or use strong double sided adhesive. Also, print 2 Springs.

Print settings:

layer height: 0.25 (it should work with other layer heights as well)
supports: none
There is some bridging. Try to slow down print speeds for the bridging section in your slicer.

Once off the build plate, use a bit of force to get the arms moving. Move the arms about a few times and use some lubrication if you have some handy.

If you plan to use double sided adhesive I would recommend to sand down the back side of the holder so that the tape grips well to the plastic (Make sure to wipe down after sanding)

Mount the holder in the desired location and insert the strings.

Toilet Paper Holder - print in place/quick load and release

Toilet paper holder v1.stl

Hooks to hold a mallet for the IKEA SKADIS board. 

Print 2 of these.

Should hold a ~67mm (2.6in) diameter rubber mallet

Mallet holder IKEA SKADIS board

Mallet holder SKADIS board

A simple support for plates printed in place using 1 layer as the hinge. 

2 models available. 1 for very small plates and one a little bit larger for bigger plates.

Print flat with 1st layer at 0.25mm. Prefer PETG as it is more flexible but PLA can also be used but with higher temps so that it does not print brittle.

You could also remove the top layer to show on the outside the pattern of the infill

You can scale these but in your slicer make sure that the first layer is 0.25mm (use either slicer split tool or move print slightly under the bed so that this height is reached) 

Plate Holder (Print in Place)

Bigger plate holder.stl

This is a hand mounted tape dispenser for easy gift rapping poster hanging, etc.

Printed in 2 main parts: 

The base: no special printing considerations here. Suggest that you use PETG as it is more flexible then PLA although it should work with PLA as well.

The cutter which should be printed separately in the orientation shown in one of the pictured

This is printed in different orientation as to have sharper edges for tape cutting. Having sharp edges made out of plastic is a challenge for this application. this strategy gave the best results. Print slowly (supports are required) and with perimeter edges set at .30mm in the slicer. This should turn out well with a .40 nozzle. Layer height .2 or even .15

Once everything is printed. insert the cutter into the base as shown in one of the pictures

This tape routing element is present in the eventuality that the cutter is not as sharp and has difficulty cutting the tape in its normal position. Is should provide a sharper angle and hopefully assist with better cutting.

SUNLU black PLA used: 

SUNLU PLA

Use Coupon code for a discount: 7JOWET2KWG

Tape dispenser/holder hand mounted

tape hand holder base.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4918286.

Designed from maxr525 file. Added support leg so as to be able to hang it from a shelf or cabinet using double adhesive tape. 

Google Home Mini hanging holder (double adhesive)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4936889.

Designed a Makita DHS680Z dust bag since I currently do not have a shop vac or for instances when needing to take it outside.

I designed it so that there is a hole in the filleting cap. This should allow displaced air to escape. It is also possible to place a filter of sorts so that the dust dust not come out.

Printed on a Chiron with a 0.6 nozzle in the shown orientation, with supports from build plate. It could be difficult to print but it has worked for me for the first time. 

Print should also fit an Ender 3 but have not tested it yet.

https://youtu.be/wZfL-00mzLQ

Circular Saw dust Bag for Makita DHS680Z

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5335750.

Video:
https://youtu.be/UjAUg7r8sD8

Designed and 3D Printed a case for the Sony ZV-1. Decided to use a softer inner shell made of TPU filament and a harder outer later out of PLA plastic. The case has a built in hinge and a simple locking mechanism. 

⭐Filament acquired from Aliexpress (affiliate links): 

PLA: https://s.click.aliexpress.com/e/_A8tY4x 

TPU: https://s.click.aliexpress.com/e/_A34m47 

 

⭐Mellow Direct Drive extruder seen on printer can be purchased from this link with everything included: 

https://s.click.aliexpress.com/e/_AtsTXa 

Sony ZV-1 Camera Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4848763.

Have a few watches around. Decided to make a watch stand. As you can see, it can fit 4 large watches (barely :)).

Printed upright with support from the top of the base. Maybe some will find a better way to print. 

Yogitech like coffee, support here:
https://ko-fi.com/yogitech

Watch Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4589574.

My first contribution on Thingiverse and first design. This is a 3D printed USB Power bank based on MakerHawk 18650-Board (H961-U v3):

https://www.amazon.co.uk/gp/product/B07VJLNH6Q/ref=as_li_tl?ie=UTF8&camp=1634&creative=6738&creativeASIN=B07VJLNH6Q&linkCode=as2&tag=goanta-21&linkId=7879cb6e269779f70be4359bf62a8fbd


Adapted a touch sensor instead of the build in tactile switch of the board to display charge info. Used this touch sensor:

https://www.amazon.co.uk/gp/product/B07VJLNH6Q/ref=as_li_tl?ie=UTF8&camp=1634&creative=6738&creativeASIN=B07VJLNH6Q&linkCode=as2&tag=goanta-21&linkId=7879cb6e269779f70be4359bf62a8fbd

The bottom of the case is designed to hold 6 18650 cells (more could be packet it). In my case, I used 6 old laptop cells and connected them in parallel (as the board specifies).

The top and bottom parts combine using clamping pressure. Caution here as once put together may be difficult to take apart.

IMPORTANT:
I have not designed any side openings for the board tactile switch or the Lightning opening as in my situation, they are not used.

Video of touch:
https://youtu.be/A9QZ6dV1_S8

USB Power bank based on MakerHawk 18650-Board case (H961-U v3)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4652503.

Another laptop support. This is intended to be fixed on the side of a desk, inside or out. 
It has 3 mounting screws and holes on the other side so that a screwdriver can fit through and tighten the screws.

Mainly done for my Dell PRECISION M7530. can be easily adapted to other laptop sizes.

Yogitech like coffee, support here:
https://ko-fi.com/yogitech

Another Laptop Mount

cutter.3mf

cutter.stl

hand tape holder base.3mf

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

YogiTech

Achievements

Seedling

Debutant

Pinned models

Watch Stand

Tape dispenser/holder hand mounted

Toilet Paper Holder - print in place/quick load and release

Mallet holder IKEA SKADIS board

Plate Holder (Print in Place)

Tape dispenser/holder hand mounted

Google Home Mini hanging holder (double adhesive)

Circular Saw dust Bag for Makita DHS680Z

Sony ZV-1 Camera Case

Watch Stand

USB Power bank based on MakerHawk 18650-Board case (H961-U v3)

Another Laptop Mount