Simple claw to add to gloves/paws for costumes! 

Simple claw

claw.stl

Tuning peg STL model for a medieval lute/guitar/ukulele etc. I designed these for my jaskier lute prop! 

lute-peg.stl

Lute tuning peg but without the pin (hole suitable for 6-6.2mm diameter) in case you already have some suitable sticks.

lute-peg top.stl

Roller to texture eva foam, custom made with sharper edges to be rolled on heated eva foam to emboss a wood grain for cosplay and props. 
Print without supports. Suitable for 3/4 inch rod as handle to roll it. 

You can also print it in flex filament and dip it in paint to create a paint roller!

Texture foam roller - wood grain.stl

Illidan hand stand for Skull of Gul'dan seen here: https://thangs.com/Willowcreative/Skull-of-Guldan-16571

Illidan hand stand for Skull of Gul'dan

4-in-1-weave scalemail with a slight curvature and attached custom supports. Based on The Ring Lord large scales. 
This works great and very fast for MSLA resin printers! Tested on my Phenom resin printer, includes a piece scaled exactly to the Phenom build volume and a smaller test piece size which you can multiply and link together (offset X +96mm and Y +48mm).
If your 3d printer does not match the size exactly, let the excess overhang and slice as usual. The half printed rings on the edges should fall right off or can be clipped off.

Size of the rings/scales is 10mm diameter. Scales are 33mm long (the ring lord 'large' dimensions)

These have custom supports included! Load and slice-ready! Write time may take a long time due to the amount of detail. Turn off volume calculation to speed up slice time.

Recommended to use tough/tenacious type resin if you plan on using this for a costume etc, so the connections don't break easily.

These are rotated 90 degrees vs my other scalemail files, because the scalemail sheet stretches in the direction of the scales, placing it on the shortest axis of the resin printer to create a somewhat square sheet as final result (and not a long stretched piece). 

 Scalemail 4 weave for MSLA printers (perpendicular direction)

scalemail_test_supported2.stl

4-in-1-weave scalemail with a slight curvature and attached custom supports. Based on The Ring Lord large scales. 
This works great and very fast for MSLA resin printers! Tested on my Phenom resin printer, includes a piece scaled exactly to the Phenom build volume and a smaller test piece size which you can multiply and link together (offset X +80mm and Y +48mm).
If your 3d printer does not match the size exactly, let the excess overhang and slice as usual. The half printed rings on the edges should fall right off or can be clipped off.

Size of the rings/scales is 10mm diameter. Scales are 33mm long (the ring lord 'large' dimensions)

These have custom supports included! Load and slice-ready! Write time may take a long time due to the amount of detail. Turn off volume calculation to speed up slice time.

Recommended to use tough/tenacious type resin if you plan on using this for a costume etc, so the connections don't break easily.

Scalemail 4 weave for MSLA printers

scalemail_test_supported.stl

Skull of Gul'dan from Warcraft, signature artefact of Illidan. Included is a solid STL for FDM printing, and a hollowed out STL, 3mm wall and with supports suitable for medium to large MSLA printers.


Find the matching Illidan hand stand here: https://thangs.com/Willowcreative/Illidan-hand-stand-for-Skull-of-Guldan-17032

Skull of Gul'dan

guldan skull.stl

Arrowhead and nock

arrowhead.stl

4-weave chainmail of standard round ringed chainmail with a slight curvature and attached custom supports. Sized for the Mono X and Saturn (190mm by 120mm).
Size of the rings is 10mm diameter

These have custom supports included! Load and slice-ready! Slice and write time may take a long time due to the amount of detail.

Supported chainmail for Anycubic Mono X

4-weave chainmail of standard round ringed chainmail with a slight curvature and attached custom supports. Sized for the Elegoo Saturn (190mm by 120mm).
Size of the rings is 10mm diameter

These have custom supports included! Load and slice-ready! Slice and write time may take a long time due to the amount of detail.

Supported chainmail for Elegoo Saturn

4-weave chainmail of standard round ringed chainmail with a slight curvature and attached custom supports. These work great for MSLA resin printers! Tested on my Phenom resin printer, includes a piece of chainmail scaled exactly to the Phenom build volume and a smaller test piece size which you can multiply and link together.
If your 3d printer does not match the size exactly, let the excess overhang and slice as usual. The half printed rings on the edges should fall right off.

Size of the rings is 10mm diameter

These have custom supports included! Load and slice-ready! Slice time may take a long time due to the amount of detail.

This upload has higher tolerances than the previous upload, so if your printer has a lower pixel resolution there's better chance of success.

#2 Supported chainmail 4 weave for MSLA printers

4-weave chainmail of standard round ringed chainmail with a slight curvature and attached custom supports. These work great for MSLA resin printers! Tested on my Phenom resin printer, includes a piece of chainmail scaled exactly to the Phenom build volume and a smaller test piece size which you can multiply and link together.
If your 3d printer does not match the size exactly, let the excess overhang and slice as usual. The half printed rings on the edges should fall right off.

Size of the rings is 10mm diameter

These have custom supports included! Load and slice-ready! Slice time may take a long time due to the amount of detail.

Supported chainmail 4 weave for MSLA printers

chainmail_test_supports.stl

4-weave chainmail of standard round ringed chainmail with a slight curvature. These work great for MSLA resin printers! Tested on my Phenom resin printer, includes a piece of chainmail scaled exactly to the Phenom build volume and a smaller test piece size which you can multiply and link together.
If your 3d printer does not match the size exactly, let the excess overhang and slice as usual. The half printed rings on the edges should fall right off.

Includes smaller and larger rings variants (approx 10mm and 12mm diameter rings). The larger rings print a bit easier and are easier to remove from supports due to bigger tolerances.

Pay attention to the support settings! Important for a successful print!

Support information for Chitubox:
75% density
Medium supports preset
Z lift height: 6mm
Angle 20%

If you are filling your entire platform:
Turn OFF raft
Turn NONE bottom platform touch shape 
This is to prevent FEP suction and failure since you are filling your entire plate

Chainmail 4 weave for MSLA printers

chainmail_phenom.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Willowcreative

Achievements

Seedling

Fan Favorite