Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4637180.

Remixed https://www.thingiverse.com/thing:4601328 with legs added to clip onto the middle of the sink. My sink was around 30mm at the top and gently sloped outwards, designed this with the legs straight down so they flex slightly and grip onto the sink.

Dish Scrubber Holder with Attachment for Kitchen Sink

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5157102.

Remix of [Atoban's Side Spool System for Sidewinder X1](https://www.thingiverse.com/thing:4588508) updated for the Sidewinder X2. Artillery added the plastic across the top of the gantry so the X1 design doesn't fit. Additionally, the frame piece spool holder needed trimming so the extruder rail doesn't run into it at Z=0. I also added some clearance into Atoban's design of the spool holder and bottom frame piece since I could never make them fit together and onto the frame without sanding.

2 versions are available: 
v1- Plain Spool Axis. I've been using this design on my X1 for over a year with no issues.
v2- Spool Axis with roller. This is similar to [Atoban's Side Spool System V2 for Sidewinder X1](https://www.thingiverse.com/thing:4609575) but uses one of the rollers that comes with the X2's spool holder. I personally find this design rolls too much, so too much filament comes off the spool and can get tangled. 

**No additional hardware needed!** You will need an 8mm socket wrench though. This design uses a bearing and 3 of the screws from the stock spool holder. 1 screw is used for the bearing in the the pulley and 2 screws replace the 2 in the top of the gantry. The original ones in the gantry end up being a little short with the new piece added so the threads in the gantry could strip easily.
**Edit 12/26/21:** Sounds like some of the X2's aren't coming with the bearings, instead they come with rods inside the rollers. If that's the case, you'll need a 11mm OD bearing with a 12.5mm flange for the pulley. These [uxcell F685ZZ Flanged Ball Bearing 5x11x5mm Shielded Chrome Steel Bearings 2pcs by uxcell](https://smile.amazon.com/dp/B07Z3DTT2X/ref=cm_sw_em_r_mt_dp_5VZG7C3B2ZKJW9B41Q6N?_encoding=UTF8&psc=1) should work. You will need 3 bearings if you want to use the v2 axis with the roller.

**No supports should be needed.** I printed in blue PLA with 4 walls and 20% infill. 

v1 Assembly instructions: 
1. Print one of each piece as oriented (besides those labeled v2)
2. Fit the top 2 pieces together as well as the bottom two pieces
3. Remove the gantry by unscrewing the 4 screws on the bottom of the printer, slide the bottom frame piece in, and reattach the gantry
4. Remove 3 of the screws and bearings from the stock spool holder
5. Remove the 2 screws from the top left of the gantry, align the printed top frame piece to the holes, and use 2 of the screws from the stock spool holder to secure
6. Attach the filament sensor and route the cable as pictured. Make sure the cable is pulled tight between the clips so it doesn't rub on the z-axis belt.
7. Insert a bearing from the spool holder into the pulley from the side of the pulley with the larger center opening. The lip of the bearing should be facing the larger opening side so it stays seated. This way the pulley won't fall off.
8. Insert a screw from the spool holder into the top piece from the back. Slide on one of the washers from the spool holder, the pulley with bearing, and then the locknut. Tighten with an 8mm socket. 

v2 assembly instructions:
1. Print one of each piece besides the spool axis labeled v1. 2 of the M5x16 printed bolts are needed.
2. Fit the top 2 pieces together. 
3. For the spool mount, see the v2 spool mount assembly picture. Credit goes to Atoban for the picture. 2 of the bearings and brass washers from the stock spool mount are used. The bolts are the the printed M5x16 bolts since you'll need 3 of the real M5x16 bolts from the stock spool holder for the top assembly.
4. Continue with step 3 on the v1 instructions.

 Side Spool System for Artillery Sidewinder X2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4637192.

Needed a spot for my webcam to sit out of the way. I have my printer on a Muscle Rack (made by Edsal) and this allows it to sit nicely out of the way but still get a great view.

Edsal Muscle Rack Shelf Webcam Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5524353.

Replacement handle for Sterilite 1215 2 bushel laundry basket. It may fit other Sterilite baskets with the same style handles. This replaces the entire handle so if the white bottom part is still intact, you'll have to trim that out. A side cutter or utility blade makes quick work of it. Seems very sturdy, definitely stronger than the original handles. 

No extra hardware required. It friction fit well enough on mine that I don't really even need to glue it on. I would think either hot glue or super glue would hold well if needed though.

Printed in PETG with 5 walls and 10% infill. Used a .8mm nozzle with .4mm layer height for fast printing. Print on its side so you get nice lines on the top and you don't see the layers as much. 

Sterilite Laundry Basket Handle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5899229.

Print on its side and use supports for the tabs. Does not work well with the Energizer model with the clear controller holder but seems to work on other Energizer/PDP systems.

Xbox Series X/S Controller Battery Cover for Energizer/PDP Charge System

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5500832.

Box to safely hold Tomcat Bait Chunx mouse poison bait. Designed similar to the Tomcat brand boxes to prevent larger animals and pets from getting the poison. The mouse is able to get into the box, eat the bait, and leave.

I printed in PETG for outdoor/sun durability but should be fine in PLA as well. .2 layer height with a .4 nozzle.

Mouse Bait Box for Tomcat Bait Chunx

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4637254.

The cellophane plastic that comes around some bath bombs is really a pain to take off without something sharp. We go through a few of them since our 3 year old loves bath bombs. We got something similar with a set of bath bombs we bought, thought we might need a spare and others might like this too. 

I almost threw it away the first time I saw it because it looks like a weird plastic bird head with a sharp beak. Hence the name and the words on this one.

Edit 6/10/21- Added a blank version with no writing on it by request

Bath Bomb Bird - The Bath Bomb Opener

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4852102.

Why I created this: I got up with our 4 month old daughter in the middle of the night and was pretty sure the (nearly full) bottle of breastmilk that got left out wasn't good anymore. Not wanting to wake up my wife who had been sick, I heated up a different bottle. Found out in the morning that she had left it out on purpose, expecting baby to wake up, and it would've been good. It wasn't by the morning so had to be dumped. Not wanting to re-experience the resulting scene that ensued, I came up with this design.

Bottle "Good Until" Safety Tag for Breastmilk and/or Formula

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5216080.

My version of a pour spout for a wide mouth mason jar. Pours smooth and has a "dripper" so the liquid doesn't run back onto the jar as you're pouring. 

Wide Mouth Mason Jar Pour Spout

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4655101.

Loved the design of Ben Heck's chip clip but my fingers always slide off when trying to pull it off a bag. Remixed it to have finger tabs. I also like the design of this because you can use it instead of a twist tie!

Ben Heck's Chip Clip Remix

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4653893.

This adapter lets you use the smaller 1.25" shop-vac hose on a tool with a 2.25" output like a Dewalt table saw (DWE7491RS) or benchtop planer (DW735x). I had one from Rocker [TA1066N](https://www.rockler.com/shop-vac-dust-fitting-adapter-for-1-1-4-to-2-1-4-diameter-hose) but didn't want to buy another one so made one that's easy to print with no supports.

v2 version may fit more snug on the 2.25" side.

Dust Port Adapter, 1-1/4'' Vacuum Wand to 2-1/4'' Dust Port

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4709091.

A tool to get the silicone cap off of the tubing port. Install the puller on the port before putting on the silicone cap and it'll pull off easily. Clips on to tubing for storage when not in use.

Got the idea from [swordfish45](https://www.thingiverse.com/thing:4565776) but couldn't get it to fit right.

Spectra Breast Pump Cap Puller

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5717887.

Ice fishing hole cover "phone saver". Fits on top of a hole made with an 8" auger and allows line to feed through the side for when you catch the big one. Designed this as an alternative to buying the Catch Cover sold in stores.

I printed with PETG and 100% infill, PLA should work fine though too. You'll need a print bed of at least 300x300mm to accommodate this.

Ice Fishing Hole Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5809949.

Support for ice fishing cameras like MarCum and Aqua-Vu. Arms fold out to sit nicely over a 8" ice hole. 

I printed in PETG with 10 walls/top/bottom layers and 30% infill. It floats easily with these settings, just in case it falls in the hole.

Ice Fishing Camera Panner

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4641856.

Stand for milk frothing pitcher so I don't have to hold it the whole time. Puts the pitcher bottom at 100mm from the metal shelf on the bottom.

Gaggia Anima Milk Frothing Pitcher Stand

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Wheesir

Achievements

Seedling

Debutant