My kids loved the Battle Arena (starter set), so we decided to get them several other of the pre-made decks to hold them off until they are old enough to build their own.  

This dolly holds 16 decks, with slots for the coins that come with them (both large and small versions), as well it has a slot in the back for the Battle Arena board/mat to fit, and the center is made to hold [the set of damage and status tokens](https://thangs.com/Trangoul/Pokemon%20TCG%20Tokens.stl-37174?manualModelView=true) I made for them.  

The bottom is slightly beveled to make the assembly easier if elephants foot is an issue on  your printer.  As usual the .step is uploaded to allow modifications if needed.

Printed in Overture PLA Pro on an Ender 3 v2.

Pokemon TGC Battle Arena 16 Deck Dolly.step

My kids loved the Battle Arena (starter set), so we decided to get them several other of the pre-made decks to hold them off until they are old enough to build their own.  

This dolly holds 16 decks, with slots for the coins that come with them (both large and small versions), as well it has a slot in the back for the Battle Arena board/mat to fit, and the center is made to hold [the set of damage and status tokens](https://thangs.com/Trangoul/Pokemon%20TCG%20Tokens.stl-37174?manualModelView=true) I made for them.  

The bottom is slightly beveled to make the assembly easier if elephants foot is an issue on  your printer.  As usual the .step is uploaded to allow modifications if needed.

This is a stereo Quarter-Wave Speaker I designed in fusion 360.  I am listing the speakers I used (bought in bulk at $0.48 each) and the Bluetooth amplifier I used ($13).  For very old CRT tv speakers, this little thing puts out quite a bit of volume and the bass is actually pretty good.  While my calculations of the wavelength are fine, the pathway might not be 100% optimal, but its very close.

Printed at 0.32 layer height for most parts, but the speaker cover/grill is 0.08 layer height.  Everything is in Blue PLA and fits fairly well.  I used hot glue to hold the side panels on (and to make it more air-tight).

https://www.parts-express.com/YDT613-68-2-1-4-x-5-Paper-Cone-Full-Range-Speaker-8-Ohm-77-289-2314

https://www.amazon.com/dp/B08Z3FBSDT/?coliid=I3ECBFZDC6LIL&colid=3OKL3BQJ2POP2&psc=1&ref_=lv_ov_lig_dp_it

Wave Speaker

Speaker Cabinet

Webcam mount for Logitech Webcam I made for my ender 3 v2.  I wanted it front mounted and at a angle, but not too far away.

I used the following plate and screw:
https://www.thingiverse.com/thing:4859975
https://www.thingiverse.com/thing:2033041

Ender 3 v2 Webcam Front Rail Mount.step

None of the Swiss Army Keyrings I found fit my keys right, so I made my own.  Uploading the .Step file so you can edit it to meet your needs.

Swiss Army Keyring

Damage Counters, Status Tokens, a holder for all of the coins (which includes a space for several official coins, both mid and large ones), and a lid to keep everything together.

Holder is designed for 30 10 damage counters, 10 50 damage counters, and 10 100 damage counters, and then five of each status counter.

Pokemon TCG Tokens.stl

Damage Counters, Status Tokens, a holder for all of the coins (which includes a space for several official coins, both mid and large ones), and a lid to keep everything together.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Trangoul

Achievements

Seedling

Debutant

Pokemon TGC Battle Arena 16 Deck Dolly.step

Wave Speaker

Ender 3 v2 Webcam Front Rail Mount.step

Swiss Army Keyring

Pokemon TCG Tokens.stl