Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3949059.

This is a Stock attachement to use with Gruneun`s "Nerf Stryfe PVC Stock Adapter".
Use his shoulder piece in combination with this gun adapter. 
PVC pipe fits snuggly in the end, the Attachement clips perfectly on the Gun (Electric and Spring).
Use an M6 Bolt and Nut to hold both pieces together and tighten the bold to keep the stock in folded or unfolded position.
A Wing-Nut is recomended.
Be a bit careful with the small pins that secure the whole thing on the gun.
They dont need much force to release the Stock, but could still break easily, depending on your Print (material etc).  


Nerf Stock Adapter 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3052368.

WARNING the heavy pullstrap decreases the range by about 2 meters!
This is a Mod for the Nerf Mega Bigshock.
To install it you just need a m3 bolt .

Nerf Mega Bigshock Pullstraps

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2335142.

.

Spinner Cap threaded with rims for grip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3052374.


This is a Mod for the Nerf Mega Bigshock.
You Insert it into the dartholder on the gun and screw a spax screw through the hole in the front.
That is everything it takes.

Nerf Mega Bigshock Ironsight Beltclip and Dart Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3951822.

Addon to :https://www.thingiverse.com/thing:2590061

This converts ehdrien`s Shotgun mod to a 32mm 16 bar pvc pipe.

If your european you will have a hard time finding the right size of pipe for this mod.
I bought 32mm PVC pipe from Ebay and used it with my adapter rings that just pushes in.


Nerf Magnus Shotgun 32mm PVC Pipe adapter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2198871.

.

Fischstäbchen Fishstick

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4463515.

Print with 100% infill on side.

Ikea Skadis Hook shoplike

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3052360.

This is a Barrel Mod for the Nerf Mega Bigshock.
The Gun works with it just like it did before.
Easy to install, just press it on.

Nerf Mega Bigshock Barrel

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4395678.

Print on side with 100% infill. 

Ikea Skadis Wera allen Wrench holder Hexplus etc

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4395731.

Print hooks on side with 100% infill.
Print the holder on the backside with supports and 100 % infill.

Attach hooks to the holder with 4  2,5x12 screws.

Ikea Skadis Wera Kraftform Kompakt holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4357732.

Its a shelf that consists of 2 pieces, that are held together by 2 M6 bolt´s with internal hex head.


You Need:
- 2x M6 bolt´s length 15 - 30mm
- a threadcutter for M6

The thread needs to be cut in the holes in the shelf itself.
The bolt´s are supposed to just go throught the bracket.


I made 2 Versions, one for a 25mm diameter rod and one for 18mm.
If you need another size, hit me up.

Shower shelf for rod 25 /18mm

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3949046.

This is am Front-End-Mod for the Hammershot.

NOT FOR STANDART CYLINDER.
Made for : https://www.thingiverse.com/thing:1274005

One Version with Big block up and one with the small block up, because some barrels have them upside down.
It i based on a model from deusnefum.
I improved it so it has more tolerance for the darts in the front.
I also added some chamfers, a spacer and on one Version the standard nerf barrel mount. 
I also improved some tolarances.
There is a little groove to insert a rubber O-Ring into. So even barrels without endstop fit and sit snuggly.

Nerf Hammershot Front-Mod

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3949089.

This is a replacement for the original Piston.
It worked perfectly afte I removed the supports.

Nerf Rampage Piston

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4395714.

Print on side with 100% infill.

Ikea Skadis Simple shoplike Hook

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3949053.

One Version with Big block up and one with the small block up, because some barrels have them upside down.
This is a Mod for the Alpha Trooper, it replaces the orange mini barrel in the front.
There is a little groove to insert a rubber O-Ring into. So even barrels without endstop fit and sit snuggly.
Prints good without supports.

Nerf Aplpha Trooper Barrel Adapter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2200680.

.

Fidget Spinner Cap with rim for grip

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

SimonH.

Achievements

Seedling